Instruction for Use

EN
13
Rinse aid and refined salt
Only use products which have been specifically designed
for dishwashers.
Do not use table/industrial salt or washing-up liquid.
Follow the instructions given on the packaging.
If using a multi-functional product it is not necessary to add
any rinse aid. However, we recommend that you add salt,
especially if you live in an area where the water is hard or
very hard.
(Follow the instructions given on the packaging).
If you do not add salt or rinse aid, the LOW SALT* and
LOW RINSE AID indicator lights will stay lit.
Measuring out the rinse aid
Rinseaidmakesiteasierforthecrockerytodry,aswaterrunsoff
the surfaces more readily and therefore does not leave streaks
or marks. The rinse aid dispenser should be filled:
• WhentheLOWRINSEAIDindicatorlight* on the control panel
is illuminated, a reserve supply of rinse aid is still available
for1-2cycles;
1.Openthedispenser“D” by pressing and pulling up the tab
on the lid;
2.Carefully introduce the rinse aidas faras the maximum
reference notch of the filling space - avoid spilling it. If this
happens, clean the spill immediately with a dry cloth.
3. Press the lid down until you hear a click to close it.
NEVER pour the rinse aid directly into the appliance tub.
Rinse-aid quantity setting
If you are not completely satisfied with the drying results, you
canadjustthequantityofrinseaid.Switchthedishwasheron
and off using the ON/OFF button. Press the Start/Pause button
3 times. Start it using the ON/OFF button; the setting is shown
on the display
(set to factory level).
Adjust the level of rinse aid supply using the P button.
Press ON/OFF to save the setting.
IftherinseaidlevelissettoZERO,norinseaidwillbesupplied.
TheLOWRINSEAIDindicatorlightwillnotgoonifyourunout
of rinse aid.
Up to maximum 4 levels can be set based on the dishwasher
model.
• Iftherearestreaksonthecrockery,setalownumber(1-2.)
• Ifthereare drops ofwaterorlimescalemarks, set ahigh
number (3-4.)
Setting water hardness
Everydishwasherisequippedwithawatersoftenerwhichuses
refined salt designed specially for this type of appliance to supply
water without limescale - used to wash the crockery.
This dishwasher has a setting which helps to reduce pollution
and optimises washing performance in accordance with the
water hardness level in your area. This information can be
obtained from your local water supplier.
Switch the dishwasher on and off using the ON/OFF button.
Press and hold down the Start/Pause button for a few seconds
until you hear a beep. Switch the dishwasher on using ON/
OFF; the set level will appear on the display
(water softener set
to medium level).
Adjust the hardness level using the P button (1-2-3-4-5* see the
water hardness table)
up to max 5 levels.
Press ON/OFF to save the setting.
Evenifusingmulti-functionaltablets,fillthesaltdispenser.
(°dH=hardnessmeasuredinGermandegrees-°f=hardness
measuredinFrenchdegrees–mmol/l=millimolesperlitre)
Measuring out the refined salt
In order to obtain the best possible results from a wash cycle,
make sure that the salt dispenser is never empty.
Refinedsaltremoveslimescalefromthewater,thusavoiding
the formation of deposits on crockery.
The salt dispenser is located in the lower part of the dishwasher
(see Description) and should be filled:
• Whenthegreenfloat* cannot be seen by simply looking at
the cap of the salt dispenser;
• WhentheLOWRINSEAIDindicatorlightonthecontrolpanel
is illuminated *;
1.Removethelowerrackandunscrewthe
cap (anticlockwise).
2.Thefirsttimeyoudothis:fillthewater
tank right up to its edge.
3. Position the funnel
* (see figure) and
fill the salt dispenser up to the edge
(approximately1kg).Itisnormalforalittle
water to leak out.
4.Removethefunnel*andwipeanysaltresiduesawayfrom
the opening; rinse the cap under running water and then screw
it on, the head facing downwards so as to let the water flow out
of the four slots (star-shaped arrangement) in the lower part of
the cap (cap with green float
*).
It is advisable to perform this procedure every time you add
salt to the dispenser.
Make sure the cap is screwed on tightly so that no detergent can
get into the container during the wash cycle (this could damage
the water softener beyond repair).
Whennecessary,measureoutthesaltbeforeawashcycle
so that any saline solution which has leaked out of the salt
dispenser is removed.
* Only available in selected models.
Water Hardness Table
Average salt dispenser
capacity duration
**
level °dH °fH mmol/l months
1 0 - 6 0 - 10 0 - 1 7 months
2 6 - 11 11 - 20 1,1 - 2 5 months
3 12 - 17 21 - 30 2,1 - 3 3 months
4 17 - 34 31 - 60 3,1 - 6 2 months
5
*
34 - 50 61 - 90 6,1 - 9 2/3 weeks
For values between 0°f and 10°f, we do not recommend the use of salt.
* a setting of 5 may increase cycle duration.
** 1 wash cycle per day.
M
A
X