User Documentation

ManualsBrandsWeidmueller ManualsBCF 3.81/180BCF 3.81/16/180ZE SN BK BX

We reserve the right to make technical changes.00/03.16

Assembly instructions

PUSH IN spring connection – plug-in connector BCF 3.81

OMNIMATE Signal – series BCF 3.81/180

All other technical data can be obtained from the data sheet

Cables suitable for connection:

Strip the insulation from the cables to a length of approx. 9mm ±1mm, even if you are using wire-end ferrules.

If you use wire-end ferrules with plastic collars, strip the cables to 11mm ±1mm.

min. cable connection cross-section max. cable connection cross-section

Solid (H05(07) V-U) 0.14 mm² 1.5 mm²

Flexible (H05(07) V-U) 0.14 mm² 1.5 mm²

with wire-end ferrule according to DIN 46 228/1 0.25 mm² 1.5 mm²

with wire-end ferrule; with collar DIN 46 228/4 0.25 mm² 1.0 mm²

*1; *2

with twin wire-end ferrule; with collar DIN 46 228/4 *3 2x 0.5 mm² (H0.5/14)

2x 0.75 mm² (H0.75/14)

*1;*2

AWG 26 18

*1: Restriction for max. wire cross-section: crimp shape according to European standard EN 60947-1. We recommend the following crimping tools:

– Crimping tool for wire-end ferrule of 0.25 mm² to 1.5 mm² with trapezoidal indentation crimp, type PZ6/5 (Order No. 9011460000)

– Crimping tool for wire-end ferrule of 0.14 mm² to 0.75 mm² with trapezoidal crimp, type PZ1.5 (Order No. 9005990000)

*2 Wire cross-section 1.50 mm² possible with the following restrictions: For a rated voltage of 125V/2.5KV at III/3 or 250/2.5KV at II/2.

*3 When connecting twin wire-end ferrules in neighbouring contact points, their orientation must be observed. Comparing gures:

Examples of crimp shape according to European standard EN 60947-1:

We recommend using the following wire-end ferrules:

Cable diameter Type Weidmüller colour code

Order number

DIN colour code

Order number

Stripping length

1.50 mm² H1.5/14 0463100000 9019120000 11 ±1 mm

1.00 mm² H1.0/14 0463000000 9019080000 11 ±1 mm

0.75 mm² H0.75/14 0462900000 9019040000 11 ±1 mm

0.50 mm² H0.5/14 0690700000 9019010000 11 ±1 mm

0.34 mm² H0.34/14 9025770000 11 ±1 mm

0.25 mm² H0.25/12 9025760000 9 ±1 mm

0.14 mm² H0.14/12 9028240000 9 ±1 mm

Summary of content (4 pages)

PAGE 1
Assembly instructions PUSH IN spring connection – plug-in connector BCF 3.81 OMNIMATE Signal – series BCF 3.81/180 All other technical data can be obtained from the data sheet Cables suitable for connection: Strip the insulation from the cables to a length of approx. 9 mm ± 1 mm, even if you are using wire-end ferrules. If you use wire-end ferrules with plastic collars, strip the cables to 11 mm ± 1 mm.
PAGE 2
PUSH IN connector design: slider / push-button / pusher Handling: Recommended tool: • Screwdriver blade 0.4 x 2.5 • Screwdriver blade standard DIN 5264 conductor entry end stop spring clamp Solid conductors: 1. A stripped solid conductor is simply plugged into the contact point up to the end stop. Conductors with wire-end ferrule: 1. Stranded conductors with crimped-on wire-end ferrules, with and without plastic collars, are simply plugged into the contact point up to the end stop.
PAGE 3
Montageanleitung PUSH IN Federanschluss – Steckverbinder BCF 3.81 OMNIMATE Signal – Serie BCF 3.81/180 Alle weiteren technischen Daten sind dem Datenblatt zu entnehmen. Anschließbare Leiter: Isolieren Sie die Leitungen auf einer Länge von ca. 9 mm ±1 mm ab, auch wenn Sie Aderendhülsen verwenden. Wenn Sie Aderendhülsen mit Kunststoffkragen verwenden, isolieren Sie die Leitungen auf 11 ±1 mm ab.
PAGE 4
Aufbau Push In Steckverbinder: Schieber / Push-Button / Pusher Handling: Leitereinführung Empfohlenes Werkzeug: • Schraubendreherklinge 0,4 x 2,5 • Schraubendreherklinge Norm DIN 5264 Anschlag Klemmfeder Starre Leiter: 1. Ein abisolierter starrer Leiter wird einfach, bis zum Anschlag, in die Klemmstelle gesteckt. Leiter mit Aderendhülse: 1. Mehrdrähtige Leiter mit aufgecrimpten Aderendhülsen, mit und ohne Kunststoffkragen, werden einfach, bis zum Anschlag, in die Klemmstelle gesteckt.