ETL-ES-Vintage-WH19 OWNER'S MANUAL MANUAL DEL USUARIO Vintage Please write model number here for future reference: Por favor, incluya el número del modelo aquí para futura referencia: Net Weight: Peso Neto: 16.10 LBS 7.
ETL-ES-Vintage-WH19 SAFETY TIPS OBSERVE THE FOLLOWING: READ AND SAVE THESE INSTRUCTIONS WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR PERSONAL INJURY, MOUNT TO OUTLET BOX MARKED 'ACCEPTABLE FOR FAN SUPPORT OF 35 LBS (15.9 KG) OR LESS' AND USE MOUNTING SCREWS PROVIDED WITH THE OUTLET BOX AND/OR SUPPORT DIRECTLY FROM BUILDING STRUCTURE. MOST OUTLET BOXES COMMONLY USED FOR THE SUPPORT OF LUMINARIES ARE NOT ACCEPTABLE FOR FAN SUPPORT AND MAY NEED TO BE REPLACED.
ETL-ES-Vintage-WH19 CONSEJOS DE SEGURIDAD HAGA LO SIGUIENTE: LEA Y GUARDE ESTAS INSTRUCCIONES ADVERTENCIA: PARA REDUCIR EL RIESGO DE INCENDIO, DESCARGA ELÉCTRICA O HERIDAS GRAVES PERSONALES, MONTE EN UNA CAJA DE EMBUTIR ROTULADA “ADECUADA PARA VENTILADORES DE 35 LBS (15,9 KG) O MENOS” UTILIZANDO LOS TORNILLOS DE MONTAJE INCLUIDOS CON LA CAJA DE EMBUTIR Y/O MONTE DIRECTAMENTE EN LA ESTRUCTURA DEL EDIFICIO.
ETL-ES-Vintage-WH19 FEATURES CARACTERÍSTICAS FLUSH MOUNT INSTALLATION INSTALACIÓN AL TECHO DOWNROD INSTALLATION INSTALACIÓN CON VARILLA VERTICAL SLOPED CEILING INSTALLATION INSTALACIÓN PARA TECHO INCLINADOS For low ceilings Para techo bajos For normal ceilings Para techo normales May require a longer downrod (sold separately) Podría requerir una varilla vertical más larga (se vende por separado) Note: For sloped ceiling installation, please refer to westinghouselighting.
ETL-ES-Vintage-WH19 FEATURES CARACTERÍSTICAS COMBO-BLADE Combo-Blades feature two high quality finishes on one blade. Select the one that best complements your decor, or change the style with just a flip of the blade. NOTE: Combo-Blade finishes vary, depending upon model. ALETAS DE DOBLE CARA Las aletas del rotor de doble cara presentan dos superficies con un acabado de alta calidad.
ETL-ES-Vintage-WH19 PREPARING FOR INSTALLATION ANTES DE LA INSTALACIÓN 1 2 Unpack and inspect fan carefully to be certain all contents are included. Turn off power at fuse box to avoid possible electrical shock. Use metal outlet box suitable for fan support (must support 35 lbs). Before attaching fan to outlet box, ensure the outlet box is securely fastened by at least two points to a structural ceiling member (a loose box will cause the fan to wobble).
ETL-ES-Vintage-WH19 MOUNTING BRACKET INSTALLATION INSTALACIÓN CON SOPORTE DE MONTAJE 3 1 2 1 2 Remove the screws and star washers from the two mating holes (1) on the canopy. Loosen (do not remove) the screws in the mating slots (2) on the canopy. Rotate the mounting bracket clockwise and remove from the canopy. Quite los tornillos y las dos arandelas en estrella de los dos agujeros coincidentes (1) del dosel. Afloje (no quite) los tornillos de las ranuras coincidentes (2) del dosel.
