Instruction for Use

ManualsBrandsWhirlpool ManualsDishwashersMDW 5001 AGW

EN -1-

Chart

BEFORE USING THE APPLIANCE FOR THE FIRST TIME CAREFULLY READ THIS QUICK REFERENCE GUIDE AND THE ASSEMBLY INSTRUCTIONS!

400010787179

FOR ENERGY SAVING THE CONTROL PANEL DEACTIVATES AUTOMATICALLY AFTER 30 SECONDS IF NO CYCLE HAS STARTED.

PROGRAM

SELECTION

BUTTON

Push “P” button

(repeatedly) until

selected program

number is shown

on the display

(P1...Px) - see

“Table of

programs” - next

page.

After 3 seconds

the cycle

remaining time is

displayed.

START/PAUSE/

RESUME

BUTTON

Push this button to

start the selected

program: the

indicator lights up

and goes off at the

end of the program.

Press Start button or

open the door

during washing cycle

to pause the cycle -

the Start Indicator

blinks.

To resume the cycle

push Start button

and close the door.

CANCEL/OFF

BUTTON

Push this button to

switch off the control

panel.

If pressed for 3 seconds

when a program is

running it cancels this

program. If pressed

for 3 seconds when

the dishwasher is off,

it drains the water out.

If pressed during

program and delayed

start selection it

cancels the selection

and returns to

previous cycle and

option selection.

ECO PROGRAM

INDICATOR

When lit, it indicates that

standard program is active.

MULTIZONE

INDICATOR

When lit, it indicates the

wash in the upper or lower

rack only.

KEYBOARD

LOCK INDICATOR

When lit, it indicates that

keyboard lock is active.

WATER TAP

CLOSED - Alarm

Blinks when there is no inlet

water or water tap is closed.

WASH TIME DISPLAY

Indicates the cycle duration and the remaining time (h:min). With “Delayed start”

selected it indicates the time remaining until program start: “h24” if above

10 hours delay time remain and “h:mm” if below 10 hours delay time remain.

If “Fx Ey” messages appears on the display, see page 9 - chapter “What to do if...”.

DELAY INDICATOR

When lit, it indicates that delay

is active.

RINSE AID

INDICATOR

When lit (at the end of the

cycle), the rinse aid dispenser

needs to be refilled.

SALT INDICATOR

When lit (at the end of the

cycle), the salt reservoir needs

to be refilled.

JET Clean PLUS®

Thanks to the additional

power jets this option

provides a more intensive

and powerful wash in the

lower rack, in the specific

area.

TABLET

SETTING

This setting allows to

optimize the cycle

performances

according the type of

detergent used. Push

the Tablet button

(the indicator lights

up) if you are using

the combined

detergents in tablet.

If you are using

powder or gel

detergent, the Tablet

indicator on the

control panel has to

be off.

MULTIZONE

Allows you to choose

the washing zones. The

appliance washes both

racks by default

(indicators are not lit).

To wash only in specific

rack, press this button

repeatedly:

KEYBOARD

LOCK

This option allows you

to lock the buttons on

the control panel.

Children will not be

able to accidentally

start the dishwasher by

pressing the buttons on

the control panel when

this option is selected.

If you want to activate

this option hold down

the button for

3 seconds.

Repeat the same

operation to unlock the

panel.

only upper rack

(including cutlery

rack)

indicator lit

only lower rack

indicator lit

JET Dry®

This technology generates

outstanding drying results

thanks to a condensation

process that occurs inside

the dishwasher.

DELAYED START

BUTTON

Push the button

(repeatedly) to delay the

start of the program.

Adjustable from 0:30 to

24 hours. With each press

of the button, the delay

start increases by: 0:30 if

selection below 4 hours,

1:00 if selection is below

12 hours, 4 hours if

selection is above 12 hours.

If 24 hours reached, and

the button is pressed, the

delayed start is deactivated

- "OFF" message is shown.

Then press the START

button. The delay time can

be adjusted after Start key

press. The dishwasher will

start after the set time.

