OPERATOR’S MANUAL 9.
Table Of Contents SECTION PAGE Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Rules for Safe Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 General Instructions for All Power Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Rotary Tool Kit Specifications SPECIFICATIONS Model Number 2301 Charger Input 120V~60Hz Power Source 9.6 Volt Ni-Cd Batteries Speed 5,000-25,000 RPM Collet Capacity 3/32", 1/8" Charging Time 3 hours Package Contents: • 1–Cordless Rotary Tool • 1–Charger • 1–Adapter • 2–9.6 Volt Battery Packs • 1–Flexable Shaft • 1–LED worklight attachment • 1–Storage Case 100 pc.
Rules For Safe Operation The purpose of safety symbols is to attract your attention to possible dangers. The safety symbols, and the explanations with them, deserve your careful attention and understanding. The safety warnings do not by themselves eliminate any danger. The instructions or warnings they give are not substitutes for proper accident prevention measures. Symbol Meaning Safety Alert Symbol: Indicates danger, warning, or caution, may be used in conjunction with other symbols or pictographs.
General Instructions For All Power Tools READ ALL INSTRUCTIONS!!! • Know your power tool. Read the operator’s manual carefully. Learn the application and limitations as well as specific potential hazards related to this tool. • Keep guards in place and in working order. Never operate the tool with any guard or cover removed. Make sure all guards are operating properly before each use. • Remove adjusting keys & wrenches.
General Instructions For All Power Tools • Do not overreach. Keep proper footing and balance at all times. • Maintain tools with care. Keep tools sharp and clean for best and safest performance. Follow instructions for lubricating and changing accessories. • Disconnect all tools. When not in use, before servicing, or when changing attachments, blades, bits, cutters, etc, all tools should be disconnected from power source. • Reduce the risk of unintentional starting.
General Instructions For All Power Tools WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to cause cancer, birth defects or other reproductive harm.
General Instructions For All Power Tools WARNING: when servicing use only identical WEN® replacement parts. Use of any other parts may create a hazard or cause product damage. • Do not remove jammed cut-off pieces until tool rotation has stopped. • Never start the tool when the accessory is in contact with the work piece. • Never touch the rotating portion of the tool or other moving parts during use.
Specific Instructions For The Cordless Rotary Tool SAVE THESE INSTRUCTIONS! I. Safety Instructions for Battery Charger • Before using charger, read all instructions and cautionary markings on (1) charger, (2) battery pack, and (3) product using battery pack. • DANGER: 120 volts present at charging terminal. Do not probe with conductive objects. Danger of electrical shock or electrocution. • DANGER: If battery pack case is cracked or damaged, do not insert into charger.
Specific Instructions For The Cordless Rotary Tool II. Safety Instructions for Battery Packs The battery pack is not fully charged out of the carton. First read the safety instructions below. Then follow charging procedure. • Do not incinerate the battery pack even if it is severely damaged or no longer holds a charge. The battery pack can explode in a fire. • Under severe conditions, a small leakage of liquid from the battery pack is normal. This does not indicate a failure.
Specific Instructions For The Cordless Rotary Tool & Charging Procedure • The real secret of the Cordless Rotary Tool is its speed. To understand the advantages of its high speed, you have to know that the standard portable electric drill runs at speeds up to 2,800 revolutions per minute. The typical electric drill is a low-speed, high torque tool; the Cordless Rotary Tool is just the opposite— a high-speed, low torque tool.
Charging & Operating Procedure Caution • The battery pack must be charged before first use. • The battery pack reaches its full capacity only after several recharges. • Do not recharge battery pack after using the tool briefly, such as 15 minutes. Allow the battery pack to drain down somewhat before recharging. • During charging, the battery pack and charger may feel warm to the touch. This is normal. • Do not charge the battery pack in an air temperature below 40ºF or above 105ºF.
Operating Procedure WARNING: Always be sure the tool is in the Zero position before changing accessories, changing collets or servicing your cordless rotary tool. COLLET—To loosen, first press shaft lock button and rotate the shaft by hand until the lock engages the shaft preventing further rotation. CAUTION: Do not engage lock while the Rotary Tool is running. With the shaft lock engaged use the collet wrench to loosen the collet nut if necessary.
Operating Procedure point secured in the collet, turn on the Cordless Rotary Tool and run the 415 Dressing Stone lightly against the revolving wheel point. This removes high spots and turns up the wheel point to ensure good balance. Battery Pack Installation/Removal • To install battery, insert charged battery in the handle and secure with release button. • To remove battery, press the release buttons, located below the drill handle and gently pull the battery pack out. 1. Cordless Rotary Tool 2.
Using the Cordless Rotary Tool Operating Speeds for Accessories Set the speed indicator to fit the job to achieve the best job results when working with different materials. To select the right speed for each job, use a practice piece of material. Vary speed to find the best speed for the accessory you are using and the job to be done. Your Cordless Rotary Tool is equipped with a variable speed control dial.
Operating Instructions Flexible Extension Some work may require more precise control of the tool. For that purpose a slender flexible extension has been provided. To attach the flexible extension, remove the collar from the body of the tool. Pull the drive wire out of the flexible extension 2” to 3”. Remove the collet nut and collet from the rotary tool. Thread the end of the drive wire thru the collet nut and the collet. Insert the collet in the hole in the end of the tool shaft.
Maintenance Service WARNING: NO USER SERVICEABLE PARTS INSIDE. Preventive maintenance performed by unauthorized personnel may result in misplacing of internal wires and components, which could cause serious hazard. Disconnect tool and/or charger from power source before servicing. Cleaning WARNING: To avoid accidents, always disconnect the tool and/ or charger from the power supply before cleaning. The tool may be cleaned most effectively with compressed dry air.
WARRANTY WEN Products is committed to build tools that are dependable for years. Our warranties are consistent with this commitment and our dedication to quality LIMITED WARRANTY OF WEN CONSUMER POWER TOOLS PRODUCTS FOR HOME USE GREAT LAKES TECHNOLOGIES, LLC ("Seller") warrants to the original purchaser only, that all WEN consumer power tools will be free from defects in material or workmanship for a period of one year from date of purchase.
