Instruction for Use

ManualsBrandsWhirlpool ManualsDishwashersADL 558/2

-1-

Chart

PROGRAMME SELECTION BUTTON

Press button “P” (repeatedly) until the indicator of the required programme lights

up (see “Table of programmes” below).

BUTTON

OFF

BUTTON

START BUTTON

The indicator lights up during operation, flashes when a fault occurs and goes off at

the end of the programme.

START BUTTON RESET FUNCTION

Press this button for at least 2 seconds; the selected programme and options are

cancelled. Main failure displays (repeated flashing of the START indicator lamp) can

be cancelled by RESETTING. Detailed instructions are given in chapter “What to

do if...”.

1) Programme data obtained in conformity with European standard EN 50242, obtained under normal conditions (without additional

options) and may vary depending on conditions. Differences of up to 20 minutes are possible with sensor programmes as a result of

the appliance’s automatic calibration system.

2) Reference programme for energy label in compliance with EN 50242 regulations. - Note for Testing Institutes: for detailed information

on the EN/Standard loading comparison test and other tests, contact the following address: “nk_customer@whirlpool.com”.

Table of programmes

Detergent

Consumption

Programmes Loading instructions Litres kWh

Minutes

Pre-Wash cold

Crockery to be washed later. — 5.0 0.02 10

Quickwash 40°C

Lightly soiled crockery, with no

dried-on food. * Use of tablets not

recommended.

X * 13.0 0.70 30

Bio

50°C

Normally soiled crockery.

Energy-saving programme.

X 15.0 1.05 165

Daily 60°C

Normally or heavily soiled crockery. X 16.0 1.35 120

Intensive 70°C

Recommended programme for

heavily soiled crockery, especially

suitable for pots and pans.

X 17.0 1.65 145

5019 596 01515ADL 558

BEFORE USING THE APPLIANCE FOR THE

FIRST TIME CAREFULLY READ THIS QUICK

REFERENCE GUIDE AND THE INSTALLATION

INSTRUCTIONS! THE GUARANTEE IS NOT

APPLICABLE IF FAULTS ARE CAUSED BY

INCORRECT USE OF THE APPLIANCE.

Quick reference guide

Summary of content (8 pages)

PAGE 1
Chart Quick reference guide ON BUTTON PROGRAMME SELECTION BUTTON Press button “P” (repeatedly) until the indicator of the required programme lights up (see “Table of programmes” below). BEFORE USING THE APPLIANCE FOR THE FIRST TIME CAREFULLY READ THIS QUICK REFERENCE GUIDE AND THE INSTALLATION INSTRUCTIONS! THE GUARANTEE IS NOT APPLICABLE IF FAULTS ARE CAUSED BY INCORRECT USE OF THE APPLIANCE.
PAGE 2
First time use How to set detergent type: powder/gel/tablet (if option is available) In order to always ensure the best cleaning results, you NEED to set: DETERGENT type and WATER HARDNESS. 1. Select 3rd programme 2. Press START button 3a. Check your (see Table of programmes for 7 seconds detergent type... - page 1) Detergent types 3b....and set it on your dishwasher using the START button (as per table below) 4. Remember to use salt and rinse aid when needed (as indicated below) 5.
PAGE 3
Daily check Filling the salt reservoir - Dissolve limescale (not necessary if water hardness level is set to “soft”!) 1 The salt level indicator lamp may remain lit for the duration of several wash cycles. If the water hardness level falls within category (soft), no salt is required. Salt indicator (depending on the model) Visual indicator (depending on model). Screw on the cap. Salt residues around cap need to be removed. Add salt (never add detergent!). min. 1.5 kg max.
PAGE 4
How to load the racks How to load UPPER RACK 4 B - Adjustable flaps: In horizontal position for cups/long utensils, in raised position for plates and stemware. (In some models only) A - Multipurpose support: Different positions for long utensils, cups and glasses. How to adjust upper rack height (if available) - It could be useful to lift up upper rack to have more space in lower rack or bring it down to load long stem glasses.
PAGE 5
Select programme 6 Quick, permanent or alternating Overview of programmes The max. possible number of programmes is illustrated in this overview. The corresponding programmes for your appliance can be found on the panel (page 1). Choose programme according to the attached Programme Chart (page 1). Duration of the programme depends on the external conditions in the apartment, temperature and pressure etc. Wash cycle 7 The dishwasher door must be closed and the water tap open.
PAGE 6
What to do if... If a fault occurs, before restoring normal appliance operation.contacting the After-sales Service, make the following checks to try and remedy the problem. Most faults can be remedied by taking the following courses of action, quickly restoring normal appliance operation. The appliance... ...is not working/will not start ...shows “F1” on the display or the START indicator lamp flashes once ...shows “F4” on the display or the START indicator lamp flashes 4 times ...
PAGE 7
What to do if... Crockery and cutlery... ...salt indicator lit ...have deposits: regeneration salt residue ...are not dry Possible causes... Use tablets for soft water. - Set “Detergent type” option; if this option is not available, it is normal for the salt indicator to light up. - Water too hard. - In areas with very hard water, more regeneration salt needs to be added (see page 2 “How to set water hardness”). - Salt reservoir cap open. - Close the salt reservoir cap properly.
PAGE 8
What to do if... Disconnect the mains plug If, after carrying out the above checks, the fault persists, switch off the appliance, disconnect the mains plug and turn off the water tap. Contact the After-sales Service (see warranty).