Reference guide

Maytag is a registered trademark

Summary of content (12 pages)

PAGE 1
Chart Reference guide BEFORE USING THE APPLIANCE FOR THE FIRST TIME CAREFULLY READ THIS QUICK REFERENCE GUIDE AND THE ASSEMBLY INSTRUCTIONS! FOR ENERGY SAVING THE CONTROL PANEL DEACTIVATES AUTOMATICALLY AFTER 30 SECONDS IF NO CYCLE HAS STARTED. ECO PROGRAM INDICATOR When lit, it indicates that standard program is active. WASH TIME DISPLAY Indicates the cycle duration and the remaining time (h:min).
PAGE 2
Chart Reference guide Table of programs Programs Loading instructions Available options Detergent Use for normal soiled dishes with dried-on food. Senses the level of soiling on the dishes and adjusts the program accordingly. When the sensor is detecting the soil level an animation appears in the display and the cycle duration is updated. The JET Clean PLUS® option is activated automatically with this program. To deactivate, press the JET Clean PLUS® button on the control panel.
PAGE 3
First time use How to set water hardness in order to always assure the best cleaning results Water hardness should be set before the first wash or if water hardness has been changed Water hardness level is factory set for medium-hard water (level 4). 1 9 1. Ask your water supply company what the water hardness is... When powder or gel detergent is used, regeneration salt must be added and water hardness level must be set as indicated in the table on the right.
PAGE 4
Daily check Adding rinse aid. How to adjust the rinse aid dosage regulator 2 Visual indicator If required, open the cover B (press the dedicated button). Check the rinse aid indicator to check the level into the dispenser. The rinse aid dosage can be adjusted to the detergent used. The lower the setting, the less rinse aid is dispensed (factory setting: position 4). Press the button to open the cover B. Using a coin or similar object, turn the arrow to the desired setting.
PAGE 5
How to load the racks Cutlery rack 4 Long tools can be loaded in the frontal part of the rack (if long tools do not fit in the cutlery rack they can be placed on foldable flaps in upper rack). How to remove cutlery rack (if available) - It could be useful to remove cutlery rack to load stem glasses in upper rack. - Open the two retainers (H) to take off the rack. When the cutlery rack is in place the retainers must always be closed.
PAGE 6
How to load the racks Upper rack 4 In the upper rack you can load glasses, cups, bowls and, in the right side of the rack, you can load the dessert dishes. Foldable flaps (A) when open help to load stemmed glasses, long utensils or coffee cups. Plate holders (B) can be folded down to load bowls.
PAGE 7
How to load the racks Lower rack 4 In the lower rack plates and pots can be loaded. Vertical plate holders (E) can be folded down to create more space to load pots. F E JET Clean PLUS ® uses the special water jets in the rear of cavity to wash more intensively the high dirty items. When the “Half load/Multizone” option is selected the cutlery basket - F (provided in some models) can be placed in the lower rack. How to use JET Clean PLUS® 1.
PAGE 8
Select program 6 Overview of programs The max. possible number of programs is illustrated in the chapter “Chart”. The corresponding programs for your appliance can be found on the panel (page 1). Choose program according to the attached table of programs (page 2). Duration of the program depends on the external conditions in the apartment, temperature and pressure etc. For hygienic reasons it is recommended to run a high-temperature cycle (e.g. Intensive 65) at least once per month.
PAGE 9
What to do if... If a fault occurs, before contacting the After-sales Service, make the following checks to try and remedy the problem. Most faults can be remedied by taking the following courses of action, quickly restoring normal appliance operation. The appliance... Possible causes... Solutions... salt indicator is lit - Salt reservoir is empty. (After refill the salt - Refill reservoir with salt (for more information - see page 3).
PAGE 10
What to do if... Crockery and cutlery... ...are not perfectly clean/have food residues ...have deposits: regeneration salt residue ...are not dry Possible causes... Solutions... - Too little space between dishes (incorrect arrangement of the concave items in the rack). - Arrange crockery so that items do not touch each other. Concave items (e.g. bowls, cups) must be arranged facing downwards in the rack. - Too little detergent; detergent too old or incorrectly stored.
PAGE 11
What to do if... Crockery and cutlery... Possible causes... Solutions... ...have discoloured plastic parts - Tomato/Carrot juice. ...opaque glasses, etc. - Dishes unsuitable for washing in dishwashers (porcelain), ...removable deposits on glasses - Usage of incorrect programs for glasses. - Dishes should be put together, to avoid touching each other. Do not put glassware together in baskets. Use suitable program for glass. ...
PAGE 12
Precautions and general recommendations 1. Packing The packaging materials are 100% recyclable and marked with the recycling symbol . 2. Removing the packaging and inspecting the contents After unpacking, make sure that the dishwasher is undamaged and that the door closes correctly. If in doubt, contact a qualified technician or your local retailer. 3. Before using the dishwasher for the first time - The appliance is designed to operate with a minimum ambient temperature of 5°C.