DRYWALL SANDER Model # 6369 bit.ly/wenvideo IMPORTANT: Your new tool has been engineered and manufactured to WEN’s highest standards for dependability, ease of operation, and operator safety. When properly cared for, this product will supply you years of rugged, trouble-free performance. Pay close attention to the rules for safe operation, warnings, and cautions. If you use your tool properly and for intended purpose, you will enjoy years of safe, reliable service.
TABLE OF CONTENTS Technical Data General Safety Rules Specific Safety Rules For Drywall Sanders Electrical Information Know Your Drywall Sander Troubleshooting Assembly Operation Maintenance Exploded View and Parts List Warranty 2 3 4 5 6 6 7 7 8 9 11 TECHNICAL DATA Model Number: Motor: Speed: Hook & Loop Base Diameter: Shortened Length: Length with Extension: Sanding Pad Diameter: Sanding Pad Grits: Dust Port Sizes: Net Weight: 2 6369 120 V, 60 Hz, 5A 600 to 1500 RPM (no load) 8.5 inches 43.
GENERAL SAFETY RULES Safety is a combination of common sense, staying alert and knowing how your item works. SAVE THESE SAFETY INSTRUCTIONS. WARNING: To avoid mistakes and serious injury, do not plug in your tool until the following steps have been read and understood. 1. READ and become familiar with this entire instruction manual. LEARN the tool’s applications, limitations, and possible hazards. 2. AVOID DANGEROUS CONDITIONS. Do not use power tools in wet or damp areas or expose them to rain.
GENERAL SAFETY RULES 15. DO NOT OVERREACH. Keep proper footing and balance at all times. Wear oil-resistant rubber-soled footwear. Keep the floor clear of oil, scrap, and other debris. 16. MAINTAIN TOOLS PROPERLY. ALWAYS keep tools clean and in good working order. Follow instructions for lubricating and changing accessories. 17. CHECK FOR DAMAGED PARTS. Check for alignment of moving parts, jamming, breakage, improper mounting, or any other conditions that may affect the tool’s operation.
ELECTRICAL INFORMATION GROUNDING INSTRUCTIONS IN THE EVENT OF A MALFUNCTION OR BREAKDOWN, grounding provides the path of least resistance for an electric current and reduces the risk of electric shock. This tool is equipped with an electric cord that has an equipment grounding conductor and a grounding plug. The plug MUST be plugged into a matching outlet that is properly installed and grounded in accordance with ALL local codes and ordinances. DO NOT MODIFY THE PLUG PROVIDED.
KNOW YOUR DRYWALL SANDER Extension Locking Nut Variable Speed Adjustment Wheel Power Switch Hose Connection Port Locking Clasp Motor Hook & Loop Base Pad TROUBLESHOOTING PROBLEM Motor is not working. CAUSE 1) Wires in the main plug or in the socket are loose. 2) The switch is faulty. Unusual noises occur during operation. Motor is not working properly. Motor gets hot. 1) Switch contact has failed. 2) Components have jammed. 3) Too high of load has been applied.
ASSEMBLY WARNING: To avoid injury from accidental startups, turn switch OFF and remove the plug from the power source outlet before making any adjustments. 1. Unfold the front and back of the drywall sander. Push the clasp into the closed position to keep the drywall sander assembly from unfolding (Fig. A). 2. Attach the sanding disk of your choice to the face of the hook and loop base pad. Ensure the holes on the sanding disks align with the holes on the bottom of the pad (Fig. B). 3.
OPERATION VARIABLE SPEED CONTROL Use the speed wheel (Fig. D - 1) to adjust anywhere from 600 to 1500 RPM. This drywall sander is equipped with constant speed control to keep the pad running at a consistent rate despite changes in applied load. TURNING ON THE DRYWALL SANDER After setting the variable speed to your desired RPM, power the machine by pressing forward on the power switch (Fig. D - 2). 1 2 Fig. D MAINTENANCE Fig. E REPLACE THE SANDING PAD Insert the hex wrench into the hexagonal screw (Fig.
EXPLODED VIEW AND PARTS LIST No.
EXPLODED VIEW AND PARTS LIST
LIMITED TWO YEAR WARRANTY WEN Products is committed to build tools that are dependable for years. Our warranties are consistent with this commitment and our dedication to quality. LIMITED WARRANTY OF WEN CONSUMER POWER TOOLS PRODUCTS FOR HOME USE GREAT LAKES TECHNOLOGIES, LLC (“Seller”) warrants to the original purchaser only, that all WEN consumer power tools will be free from defects in material or workmanship for a period of two (2) years from date of purchase.
Thanks for remembering