Instruction for Use

EN
25
Rinse aid and refined salt
Only use products which have been specifically
designed for dishwashers.
Do not use table salt or industrial salt, or washing
up liquid.
Follow the instructions given on the packaging.
If using a multi-functional product it is not necessary to add
rinse aid; however, we recommend that you add salt,
especially if you live in an area where the water is hard or
very hard. Follow the instructions given on the packaging.
If you do not add salt or rinse aid, the LOW SALT*
and LOW RINSE AID* indicator lights remain lit.
Measuring out the rinse aid
Rinse aid makes it easier for the crockery to dry, as water runs
off surfaces more readily and therefore does not leave streaks
or marks.
The rinse aid dispenser should be filled:
•WhentheLOWRINSEAID* indicator light on the control
panel/dislayisilluminated;
1.Openthedispenserbyturning
the lid (G) in an anticlockwise
direction.
2. Pour inthe rinseaid, making
sure it does not overflow from the
dispenser. If this happens, clean
the spill immediately with a dry
cloth.
3. Screw the lid back on.
NEVER pour the rinse aid directly into the appliance tub.
Adjusting the amount of rinse aid
If you are not completely satisfied with the drying results, you
mayadjustthequantityofrinseaidused.Useascrewdriverto
turn the dosage adjuster (F) to one of the 6 pre-set positions
(the default position is set to 4):
•Iftherearestreaksonthecrockery,settheadjustmentdevice
toalowernumber(1-3).
•Ifdropsofwaterremainonthecrockeryoriftherearelimescale
marks present after the cycle has finished, set the adjuster to
a higher number (4-6).
Setting the water hardness
Everydishwasherisequippedwithawatersoftenerwhich,by
using refined salt designed especially for this type of appliance,
supplies water without limescale which is then used to wash
the crockery.
This dishwasher offers a setting which helps to reduce pollution
and optimises washing performance in accordance with the
water hardness level in your area. This information can be
obtained from your local water supplier.
- Switch the machine off using the ON/OFF button and open
the door.
- Set the SELECT WASH CYCLE knob first to wash cycle 5,
then to wash cycle 1, then to wash cycle 5 again.
- Press the ON/OFF button; the wash cycle phase (washing,
drying, end) indicator lights will flash. It is now possible to select
the water hardness level. There is a water hardness level for
every wash cycle:
E.g.:washcycle1,waterhardnesslevel1
washcycle2,waterhardnesslevel2,etc.etc.,uptoamaximum
of 5* levels.
(The default water softener setting is level 3).
- To exit the function, wait a few seconds or press one of the op-
tion buttons*, or switch off the machine using the ON/OFF button.
Even if using multi-functional tablets, the salt dispenser should
still be filled.
(°dH=hardnessmeasuredinGermandegrees-°f=hardness
measuredinFrenchdegrees-mmol/l=millimolesperlitre)
Measuring out the refined salt
In order to achieve the best possible results using a wash
cycle, make sure that the dispenser is never empty. Refined salt
removes limescale from the water, thus avoiding the formation
of deposits on crockery.
The salt dispenser is located in the lower part of the dishwasher
(see Description) and should be filled:
•Whenthegreenfloat* cannot be seen by simply looking at
the cap of the salt dispenser.
•When theLOW SALT* indicatorlight on thecontrol panel/
display is illuminated;
1.Removethelowerrackandunscrewthe
container cap (anticlockwise).
2.Thefirsttimeyoudothis:fillthewatertank
right up to its edge.
3. Position the funnel* (see figure) and fill
the salt container right up to its edge (this
should hold approximately 1 kg); it is notunusual fora little
water to leak out.
4. Remove the funnel* and wipe any salt residue away from the
opening; rinse the cap under running water and then screw it
on, the head facing downwards so as to let the water flow out of
the four cracks which are arranged in a star shape on the lower
part of the cap. (Salt cap with green float*)
It is advisable to perform this procedure every time you add
salt to the container.
Make sure the cap is screwed on tightly, so that no detergent
can get into the container during the wash cycle (this could
damage the water softener beyond repair).
Whennecessary,measureoutthesaltbeforeawashcycle
so that any saline solution which has leaked out of the salt
dispenser is removed.
* Only available in selected models.
G
F
Water Hardness Table
Average salt container
capacity duration**
Level °dH °fH mmol/l months
1 0 - 6 0 - 10 0 - 1 7 months
2 6 - 11 11 - 20 1,1 - 2 5 months
3 12 - 17 21 - 30 2,1 - 3 3 months
4 17 - 34 31 - 60 3,1 - 6 2 months
5*
34 - 50 61 - 90 6,1 - 9 2/3 weeks
For values between 0°f and 10°f, we do not recommend the
use of salt. * this setting may cause a slight increase in the
duration of the cycles. ** for 1 wash cycle per day.