Instruction for Use

5019 300 00026
Load the laundry, close the door and add
detergents as indicated on the front page and
as described in the chapter “Detergent and
Additives” in your Instructions for Use.
• Turn the programme selector to the desired
programme and temperature.
• The indication lamp next to “Start(Pause)”
button blinks.
ADD DETERGENTS, CLOSE THE DOOR AND
SELECT THE PROGRAMME
SELECT ANY DESIRED OPTION
“DOOR OPEN” INDICATION
Before starting and after end of a programme, the
lamp lights to show the the door can be opened.
As long as a wash programme is running, the door
remains locked and must on no account be forced
open. In case you have an urgent need to open
it during a running programme, refer to “Cancel
(Reset) a running programme before the end”.
“Spin speed reduction” button
• Reduces the predetermined automatic
maximum spin speed to treat your laundry
more gently.
“Rinse hold” button
• The laundry remains in the last rinse water
without progressing to the final spin cycle to
avoid creasing and prevent colours from
changing.
• Particularly useful if you want to postpone
spinning to a later time, or if you want to drain
only.
• The programme stops to “Rinse hold” at the
time the “Rinse hold” indicator in the
programme flow bar is on. The indication lamp
next to the “Start(Pause)” button blinks.
Whirlpool is a registered trademark of Whirlpool USA.
PROGRAMME START
Open the tap and press the “Start(Pause)”
button. The indication lamp next to the “Start
(Pause)” button lights up. The programme flow
bar shows the current programme phase, running
from left to right through Wash, Rinse, Spin/Drain.
PROGRAMME END
• The “Door open” indication lights up.
1. Turn the programme selector to the “Off/O”
position.
2. Close the water tap.
3. Open the door and unload the machine.
4. Leave the door ajar to allow the drum to dry.
CHANGE PROGRAMME AND/OR OPTIONS
AFTER PROGRAMME START
1. Press the “Start(Pause)” button to pause the
programme. The light blinks.
2. Select the new programme (with temperature),
and any options if you want.
3. Press the “Start(Pause)” button again.
The new programme continues at the same
position where the previous programme was
interrupted. Do not add detergent for this
programme.
CANCEL (RESET) A RUNNING PROGRAMME
BEFORE THE END
The “Reset” button cancels a programme before
the end.
• Press and hold the “Reset” button for a few
seconds.
Any existing water is drained out. It may last
some time until the door can be opened.
Push the button of any option desired - the
respective indication lamp lights up.
If the combination of programme and additional
option(s) is not possible, the indication lights
switch off automatically.
FAILURE INDICATIONS
In case of any failures or irregularities, consult the
“Troubleshooting Guide” in your Instructions for
Use.
“Water tap closed”: no or not sufficient
inlet water.
”Service”: failure or malfunction of an
electrical component.
”Clean pump”: waste water is not pumped
out.
Spin speed blinks: unbalance during spinning.
CONSUMPTION DATA
Programme
Temperature
(°C)
Load
(kg)
Water
(l)
Energy
(kWh)
without
“Rapid”
Approx. programme
duration
(hours : minutes)
Cotton with prewash 95 7.0 84** 2.40 2:28
Cotton 60 7.0 54 1.19 2:20
Cotton
40
7.0 69
0.75 2:10
Synthetics with prewash 60 3.0 63** 1.00 1:53
Synthetics 60 3.0 50** 0.80 1:35
Synthetics
40
3.0 46
0.50 1:20
Delicates 30 1.5 60 0.50 0:46
Quick wash 30 3.0 45 0.30 0:30
Wool/Handwash 40 1.0 45 0.50 0:40
Wool/Handwash cold 1.0 45 0.10 0:35
Cotton * 60 7.0 54 1.05 4:00
Cotton * 60 3.5 40 0.85 3:00 ***
Cotton * 40 3.5 40 0.65 3:00
Consumption values were measured in normalized conditions, in compliance with IEC/EN 60456. In the home, they may vary depending on the individual
water supply pressure and temperature, the load and the type of wash. The consumption data indicated are based on an inlet water temperature of approx.
15°C through the cold fill valve as well as the hot fill valve (if available). If your washing machine has a hot fill valve, connection of this valve to hot water supply
will lower the energy consumption by reduced heating times, depending on the individual hot fill inlet water temperature. Water and energy consumptions
refer to the default setting of the programmes, with temperature and load as indicated in the table; selecting any options or changing the spin speed will also
change the consumption data.
The programme duration may differ from the values indicated above as it depends on the operation conditions applicable at that time (see also
“Troubleshooting Guide” in your Instructions for Use).
* Reference programmes for Energy Label. For reasons of energy saving, the real water temperature may deviate from the declared cycle temperature.
** To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains the water out.
*** Automatic adaptation of programme duration after detection of wash load
Power consumption in off-mode 0.11 W / in left-on mode 2.32 W
Terminate the “Rinse hold” option :
• Press the “Start/Pause” button ; the
programme will terminate automatically with
the final spin cycle for the present wash
programme.
• If you do not wish to spin the clothes, turn the
programme selector to the “Drain”
programme and press the “Start(Pause)”
button .