Product Manual A

ManualsBrandsWerner ManualsTools & HardwareUpgear Blue Armor 2000 Construction (3 D-Rings) Medium/Large Harness

WARNING!

Compliant fall protection equipment must only be used as it was designed. Users MUST read and follow

all user instructions provided with the product. Before using a fall arrest system, users must be trained in

the safe use of the system, as required by OSHA 29 CFR 1910.30 and 1926.503, or local safety regulations.

Misuse or failure to heed these warnings and instructions may result in injury or even death.

WORK SAFE! WORK SMART!

FULL BODY HARNESS

Complies with the ANSI Z359.11 standard and OSHA 29 CFR 1910 and 1926 regulations.

USER INSTRUCTIONS

IF YOU HAVE ANY QUESTIONS ABOUT THE PROPER USE OF THE EQUIPMENT, SEE YOUR SUPERVISOR, USER

INSTRUCTIONS, OR CONTACT WERNER CO. FOR MORE INFORMATION.

(This manual applies to all harnesses with model numbers starting with H0, H1, H2, H3 and H9)

Summary of content (8 pages)

PAGE 1
USER INSTRUCTIONS FULL BODY HARNESS Complies with the ANSI Z359.11 standard and OSHA 29 CFR 1910 and 1926 regulations. (This manual applies to all harnesses with model numbers starting with H0, H1, H2, H3 and H9) WARNING! Compliant fall protection equipment must only be used as it was designed. Users MUST read and follow all user instructions provided with the product. Before using a fall arrest system, users must be trained in the safe use of the system, as required by OSHA 29 CFR 1910.30 and 1926.
PAGE 2
USE INSTRUCTIONS AND LIMITATIONS IMPORTANT Before use, the user must read and understand these User Instructions. Keep these User Instructions for reference. PURPOSE The Full Body Harness is designed to be used as part of a complete personal fall arrest, restraint, rescue, ladder climbing, or work positioning system. USE INSTRUCTIONS 1. 2. 3. 4. 5. 6. 7. Failure to follow all instructions and limitations on the use of the Full Body Harness may result in serious personal injury or death.
PAGE 3
10. TRAINING: Do not use the Full Body Harness without proper training from a “competent person” as defined by OSHA 29 CFR 1910.140(b) and 1926.32(f). 11. REPAIRS: Only Werner Co., or persons or entities authorized in writing by Werner Co., may make repairs or alterations to the equipment. ANCHORAGES All anchorage requirements depend on the application which the Full Body Harness is used. In a personal fall arrest system the anchorage must meet the requirements of OSHA 29 CFR 1910 and 1926.
PAGE 4
. Fasten the chest strap across the lower chest just below the nipple line. Chest strap should be snug, with excess strap secured through the web keepers. FITTING Adjust shoulder straps with the two adjusters located at the lower end of the shoulder strap. Adjust the left and right sides to the same length. The chest strap, and front (sternal) D-ring if applicable, must be centered on your lower chest.
PAGE 5
RELIEF CORDTM / RELIEF HANDLES The ProForm Full Body Harness is equipped with the Relief Cord and all others are equipped with Relief Handles. Both are designed to help with the discomfort of suspension after a fall occurs. To use the Relief Cord / Relief Handles: 1. Slide Chest strap down away from the throat, by grabbing the lanyard keeper and pulling down. 2. Grab the relief cord handles and pull out and forward, while lifting legs to a seated position. 3. Readjust chest strap down away from the throat.
PAGE 6
5. Suspension intolerance, also called suspension trauma or orthostatic intolerance, is a serious condition that can be controlled with good harness design, prompt rescue and post fall suspension relief devices. A conscious user may deploy a suspension relief device allowing the user to remove tension from around the legs, freeing blood flow, which can delay the onset of suspension intolerance.
PAGE 7
14. WAIST, REAR – The waist, rear attachment shall be used solely for travel restraint. The waist, rear attachment element shall not be used for fall arrest. Under no circumstances is it acceptable to use the waist, rear attachment for purposes other than travel restraint. The waist, rear attachment shall only be subjected to minimal loading Class P through the waist of the user, and shall never be used to support the full weight of the user. 15.
PAGE 8
LABELS 130-310 lbs. ANSI Z359.11-2014 Etiquetas 1 2 3 4 5 6 7 8 9 10 11 12 Year Year Year Year Year Año 1 Año 2 Año 3 Año 4 Año 5 Serial Number: Número de serie: Inspection Log/Registro de Inspección Assembled in: Ensamblas en: Mark Number/Número de Mark de 1 Capacidad de peso (OSHA): hasta 400 libras. PEQUEÑO ANSI Z359 Recognizes the use of this harness only within the capacity range of: P/N110358-01 Rev A 9/16 Labels Weight capacity (OSHA): up to 400 lbs.