Instruction for Use

20
If the appliance must be moved at any time, keep it in an
upright position; if absolutely necessary, it may be tilted onto
its back.
Connecting the water supply
Adaptation of the water supply for installation should only
be performed by a qualified technician.
The water inlet and outlet hoses may be positioned towards
the right or the left in order to achieve the best possible
installation.
Make sure the dishwasher does not bend or squash the
hoses.
Connecting the water inlet hose
• Toa3/4”gascoldorhotwaterconnectionpoint(max.
60°C).
• Runthewateruntilitisperfectlyclear.
• Screwtheinlethosetightlyintopositionandturnoffthe
tap.
If the inlet hose is not long enough, contact a specialist
store or an authorised technician
(seeAssistance)
.
The water pressure must be within the values indicated
in the Technical Data table - otherwise the dishwasher may
be function properly.
Make sure the hose is not bent or compressed.
Connecting the water outlet hose
Connect the outlet hose to a drain duct with a minimum
diameterof2cm.(A)
The outlet hose connection must be at a height ranging from
40to80cmfromthefloororsurfacewherethedishwasher
rests.
Before connecting the water outlet hose to the sink drain,
removetheplasticplug(B).
Anti-flooding protection
To ensure floods do not occur, the dishwasher:
- is provided with a special system which blocks the water
supply in the event of anomalies or leaks from inside the
appliance.
Somemodels are alsoequipped with the supplementary
safety device New Acqua Stop, which guarantees anti-
flooding protection even in the event of a supply hose rupture.
WARNING: HAZARDOUS VOLTAGE!
Under no circumstances should the water inlet hose be cut
as it contains live electrical parts.
Electrical connection
Before inserting the plug into the electrical socket, make
sure that:
• The socket is earthed and complies with current
regulations;
the socket can withstandthe maximum load of the
appliance as shown on the data plate located on the inside
of the door
(seechapterDescriptionoftheappliance);
• Thepowersupplyvoltagefallswithinthevaluesindicated
on the data plate on the inside of the door.
• Thesocketiscompatiblewiththeplugoftheappliance.If
this is not the case, ask an authorised technician to replace
theplug(
see Assistance
).Donotuseextensioncablesor
multiple sockets.
Once the appliance has been installed, the power supply
cable and the electrical socket should be easily accessible.
The cable should not be bent or compressed.
If the power supply cable is damaged, have it replaced
by the manufacturer or its authorised Technical Assistance
Servicein order toprevent all potential hazards.
(See
Assistance)
The Company shall not be held responsible for any
incidents, if these regulations are not observed.
Positioning and levelling
1. Position the dishwasher on a level sturdy floor. If the floor is
uneven, the front feet of the appliance may be adjusted until
itreachesahorizontalposition.Iftheapplianceislevelled
correctly, it will be more stable and much less likely to move
or cause vibrations and noise while it is operating.
2. Before recessing the dishwasher, stick the adhesive
transparent strip under the wooden shelf in order to protect
it from any condensation which may form.
3.Place the dishwasher so that its sides or back panel
are in contact with the adjacent cabinets or the wall. This
appliance can also be recessed under a single worktop
(see
the Assembly instruction sheet)
.
4.Toadjusttheheightoftherearfoot,turntheredhexagonal
bushing on the lower central part at the front of the dishwasher
usingahexagonalspannerwithanopeningof8mm.Turnthe
spanner in a clockwise direction to increase the height and
in an anticlockwise direction to decrease it.
(seeBuilding-in
instruction sheet attached to the documentation)
Installation
MIN 40 cm
MAX 80 cm