Instruction for Use
EN
7
Start-up and use
Measuring out the detergent
A good wash result also depends on the correct amount
of detergent being used; exceeding the stated amount
does not result in a more effective wash and increases
environmental pollution.
Only use detergent which has been specifically
designed for dishwashers.
DO NOT USE washing up liquid.
Using excessive detergent may result in foam
residue remaining in the machine after the cycle
has ended.
The use of tablets is only recommended for
models which offer the MULTI-FUNCTIONAL
TABLETS option.
To achieve the best results from each washing and
drying cycle, powder detergent, rinse aid liquid and salt
should be used.
Compartment A: Washing detergent
Compartment B: Pre-wash detergent
1. Open cover C by pressing button
D.
2. Pour in the detergent after
consulting the
Table of wash
cycles
:
• For powder detergent use
compartments A and B.
• For detergent in tablet form: when
the cycle requires 1 tablet, place it
in compartment A and close the cover; when it requires 2,
place the second tablet at the bottom of the appliance.
3. Remove detergent residues from the edges of the
compartment and close the cover until it clicks.
A
B
D
C
* Only available in selected models.
Starting the dishwasher
1. Turn the water tap on.
2. Press the ON/OFF button: all the indicator lights on
the control panel will light up for a few seconds.
3. Open the door and pour in a suitable amount of
detergent (
see below
).
4. Load the racks (
see Loading the racks
) and shut the
door.
5. Select the wash cycle by turning the WASH CYCLE
SELECT knob in a clockwise direction: align the notch
on the knob with the number or symbol representing the
desired wash cycle. The START/PAUSE indicator light
will flash.
6. Select the wash options
* (
see adjacent information
).
7. Start the cycle by pressing the START button; the
indicator light will light up and remain lit in a fixed
manner. The indicator light corresponding to the wash
phase will switch on, signalling that the wash cycle has
begun.
8. At the end of the wash cycle the END indicator light
will switch on (fixed light). Switch off the appliance by
pressing the ON/OFF button, shut off the water valve and
unplug the appliance from the electricity socket.
9. Wait for a few minutes before removing the crockery,
in order to avoid burns. Unload the racks, beginning with
the lower level.
- The machine will switch off automatically during
certain periods of inactivity, in order to minimise
electricity consumption.
Modifying a wash cycle in progress
If a mistake was made during the wash cycle selection
process it is possible to change the cycle, provided that it
has only just begun: once the wash cycle has started,
switch off the machine by pressing and holding the ON/
OFF/Reset button. Switch it back on using the same button
and select the desired wash cycle and options.
Adding extra crockery
Press the Start/Pause button (the corresponding indicator
light will flash). Open the door, taking care to avoid the
escaping steam, and place the crockery inside the
appliance. Press the Start/Pause button (fixed light): the
cycle starts from the point at which it was interrupted.
If the Start/Pause button is pressed so as to pause the
machine, the wash cycle or the Delayed Start
* function
(if selected) is interrupted.
At this stage it is not possible to change the wash cycle.
Accidental interruptions
If the door is opened during the wash cycle, or if there is a
power cut, the cycle stops. It starts again from the point at
which it was interrupted once the door has been shut or
once the electricity supply is restored.
Wash options*
The OPTIONS may only be set, modified or reset after
the wash cycle has been selected and before the Start/
Pause button has been pressed.
Only the options which are compatible with the type of
wash cycle set may be selected. If an option is not compat-
ible with the selected was cycle
(see Table of wash cycles)
,
the corresponding LED flashes rapidly 3 times.
If an option is selected which is incompatible with another
option or wash cycle selected previously, the incompat-
ible option light will flash 3 times and switches off, while
the most recently selected setting remains lit.
To deselect an option which has been set by mistake,
press the corresponding button again.