Instructions / Assembly

ManualsBrandsWG Wood Products ManualsBathNapa Valley 15.5 in. W x 43.5 in. H x 3.5 in. D Recessed Medicine Storage Cabinet in White

WG Wood Products

For additional help or to watch an installation video for in-the-wall

products, visit our website at www.wgwoodproducts.com

Installation Instructions

In-the wall Models

1. Measure the back of your unit or cut a template from scrap paper to those measurements, or in most cases, you can also use the

plastic toilet paper holder against the wall as a template. Place the template on the wall and trace around it with a pencil.

2. Use a stud finder to locate where the studs are in your wall. You’ll want your product to go between them. Use a drill to drill a

hole in each corner of the rectangle, then insert a drywall saw into each drilled hole and cut to the next one.

3. Using construction adhesive(such as Liquid Nails® Brand) found at any hardware store, apply a small bead all the way around the

outer edge of the back of the plastic toilet paper moldings .

4. Insert the plastic toilet paper holder into the hole and press it into place.

5. If desired, place a very thin bead of painter’s caulk around the outer edge to fill any small gaps due to uneven wall surfaces.

Summary of content (10 pages)

PAGE 1
WG Wood Products Installation Instructions For additional help or to watch an installation video for in-the-wall products, visit our website at www.wgwoodproducts.com In-the wall Models 1. Measure the back of your unit or cut a template from scrap paper to those measurements, or in most cases, you can also use the plastic toilet paper holder against the wall as a template. Place the template on the wall and trace around it with a pencil. 2. Use a stud finder to locate where the studs are in your wall.
PAGE 2
WG Wood Products Installation Instructions For additional help or to watch an installation video for in-the-wall products, visit our website at www.wgwoodproducts.com Door Assembly Instructions: If you have purchased any of our Convertible Doors (all except raised panel doors), you have the most versatile door on the market! The panel, be it wood, glass, or frosted glass will go into the back of the door frame using the vinyl strip provided.
PAGE 3
WG Wood Products Installation Instructions For additional help or to watch an installation video for in-the-wall products, visit our website at www.wgwoodproducts.com On-the wall Models (wall or surface mounted) 1. Most on the wall models use either a hardboard backer board which is pressed in place when screwed onto the wall (cabinets for instance), or a white posterboard backer which can be used to hide the wall behind a magazine or spice rack if desired.
PAGE 4
WG Wood Products For additional help or to watch an installation video for in-the-wall products, visit our website at www.wgwoodproducts.com Installation Instructions Photo A If your product has a door or hinges: Instructions for mounting your hinges 1. We do not pre=drill holes for hinges since we have found that hinge holes usually don’t line up exact anyway. A good rule of thumb is to mount the hinges about 1 or 2 inches from the top and bottom of the cabinet.
PAGE 5
WG Wood Products Installation Instructions For additional help or to watch an installation video for in-the-wall products, visit our website at www.wgwoodproducts.com If you have ordered optional concealed hinges: The Blum concealed hinges have two pieces to them (the hinge and the mounting plate). Begin by installing the hinges on the door. This is the piece with the round cup. There will be two Truss head screws (rounded head) to screw this into place.
PAGE 6
WG Wood Products Installation Instructions For additional help or to watch an installation video for in-the-wall products, visit our website at www.wgwoodproducts.com If your product has adjustable shelving: Adjustable Shelf Leveling Your product has been hand made to the highest quality possible. It is however, possible that your adjustable shelves may not sit perfectly level.
PAGE 7
WG Wood Products Installation Instructions For additional help or to watch an installation video for in-the-wall products, visit our website at www.wgwoodproducts.com If your product has a Tissue Dispenser: 1. There are two magnetic catches, two strike plates, 6 black screws ½” in length. Screw the magnetic latches into the sides of the unit using the ½” black screws. These should be about 1/8” to ¼” from the front of the frame to allow room for the faceplate.. See photo below.
PAGE 8
WG Wood Products Installation Instructions For additional help or to watch an installation video for in-the-wall products, visit our website at www.wgwoodproducts.com Curio Cabinets ONLY: 3. Attach the metal magnetic strike plate to the top of the glass to match up to the magnetic latch Peel and stick the foam to the glass by centering if over the edge of the glass and pressing it down on each side, then push the metal strike plate down on top of the foam. 1.
PAGE 9
WG Wood Products Installation Instructions For additional help or to watch an installation video for in-the-wall products, visit our website at www.wgwoodproducts.com Wall Mirror/ Mirror or Glass Door Assembly: In order to get your product to you safely, we may package things in different manners depending on the product involved, size, etc. Often times, we will pack mirrors or glass in a separate box of their own.
PAGE 10
Instructions for assembling Sliding Door Cabinets Place the slide on the cabinet box first. The end of the slide (the part that slides out) needs to be even with the edge of the cabinet box on whichever side you intend to have the door slide to. So if you’re going to slide it open Left, you’ll place the slides on so that the opening end of the slide that opens is even with the left side frame of the cabinet.