Use and Care Manual

ManualsBrandswedi ManualsFloor Installation Kits36 in. x 48 in. Shower Kit Primo

All products needed to build a wedi Fundo Primo point drain shower are included and provide a single manufacturer

warranty. Safe transportation in one box, easy estimating of product quantities needed. The shower floor units feature a

strong and pre-sloped surface which can be tiled over immediately whether you choose mosaic size or large format tile.

Pre-sloped extension panels are available so that virtually no limit exists for making any size or shape for custom shower

designs happen. Naturally, Fundo Primo is insulating keeping surfaces warmer. Especially when compared to traditional

mortar bed installations or other currently known methods for building showers such as those including use of sheet –

or liquid waterproofing membranes used in an attempt to manage water exposure – wedi Fundo Primo‘s simplicity and

high performance shows. The most unique advantage, however, is the complete and natural core waterproofness of

the wedi product and its completeness and range of components that will form an entire assembly system with Fundo

Primo engineered to fit and last. This is a true system with full warranty coverage.

Screws, Washers and Putty Knife

wedi Full Foam Curb Lean

wedi Building Panel

wedi Niche (optional)

wedi Shower Kit – Primo

Full Shower System in a Box

wedi Fundo Primo Shower Base

*Found in each kit:

 Fundo Primo Shower Base (1)

 wedi 36 in. or 48 in. x 60 in. x 1/2 in. Building Panels (4)

 wedi Full Foam Curb, Lean (1)

 wedi Fundo Kit Drain Standard (1)

 wedi Joint Sealant (7 10.5 oz. tubes)

 wedi Fastener Kit (1, screws/washers 100 ct.)

 wedi Corner Putty Knife (1)

 wedi Mixing Valve Flexi Collar (1)

 wedi Flexi Collar (1)

Summary of content (6 pages)

PAGE 1
wedi Shower Kit – Primo® Full Shower System in a Box 05 01 04 02 03 All products needed to build a wedi Fundo Primo point drain shower are included and provide a single manufacturer warranty. Safe transportation in one box, easy estimating of product quantities needed. The shower floor units feature a strong and pre-sloped surface which can be tiled over immediately whether you choose mosaic size or large format tile.
PAGE 2
wedi Fundo Primo Product Information These added values and its detail perfections eliminate the technical concerns in shower installations. However, this is not where wedi shower systems stop offering its added values. The wedi Fundo shower system adds to your productivity and enables you to provide real value to your customers.
PAGE 3
wedi Fundo Primo® Installation Before Installation: H ave 2 × 4 blocking installed over bottom plate between studs along to support wedi Building Panel to shower base transition area.  Subfloor is stable, even and load bearing, and meets deflection criteria of maximum L/360 as per IRC. Wooden or concrete structural substrates are dry and sufficiently load bearing considering live and dead load. Wood and Steel framing is sufficiently load bearing, plum and square.
PAGE 4
05 06 07 08 Turn the Fundo base upside Tighten the gaskets firmly Skim coat the thinset ANSI 118.4 and comb through with a 1/4” × 1/4” down and apply the rubber to the bases‘ steel ring using (6.4 × 6.4 mm) notched trowel. Channels pointing to the entrance. and the fiber gasket. the locking nut. Make sure Trowel the thinset on the rear side of the Fundo again using a 1/4” × 1/4” the drain body is still safely (6.4 × 6.4 mm) notched trowel.
PAGE 5
15 16 17 18 wedi Niches are installed in a cut out in the wedi wall and attached with A continuous 1/2” (12.7 mm) bead of sealant is set into the channel it‘s flange right into the center of 16” (406.4 mm) o.c. studs. wedi Joint and along the vertical curb notch part. A circle of 1/2” (12.7 mm) seal- Sealant is set along the connection of wall to niche.
PAGE 6
wedi Drain Cover Assembly / Insertion Insert cover frame into base hole (no glue / no screws). You may caulk between part and tile to create a flexible grout joint. Optional Extension Collar can be cut to height if part is needed. The caulk joint must not create a water barrier damming up the water draining through the thinset bed into the drain from below the tile. Therefore the thinset layer must be continuous toward the drain.