Instruction for Use

ARISTON DISHWASHER - Instructions for installation and use 15
D
ISHWASHER
You have loaded your dishes and you now have
to set the wash cycle. It takes just one minute
to learn how
Starting the dishwasher
Ready, steady, go!
First of all.
Turn on the water tap completely
and press ON-OFF button "A". you
will hear a short beep and indicator
light "B" lights up. Now the
appliance is on and awaiting in-
structions.
Selecting the wash
cycle.
To select the wash cycle, turn knob
"E" clockwise until the reference
notch on the knob corresponds with
the number or symbol for the cycle
you wish to set (have a look at the
wash cycle table on page 17).
After a few seconds, you will hear
a beep; the wash cycle has begun
and we do not recommend you
change it.
The dishwasher informs
you.
Your dishwasher is fitted with
indicator lights (G) which light up
to indicate the cycle phase under
way.
Here are the symbols correspond-
ing to each cycle phase:
pre-wash, wash, rinses, drying.
At all times, your dishwasher tells
you which cycle phase is under
way.
Modifying a wash cycle
in progress.
But if you have chosen the wrong
cycle, not to worry! You can modify
the wash cycle in progress, if it has
only just started. Turn the knob
anti-clockwise until it reaches the
Reset position and, after a few
seconds, a prolonged beep will
sound, followed by three short
beeps; the indicator light "G" will
turn off. This is to inform you that
all the settings have been
cancelled. You are now free to re-
set the correct wash cycle.
You've left out a dish?
Well, it happens to everyone. Inter-
rupt the wash cycle by pressing the
ON-OFF button, insert the dish you
had forgotten and press the ON-
OFF button again. The cycle will
start up from where you interrupted
it.
Finished?
The end of the wash cycle is indi-
cated by two short beeps and the
flashing of the drying phase indica-
tor light.
 Turn off the water tap.
 Wait a few minutes before unload-
ing the dishes: they are very
hot! If you wait a little while, they
dry better thanks to the steam.
 Empty the lower rack first
You decide when it
starts.
When you have loaded the dishes,
you can choose when to start your
dishwasher before setting the wash
cycle desired. Press button "D" to
delay the start of the wash cycle
by 12, 9, 6 or 3 hours. Each time
you press it, you will hear a short
beep and the indicator light "G"
corresponding to the selected
delay will light up.
Now you can select the desired
wash cycle. and after you hear the
beep, the countdown to the de-
layed start will begin.
Once this time is up, the indicator
light will stop flashing and the wash
cycle will begin.
If you have set a 12 hour delay, for
example, once you have selected
the wash cycle, the 12 hour
indicator light will flash followed
by the others in sequence until the
set time delay is up. A quick look
at the indicator lights will keep you
informed of the countdown
progress at all times.
Have you changed your
mind?
If you change your mind, you can
set a shorter time delay: press but-
ton "D" to select it. You need not
reset the wash cycle.
If on the other hand you want to
cancel the delay set and you want
the cycle to start immediately,
press button "D" repeatedly until
the cycle starts and indicator light
"G" corresponding to the cycle
start phase comes on.
If opening the
door soon after
the end of the
programme,or
during it, stand
away from the
Dishwasher, to
avoid possible
injury from hot
steam.
Make sure the
wash cycle has
ended before
removing the
dishes!
There's been a power
failure? Have you opened
the dishwasher door?
The wash cycle stops and then
restarts when the electricity comes
back on or when you shut the door.
Everything is under control!
Dual function of indicator
lights "G"
1) flashing to indicate a
delayed start: to remind you
that you have set a delayed start;
2) on and not flashing
beneath the cycle phase
symbol:
meaning the cycle has started and
is in the phase indicated by the
symbol.
Warning:
Turn the knob anti-clockwise
to Reset in order to reset all
the settings. Turn the
appliance off by pressing
button A, unplug the
appliance from the electricity
socket to cut off the power
supply; the power supply
cable should consequently be
easily accessible.