ETL-ES-Vintage-WH19 MOUNTING BRACKET INSTALLATION INSTALACIÓN CON SOPORTE DE MONTAJE MOUNTING OPTIONS OPCIONES DE MONTAJE 4 5 Choose a MOUNTING OPTION Elija una OPCIÓN DE MONTAJE FLUSH MOUNT OPTION If flush mount option is selected, proceed to page 9, step 6. OPCIÓN DE INSTALACIÓN AL RAS Si elige la opción de montaje al ras, proceda a la página 9, paso 6. NORMAL DOWNROD OPTION If installing downrod supplied with fan, proceed to page 10, step 8.
ETL-ES-Vintage-WH19 FLUSH MOUNT OPTION OPCIÓN DE INSTALACIÓN AL RAS 7 6 For flush mount option, raise fan assembly and place onto hook from mounting bracket into a closed hole on the canopy. This will allow for hands free wiring. PROCEED DIRECTLY TO PAGE 14 FOR WIRING OPTIONS. Para la opción de montaje al ras, levante el montaje del ventilador, colóquelo sobre el gancho de la placa de montaje y cuélguelo en uno de los agujeros cerrados del dosel.
ETL-ES-Vintage-WH19 NORMAL DOWNROD OPTION OPCIÓN CON VARILLA VERTICAL PARA CIELORRASO NORMAL 8 EXTENDED DOWNROD OPTION OPCIÓN CON VARILLA VERTICAL MÁS LARGA 9 2 3 3 1 Feed motor lead wires through downrod/canopy assembly and insert downrod into downrod yoke. Make sure to align hole in downrod with the hole in downrod yoke. Install yoke cross pin (1) through yoke and downrod. Insert clamp pin (2) into cross pin until it snaps into place. Tighten set screws (3) in yoke. PROCEED TO PAGE 13, STEP 13.
ETL-ES-Vintage-WH19 EXTENDED DOWNROD OPTION OPCIÓN CON VARILLA VERTICAL MÁS LARGA 10 2 1 Slide downrod ball (1) off of downrod and remove pin (2). Deslice la esfera de la varilla vertical (1) hasta separarla de la varilla vertical y quite el pasador (2). 11 Re-install pin into extended downrod, and slide downrod ball up to the top of the downrod. Re-install set screw to secure ball to downrod. Note: Some extended downrods have a pre-drilled set-screw hole.
ETL-ES-Vintage-WH19 EXTENDED DOWNROD OPTION OPCIÓN CON VARILLA VERTICAL MÁS LARGA 12 2 3 1 Feed motor lead wires through downrod/canopy assembly and insert downrod into downrod yoke. Make sure to align hole in downrod with the hole in downrod yoke. Install yoke cross pin (1) through yoke and downrod. Insert clamp pin (2) into cross pin until it snaps into place. Tighten set screws (3) in yoke.
ETL-ES-Vintage-WH19 MOUNTING MONTAJE 13 14 Carefully lift fan assembly onto mounting bracket. Rotate fan until notch on downrod ball (1) engages the ridge on the mounting bracket (2). This will allow for hands free wiring. Levante con cuidado el conjunto del ventilador hasta el soporte de montaje. Gire el ventilador hasta que la muesca de la bola de la varilla vertical (1) calce sobre la saliente del soporte de montaje (2). De este modo, tendrá las dos manos libres para hacer el cableado.
ETL-ES-Vintage-WH19 WIRING OPTIONS OPCIÓN DE CABLEADO 15 PULL CHAIN WIRING OPTION WALL CONTROL WIRING OPTION 16 Follow diagram above to make wiring connections for fan pull chain control. Follow diagram above to make wiring connections for wall control operation.
ETL-ES-Vintage-WH19 SECURE TO CEILING ASEGURE EL VENTILADOR AL TECHO 17 For flush mount fans, carefully lift fan from the mounting bracket, making sure not to break any wire connections. For downrod fans, slide the canopy up to the mounting bracket. Para ventiladores de instalación al ras, levante con cuidado el ventilador del soporte de montaje asegurándose de que no interrumpa ninguna conexión de los cables.
ETL-ES-Vintage-WH19 BLADE INSTALLATION INSTALACIÓN DE LAS ALETAS 19 18 2 2 1 1 2 Check the motor for plastic shipping stabilizer tabs (1), and remove them if they are present. Attach blade assembly to motor using the noise-dampening motor gaskets (2) and motor screws provided. Tighten screws securely. NOTE: Some models do not utilize motor gaskets, washers, or stabilizer tabs. Verifique si hay lengüetas plásticas de embalaje para sostener al motor (1) y descártelas.
