ETL-ES-Zander-R-WH14 Owner's Manual Manual del usuario Zander Please write model number here for future reference: / Por favor, incluya el número del modelo aquí para futura referencia: Net Weight: Peso Neto: 16.68 LBS 7.
ETL-ES-Zander-R-WH14 Safety tips OBSERVE THE FOLLOWING: READ AND SAVE THESE INSTRUCTIONS WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR PERSONAL INJURY, MOUNT TO OUTLET BOX MARKED 'ACCEPTABLE FOR FAN SUPPORT OF 15.9 KG (35 LBS) OR LESS' AND USE MOUNTING SCREWS PROVIDED WITH THE OUTLET BOX AND/OR SUPPORT DIRECTLY FROM BUILDING STRUCTURE. MOST OUTLET BOXES COMMONLY USED FOR THE SUPPORT OF .LUMINARIES ARE NOT ACCEPTABLE FOR FAN SUPPORT AND MAY NEED TO BE REPLACED.
ETL-ES-Zander-R-WH14 Consejos de seguridad HAGA LO SIGUIENTE: LEA Y GUARDE ESTAS INSTRUCCIONES ADVERTENCIA: PARA REDUCIR EL RIESGO DE INCENDIO, DESCARGA ELÉCTRICA O HERIDAS GRAVES PERSONALES, MONTE EN UNA CAJA DE EMBUTIR ROTULADA “ADECUADA PARA VENTILADORES DE 15,9 KG (35 LB) O MENOS” UTILIZANDO LOS TORNILLOS DE MONTAJE INCLUIDOS CON LA CAJA DE EMBUTIR Y/O MONTE DIRECTAMENTE EN LA ESTRUCTURA DEL EDIFICIO LA MAYORÍA DE LAS CAJAS DE EMBUTIR UTILIZADAS .
ETL-ES-Zander-R-WH14 Features Características DOWNROD INSTALLATION instalación con varilla vertical For normal ceilings Para techo normales 4
ETL-ES-Zander-R-WH14 Features Características COMBO-BLADE Combo-Blades feature two high quality finishes on one blade. Select the one that best complements your decor, or change the style with just a flip of the blade. NOTE: Combo-Blade finishes vary, depending upon model. ASPAS DE DOBLE CARA Las aspas del rotor de doble cara presentan dos superficies con un acabado de alta calidad. Invirtiendo las aspas puede Ud.
ETL-ES-Zander-R-WH14 pREPARING for installation Antes de la instalación 1 2 Unpack and inspect fan carefully to be certain all contents are included. Turn off power at fuse box to avoid possible electrical shock. Use metal outlet box suitable for fan support (must support 35 lbs). Before attaching fan to outlet box, ensure the outlet box is securely fastened by at least two points to a structural ceiling member (a loose box will cause the fan to wobble).
ETL-ES-Zander-R-WH14 Mounting bracket Installation Instalación con soporte de montaje 3 4 1 Loosen but don’t remove the screws at the bottom of canopy; remove the mounting bracket from the canopy. Install mounting bracket (1) to outlet box in ceiling using the screws and washers provided with the outlet box. Afloje pero no quite los tornillos en la parte inferior del dosel; extraiga el soporte de montaje del dosel.
ETL-ES-Zander-R-WH14 MOUNTING OPTIONS OPCIONES DE MONTAJE 5 6 Choose a MOUNTING OPTION Elija una OPCIÓN DE MONTAJE NORMAL DOWNROD OPTION If installing downrod supplied with fan, proceed to page 8, step 6. OPCIÓN CON VARILLA VERTICAL PARA TECHO NORMAL Si instala la varilla vertical incluida con el ventilador, proceda a la página 8, paso 6. 3 EXTENDED DOWNROD OPTION If installing with longer downrod than supplied with fan, proceed to page 11, step 9.
