Installation Guide

29
ELECTRONIC CONTROL SETUP INSTRUCTIONS
Code Explanation
1. 00 MONEY COUNTER OPTION
This option is either NOT SELECTED “OFF”
or SELECTED “ON.”
1. 00 Not Selected “OFF.”
1. 0C Selected “ON.”
• Press the COLORS/DELICATES button
3 consecutive times to select “ON” and 3
consecutive times to deselect (Not Selected “OFF”).
Counter resets by going from “OFF” to “ON.”
1. C0 Selected “ON” and not able to be deselected.
• To select “ON” and not able to be deselected,
rst select “ON,” then within 2 seconds, press the
COLORS/DELICATES button twice, the COTTON/
WHITES button once, and exit set-up mode.
• Press the PERM PRESS button once to advance
to next code.
2. 00 This option is not available.
b. 30 VALUE OF COIN 1
b. 30 With coin slide activation, this represents the total
vend price in nickels. Example: b. 30 is equal to $1.50.
b. 05 This represents the value of coin 1 in number
of nickels: 05 = $0.25 (default for 9060 models).
• By pressing the COTTON/WHITES button, there is
an option of 1–199 nickels.
• Press the PERM PRESS button once to advance
to next code.
C. 20 VALUE OF COIN 2
C. 20 This represents the value of coin 2 in number
of nickels: 20 = $1.00.
• By pressing the COTTON/WHITES button, there is
an option of 1–199 nickels.
C. 05 When a Gen 2 card reader is used, this code represents
the value of top off in nickels. C. 05 = $0.25.
• Press the PERM PRESS button once to advance
to next code.
d. CS COIN SLIDE OPTION
This option is either Selected “ON” or Not Selected
“OFF.” Press the COLORS/DELICATES button 3
consecutive times to select/deselect this option.
d. CS Selected “ON.” (default for 9050 models)
When coin slide mode is selected, set “b.” equal to
value of vend price in nickels. Set set-up code 6 xx
(regular cycle price) to number of slide operations.
If the installer sets up “CS” on a coin drop operated
model, it will not register coins.
d. 00 Not Selected “OFF.” (default for 9060 models)
• Press the PERM PRESS button once to advance
to next code.
Code Explanation
J. Cd PAYMENT MODE (COIN/DEBIT OPTION)
J. Cd Both coin and debit selected. Press the COLORS/
DELICATES button 3 consecutive times to change
this selection.
J. C_ Coins selected, debit disabled. Press the COLORS/
DELICATES button 3 consecutive times to change
this selection.
J. _d Debit Card selected, coin disabled (default for 9060
models). This selection must be used for free vend.
Press the COLORS/DELICATES button 3 consecutive
times to change this selection.
J. Ed Enhanced Debit is self-selected when a Generation
2 card reader is installed in the dryer. The “Ed” option
cannot be manually selected or deselected.
• Press the PERM PRESS button once to advance
to next code.
n. CE CLEAR ESCROW OPTION
This option is either Selected “ON” or Not Selected
“OFF.” When selected, money held in escrow for 30
minutes without further escrow or cycle activity will
be cleared.
n. 00 Not Selected “OFF.”
n. CE Selected “ON.”
• Press the COLORS/DELICATES button once
to change this selection.
• Press the PERM PRESS button once to advance
to next code.
If cycle counter (9 0C) is selected, the following is true:
1 00 Cycles in HUNDREDS 1 02 = 200
2 00 Cycles in ONES 2 25 = 25
TOTAL CYCLES = 225
This is “VIEW ONLY” and cannot be cleared.
• Press the PERM PRESS button once to advance
to next code.
If money counter (1.0C or 1.C0) is selected, the following
is true:
3 00 Dollars in HUNDREDS 3 01 = $100.00
4 00 Dollars in ONES 4 68 = $ 68.00
5 00 Number of CENTS 5 75 = $ 00.75
TOTAL = $168.75
END of SET-UP PROCEDURES
TO EXIT FROM SET-UP MODE
1. Close the service access door.
2. Disconnect dryer from power before reinstalling the AA1
connector, if it was removed.
3. Remove the manual set-up card.