ETL-ES-Vintage-WH19 20 LIGHT FIXTURE INSTALLATION INSTALACIÓN DEL ARTEFACTO LUMINOSO 21 22 Find the two wires from the switch housing with the tag that says FOR LIGHT. Connect the black wire from the switch housing to the black wire from the light kit, and connect the white wire from the switch housing to the white wire from the light kit with wire nuts provided. Attach light kit to the switch housing using three small screws provided.
ETL-ES-Vintage-WH19 OPERATION AND MAINTENANCE Operation Turn on the power and check operation of fan. The pull chain controls the fan speeds as follows: 1 pull - high; 2 pulls - medium; 3 pulls - low; 4 pulls - off. Speed settings for warm or cool weather depend on factors such as room size, ceiling height, number of fans and so on. The slide switch controls direction, forward or reverse. Warm weather/down position - (Forward) Fan turns counterclockwise direction.
ETL-ES-Vintage-WH19 OPERACIÓN Y MANTENIMIENTO Operación Encienda el ventilador y verifique su funcionamiento. La cadenilla de tiro controla las velocidades del ventilador de la siguiente manera: 1 jalón – rápida; 2 jalones - mediana; 3 jalones - lenta; 4 jalones - apagado. Las velocidades para clima cálido o frío dependen de factores como el tamaño de la habitación, la altura del ventilador, el número de ventiladores, etc.
ETL-ES-Vintage-WH19 TROUBLESHOOTING GUIDE If you have difficulty operating your new ceiling fan, it may be the result of incorrect assembly, installation, or wiring. In some cases, these installation errors may be mistaken for defects. If you experience any faults, please check this troubleshooting chart. If a problem cannot be remedied, please consult with your qualified electrician and do not attempt any electrical repairs yourself. TROUBLE SUGGESTED REMEDY 1. If fan does not start: 1.
ETL-ES-Vintage-WH19 GUÍA PARA SOLUCIONAR PROBLEMAS Si tiene dificultades para hacer funcionar su nuevo ventilador, podría ser a causa del armado, instalación o cableado incorrectos. En algunos casos, estos errores de instalación podrían ser confundidos con defectos. Si experienca algun fallo, consulte esta guía para solucionar problemas. Si no puede solucionar el problema, consulte a un electricista calificado y no intente reparar conexiones eléctricas. PROBLEMA SOLUCIÓN SUGERIDA 1.
ETL-ES-Vintage-WH19 WARRANTY This Westinghouse Lighting Fan offers a Limited Lifetime Warranty to the original owner against defects in material and workmanship. This warranty is in lieu of all other warranties expressed or implied. Westinghouse Lighting will repair or replace the parts needed, and/or, replace the ceiling fan, if the defective is due to faulty materials or workmanship. Years 1 & 2 – Westinghouse Lighting will repair or replace this ceiling fan.
ETL-ES-Vintage-WH19 PARTS LIST LISTA DE REPUESTOS # Description 1 1 . . . . . . . . . . . . . . . . . . . . . Mounting Bracket 2 . . . . . . . . . . . . . . . . . . . . . Blade Bracket 3 . . . . . . . . . . . . . . . . . . . . . Blade 4 . . . . . . . . . . . . . . . . . . . . . Glass 5 . . . . . . . . . . . . . . . . . . . . . Fan Speed Switch 6 . . . . . . . . . . . . . . . . . . . . . Light Control Switch 7 . . . . . . . . . . . . . . . . . . . . . Capacitor 8 . . . . . . . . . . . .
ETL-ES-Vintage-WH19 Westinghouse Lighting, Philadelphia, PA 19154-1029, U.S.A. www.westinghouselighting.com , WESTINGHOUSE, and INNOVATION YOU CAN BE SURE OF are trademarks of Westinghouse Electric Corporation. Used under license by Westinghouse Lighting All rights reserved.
