Instruction for Use

ManualsBrandsWhirlpool ManualsDishwashersADG 674 FD

-1-

Chart

PROGRAM SELECTION BUTTON

Press button “P” (repeatedly) until the indicator of the required program lights up (see “Table of

programs” below).

START BUTTON

The indicator lights up during operation, flashes when a fault occurs and goes off at the end of the program.

START BUTTON RESET FUNCTION

Press this button for at least 2 seconds; the selected program and options are cancelled. Main failure

displays (repeated flashing of the START indicator lamp) can be cancelled by RESETTING. Detailed

instructions are given in chapter “What to do, if...”.

BUTTON

OFF

BUTTON

1) Program data obtained in conformity with European standard EN 50242, obtained under normal conditions (without additional

options) and may vary depending on conditions. Differences of up to 20 minutes are possible with sensor programs as a result of th

appliance’s automatic calibration system.

2) Reference program for energy label in compliance with EN 50242 regulations. - Note for Testing Institutes: for detailed information on

the EN/Standard loading comparison test and other tests, contact the following address: “nk_customer@whirlpool.com”.

3) The antibacterial action has been tested by the Institut Pasteur of Lille (France), based on the NF EN 13697 standard of November 2001.

Table of programs

Deter-

gent

Consumption

Programs Loading instructions

Litres kWh

Minutes

Pre-Wash cold

Crockery to be washed later. — 4.0 0.03 14

Quickwash 45°C

Lightly soiled crockery, with no dried-on

food. * Use of tablets not

recommended.

X * 11.0 0.80 30

Eco

50°C

Normally soiled crockery.

Energy-saving program.

X 12.0 1.05 170

Antibacterial

Normally or heavily soiled crockery, with

additional antibacterial wash. Program

interruption (e.g. due to door opening)

can compromise elimination of germs.

X 13.0 1.50 115

Intensive 70°C

Recommended program for heavily

soiled crockery, especially suitable for

pots and pans.

X 14.0 1.55 155

5019 396 01907ADG 674

BEFORE USING THE APPLIANCE FOR THE

FIRST TIME CAREFULLY READ THIS QUICK

REFERENCE GUIDE AND THE ASSEMBLY

INSTRUCTIONS! THE GUARANTEE IS NOT

APPLICABLE IF FAULTS ARE CAUSED BY

INCORRECT USE OF THE APPLIANCE.

Quick reference guide

Summary of content (8 pages)

PAGE 1
Chart Quick reference guide PROGRAM SELECTION BUTTON Press button “P” (repeatedly) until the indicator of the required program lights up (see “Table of programs” below). ON BUTTON OFF BUTTON START BUTTON The indicator lights up during operation, flashes when a fault occurs and goes off at the end of the program. START BUTTON RESET FUNCTION Press this button for at least 2 seconds; the selected program and options are cancelled.
PAGE 2
First time use How to set detergent type: powder/gel/tablet (if option is available) In order to always ensure the best cleaning results, you NEED to set: DETERGENT type and WATER HARDNESS. 1. Select 3rd program (see 2. Press START button 3a. Check your Table of programs - page 1) for 7 seconds detergent type... Detergent types Powder or gel (factory setting) 3b....and set it on your dishwasher using the START button (as per table below) 4.
PAGE 3
Daily check Filling the salt reservoir - Dissolve limescale (not necessary if water hardness level is set to “soft”!) 1 Visual indicator (depending on model). Unscrew cap. Add salt (never add detergent!). min. 0.8 kg max. 1 kg Fill the salt reservoir with water before the first wash only. (depending on the model) Salt indicator on the control panel The salt level indicator lamp may remain lit for the duration of several wash cycles.
PAGE 4
How to load CUTLERY RACK 4 How to load LOWER RACK Position 1 Position 2 A - Two trays for cutlery E - Vertical plate holders: They can be folded down to load pots. E To allocate the cutlery rack in position 2 bring the upper rack down (see description below). How to remove cutlery rack and/or upper rack (if available) It could be useful to remove cutlery rack to load stem glasses in upper rack and/or remove upper rack to load bulky items in lower rack. Open the two retainers (D) to take off the rack.
PAGE 5
Select program 6 Overview of programs The max. possible number of programs is illustrated in the chapter “Chart”. The corresponding programs for your appliance can be found on the panel (page 1). Choose program according to the attached table of programs (page 1). Duration of the program depends on the external conditions in the apartment, temperature and pressure etc. Wash cycle 7 The dishwasher door must be closed and the water tap open.
PAGE 6
What to do if... If a fault occurs, before contacting the After-sales Service, make the following checks to try and remedy the problem. Most faults can be remedied by taking the following courses of action, quickly restoring normal appliance operation. The appliance... ...is not working/will not start ...shows “F1” on the display or the START indicator lamp flashes once ...shows “F4” on the display or the START indicator lamp flashes 4 times ...
PAGE 7
What to do if... Crockery and cutlery... ...salt indicator lit ...have deposits: regeneration salt residue ...are not dry Possible causes... Solutions... - Use tablets for soft water. - Set “Detergent type” option; if this option is not available, it is normal for the salt indicator to light up. - Water too hard. - In areas with very hard water, more regeneration salt needs to be added (see page 2 “How to set water hardness”). - Salt reservoir cap open. - Close the salt reservoir cap properly.
PAGE 8
Disconnect the mains plug What to do if... If, after carrying out the above checks, the fault persists, disconnect the mains plug and turn off the water tap. Contact the After-sales Service (see warranty). Before contacting our After-Sales Service, take note of the following: - the description of the fault, - the appliance type and model, - the service code (the number indicated on the adhesive rating plate) inside the door on the right-hand side: Precautions and general recommendations 1.