Quick Start Guide

ManualsBrandsWhirlpool ManualsDishwasheradg 8527 ix

WH/II/B/GB

How to use the appliance

Further indications are given in the single chapters and in the user instructions.

Press the

/ OFF button.

(The first time you use the appliance

and when using a different type of

detergent)

1. Select the third programme from the

top in the relative table.

2. Press the Start button for about 7

seconds until the display changes.

3. Select the required detergent with

the Start button (OFF = powder

detergent, 2 in 1, 3 in 1, 4 in 1) (shown on the display).

4. Switch the appliance off and then switch it on again. The selected

detergent type will be shown on the display for approximately 3

seconds after switching on.

For dosage of powder detergent in compartment

and

refer to the

programmes table.

Mechanical indicator lamp

Electric indicator on control panel (if provided).

On models with water softener

system only.

Mechanical indicator lamp

. Electric

indicator on control panel (if provided).

Refer to the dishwasher loading instructions.

The last programme selected will light up.

Select the desired programme (using the specific button or knob).

The corresponding indicator lamp lights up.

If necessary (and if provided).

The corresponding indicator lamp lights up.

The selected programme is

then memorised (even in the

event of power failure).

- Only open the dishwasher if necessary

(Warning: beware of hot steam).

- If the appliance is switched off during a

wash cycle, when switched on again it

will resume the cycle from where it was

interrupted.

Only after the START button has switched off: Press the ON /

OFF

button.

All the indicator lamps switch off.

Warning: When the door is opened steam comes out!

Unload the appliance, starting from the lower rack.

Switch on the appliance

Select, save, and

supply the detergent

ABC

Check the rinse aid level

Check the

regeneration salt level

Load the racks

Close the dishwasher door,

turn on the water tap

Select a programme

Select additional options

Press the Start button

“Change programme in progress”

Press the START button for 2 sec. until the

Start indicator lamp switches off.

Select another programme and press the

START button again.

Wash cycle

Switch off the appliance

Turn off the water tap,

unload the racks

Summary of content (4 pages)

PAGE 1
How to use the appliance Further indications are given in the single chapters and in the user instructions. Switch on the appliance Select, save, and supply the detergent Check the rinse aid level Check the regeneration salt level Load the racks Press the ON / OFF button. (The first time you use the appliance and when using a different type of detergent) A BC 1. Select the third programme from the top in the relative table. 2. Press the Start button for about 7 seconds until the display changes. 3.
PAGE 2
Dishwasher loading instructions and racks provided Upper rack: depending on the model Multi-purpose support (A): 1) Depending on the position, for longhandles utensils, cups and glasses. May be used in three different positions. Crockery holders (B): Depending on the position, for example plates, cups and long-stemmed glasses. Revolving glass support (C): 2) Depending on the position, for example small or long-stemmed glasses. Long-handled utensils (e.g.
PAGE 3
What to do if... If a fault occurs, before contacting our After-Sales Service, make the following checks to try and remedy the problem (* see also the corresponding chapter in the user instructions). Problem The appliance is not working If crockery is not perfectly dry If crockery is not perfectly clean Cause Remedy • No water supply. • Open the tap. • The appliance does not load sufficient water. • Clean the water supply tap filter. • Ensure there are no kinks in the water hose.
PAGE 4
Before using the dishwasher, read the user instructions! GB Quick Reference Guide ADG 8527 Options 3) Programme selection button Time and failure display Indicates in hours the time remaining until the start of the wash cycle. Toward the end of the programme, during the drying cycle, the display will indicate the time remaining in minutes. “F....” Identification of faults for service technician “Delayed start” button The wash cycle can be programmed to start after 1 - 24 hours.