ETL-ES-Zander-R-WH14 NORMAL DOWNROD OPTION OPCIÓN CON VARILLA VERTICAL PARA techo NORMAL 7 1 2 3 Place downrod assembly (1) into canopy (2) and coupling cover (3). Feed motor wires though the downrod assembly (1). Coloque el conjunto de la varilla vertical (1) dentro del dosel (2) y la cubierta del acoplamiento (3).Pase los cables del motor a través del conjunto de la varilla vertical (1).
ETL-ES-Zander-R-WH14 NORMAL DOWNROD OPTION OPCIÓN CON VARILLA VERTICAL PARA techo NORMAL 8 2 1 3 4 Insert downrod into downrod coupling. Make sure to align hole in downrod with the hole in downrod coupling. Install cross pin (1) through coupling and downrod. Insert keeper pin (2) into cross pin until it snaps into place. Tighten set screws (3) in coupling. Slide coupling cover (4) over the downrod coupling. PROCEED TO PAGE 15, STEP 15.
ETL-ES-Zander-R-WH14 EXTENDED DOWNROD OPTION OPCIÓN CON VARILLA VERTICAL MÁS LARGA 10 9 3 2 1 1 2 Slide downrod ball (1) off of downrod and remove pin (2). Deslice la bola de la varilla vertical (1) hasta separarla de la varilla vertical y quite el pasador (2). Loosen downrod ball (1) from downrod (2) by removing set screw (3). Afloje la bola de la varilla vertical (1) de la varilla vertical (2) quitando el tornillo (3).
ETL-ES-Zander-R-WH14 EXTENDED DOWNROD OPTION OPCIÓN CON VARILLA VERTICAL MÁS LARGA 11 Re-install pin into extended downrod, and slide downrod ball up to the top of the downrod. Re-install set screw to secure ball to downrod. Note: Some extended downrods have a pre-drilled set-screw hole. If a pre-drilled hole is present in the extended downrod, tighten the set screw into the pre-drilled hole in the extended downrod.
ETL-ES-Zander-R-WH14 BLADE INSTALLATION INSTALACIÓN DE LAS aletas 12 Remove the two screws holding the decorative cover to the top of the motor housing. This will allow access for securing the blades to the motor. Quite los dos tornillos que sujetan la cubierta decorativa de la parte superior del alojamiento del motor. Esto permitirá el acceso para fijar las aletas al motor.
ETL-ES-Zander-R-WH14 BLADE INSTALLATION INSTALACIÓN DE LAS aletas 14 13 Insert the blades through the slots on the motor housing as shown, and use the provided blade screws and fabric washers to tighten the blades to the preattached blade brackets. Replace the decorative cover onto the top of the motor housing, securing with the two screws previously removed.
ETL-ES-Zander-R-WH14 MOUNTING MONTAJE 15 Carefully lift fan assembly onto mounting bracket. Rotate fan until notch on downrod ball (1) engages the ridge on the mounting bracket (2). This will allow for hands free wiring. Levante con cuidado el conjunto del ventilador hasta el soporte de montaje. Gire el ventilador hasta que la muesca de la bola de la varilla vertical (1) enganche sobre la saliente del soporte de montaje (2). De este modo, tendrá las dos manos libres para hacer el cableado.
ETL-ES-Zander-R-WH14 wiring OPTIONS OPCIÓN DE CABLEADO 17 16 Once wiring step has been completed, slide the wired remote receiver in between the mounting bracket and the top of the downrod ball for downrod fans. Make wiring connections from the house and the motor to the remote receiver as shown above. Connect using wire nuts (provided).
ETL-ES-Zander-R-WH14 Secure To Ceiling Asegure el ventilador al techo 18 Loosen the 2 screws on the bottom of mounting bracket. (do not remove) Raise the canopy up and align the keyholes on the bottom of the canopy with the 2 screws on the bottom of mounting bracket. Rotate the canopy until both screws from the mounting bracket drop into the slot recesses. Tighten screws securely. Afloje los 2 tornillos de la parte inferior del soporte de montaje (no los extraiga completamente).
ETL-ES-Zander-R-WH14 LiGHt FiXtUrE inStaLLatiOn Instalación del artefacto luminoso 19 20 Locate the indentations on the neck of the glass and align with the protrusions on the inside of the light kit. Lift the glass up allowing the protrusions to engage the indentations of the glass, and twist the glass clockwise to lock into place. Localice las marcas en el cuello de la pantalla de vidrio y alinéelas con las protuberancias en el interior del juego de luces.
ETL-ES-Zander-R-WH14 21 22 OFF HI D ME LO Mount wall bracket to the wall using screws provided. Place the transmitter into the mounted holder. Instale el soporte de pared sobre la pared con los tornillos incluidos. Coloque el transmisor en el soporte montado.
ETL-ES-Zander-R-WH14 23 OFF HI MED LO ON 1 Remote Control Operation NOTE: This remote is to use 2 x AAA batteries. This remote control is preset up a pair of codes when being manufactured. After install the unit and restore the power of your fan, press and hold the “OFF” button for 5 seconds. You must press the “OFF” button within 60 seconds of restoring power to the fan. After hearing 4 short beep sounds, the speed setting process is completed. 1.
ETL-ES-Zander-R-WH14 OPEratiOn and MaintEnanCE Operation Turn on the power and check operation of fan. Speed settings for warm or cool weather depend on factors such as room size, ceiling height, number of fans and so on. The reverse switch in remote transmitter controls direction, forward or reverse. Warm weather/down position - (Forward) Fan turns counterclockwise direction. A downward air flow creates a cooling effect as shown in illustration A.
ETL-ES-Zander-R-WH14 Operación y mantenimiento Operación Encienda el ventilador y verifique su funcionamiento. Las velocidades para clima cálido o frío dependen de factores como el tamaño de la habitación, la altura del ventilador, el número de ventiladores, etc. El interruptor de marcha atrás del transmisor remoto controla la dirección, ya sea marcha adelante o marcha atrás. Clima cálido/posición hacia abajo - (Adelante) El ventilador gira en sentido contrahorario.
ETL-ES-Zander-R-WH14 trOUBLESHOOtinG GUidE If you have difficulty operating your new ceiling fan, it may be the result of incorrect assembly, installation, or wiring. In some cases, these installation errors may be mistaken for defects. If you experience any faults, please check this Trouble Shooting chart. If a problem cannot be remedied, please consult with your authorized electrician and do not attempt any electrical repairs yourself. TROUBLE SUGGESTED REMEDY 1. If fan does not start: 1.
ETL-ES-Zander-R-WH14 GUía Para SOLUCiOnar PrOBLEMaS PROBLEMA Si tiene dificultades para hacer funcionar su nuevo ventilador, podría ser a causa del armado, instalación o cableado incorrectos. En algunos casos, estos errores de instalación podrían ser confundidos con defectos. Si experienca algun fallo, consulte esta guía para solucionar problemas. Si no puede solucionar el problema, consulte a un electricista calificado y no intente reparar conexiones eléctricas. SOLUCIÓN SUGERIDA 1.
ETL-ES-Zander-R-WH14 PARTS LIST LISTA DE REPUESTOS # Description 1 1 . . . . . . . . . . . . . . . . . . . . . Mounting Bracket (1) 2 . . . . . . . . . . . . . . . . . . . . . Blade (5) 3 . . . . . . . . . . . . . . . . . . . . . Glass (1) 4 . . . . . . . . . . . . . . . . . . . . . Remote Control (1) 5 . . . . . . . . . . . . . . . . . . . . . Hardware Pack (1) 2 No. Descripción 1 . . . . . . . . . . . . . . . . . . . . .Soporte de montaje (1) 2 . . . . . . . . . . . . . . . . . . . .
ETL-ES-Zander-R-WH14 26
ETL-ES-Zander-R-WH14 27
ETL-ES-Zander-R-WH14 Westinghouse Lighting, Philadelphia, PA 19154-1029, U.S.A. www.westinghouselighting.com , WESTINGHOUSE, and INNOVATION YOU CAN BE SURE OF are trademarks of Westinghouse Electric Corporation. Used under license by Westinghouse Lighting All rights reserved.
