Burner User Manual

ManualsBrandsWeber ManualsBurner42376

TYPICAL 20 LP PROPANE GAS SUPPLY INSTALLATION

We strongly recommend that you use the Summit

Built-In

Tank Cabinet (#21280) for installations using a 20 lb LP cylinder, mounted

remotely in an “island” structure.

The Summit

Built-In Tank Cabinet is a CSA listed accessory for installing

a remote mounted 20 lb LP cylinder, in an “island” structure. Summit

Built-

In Tank Cabinet has a hose and regulator assembly and gas connections,

for connecting a remote mounted LP cylinder to the Summit

Built-In gas

grill. The hose and regulator is listed as a required part of the CSA listed

Summit

Built-In gas grill.

The Summit

Built-In Tank Cabinet also meets the requirements for venting,

tank retention and separation of the LP cylinder from a heat source as

outlined in the ANSI Standard for Outdoor Cooking Gas Appliances, Z21.58/

CSA 1.6 for LP enclosures.

The Summit

Built-In Tank Cabinet has its own installation guide.

If you do not use the Summit

Built-In Tank Cabinet, you need to hire

a licensed contractor or licensed plumber and they need to follow the

requirements described in the ANSI Standard for Outdoor Cooking Gas

Appliances, Z21.58/CSA 1.6 for LP enclosures.

The requirements described in the Standard for Outdoor Cooking Gas

Appliances, Z21.58/CSA 1.6. are as follows;

A remote enclosure for an LP gas cylinder shall be ventilated by openings at

both the upper and lower levels of the cylinder. This shall be accomplished

by one of the following:

a). One side of the remote LP cylinder enclosure shall be completely

open; or

b). If the remote LP cylinder enclosure is designed to have four sides,

a top and a bottom, ventilation is required for the remote LP cylinder

enclosure;

1). There should be at least two ventilation openings, (a hole or group

of holes, for the purpose of ventilation) in the sidewalls of the island

structure. The openings should be located within 5 inches (127mm) of

the top of the enclosure. The ventilation openings should be equally

sized and spaced at a minimum of 90 degrees, and be unobstructed.

The openings shall have a total free open area of not less than 20

square inches. (This relates to 1 square inch of ventilation area, per

pound of stored fuel capacity).

2). Ventilation openings (a hole or group of holes, for the purpose of

ventilation) should be provided at ﬂ oor level. The ventilation openings

should have a total free area of not less than 10 square inches. (This

relates to 1/2 square inch of ventilation area, per pound of stored

fuel capacity). There should be at least two ventilation openings

if the ventilation openings at ﬂ oor level are in the sidewall. The

ventilation openings should be within 5 inches (127mm) of the ﬂ oor.

The ventilation openings should be of equal size and be spaced at a

minimum of 90 degrees, and should be unobstructed.

3). The minimum size of the ventilation hole (s) should not be less than 1/4

inch.

4). The ventilation openings in the sidewalls should not allow venting into

the empty or “hollow” area of the “island”. If a gas leak should occur

or the LP cylinder should vent in the LP cylinder enclosure, the gas

should not be allowed to vent or migrate into the empty or “hollow” area

of the “island”. Ventilation openings in the sidewalls of the enclosure

should only communicate with the outside of the “island” structure, so

that the gas can dissipate outside of the “island” structure.

c). If the remote LP cylinder enclosure has four sides, a top and a bottom,

and is intended for installation in a built-in “island” enclosure;

1). At least one ventilation opening (a hole or group of holes, for the

purpose of ventilation) needs to be on one side of the enclosure

that communicates with the outside of the “island” structure. If a gas

leak should occur or the LP cylinder should vent in the LP cylinder

enclosure, the gas should not be allowed to vent or migrate into the

empty or “hollow” area of the “island”. Ventilation openings should only

communicate with the outside of the “island” structure, so that the gas

can dissipate outside of the “island” structure. The ventilation opening

should be located within 5 inches (127mm) of the top of the enclosure,

and should have a total free area of 20 square inches. (This relates to

1 square inch of ventilation area, per pound of stored fuel).

2). At least one ventilation opening (a hole or group of holes, for the

purpose of ventilation) needs to be on one side of the enclosure that

communicates with the outside of the “island” structure, at the bottom.

If a gas leak should occur or the LP cylinder should vent in the LP

cylinder enclosure, the gas should not be allowed to vent or migrate

into the empty or “hollow” area of the “island”. Ventilation openings

should only communicate with the outside of the “island” structure,

so that the gas can dissipate outside of the “island” structure. The

ventilation opening should be located within 5 inches (127mm) of the

bottom of the enclosure, and should have a total free area of 10 square

inches. (This relates to 1/4 square inch of ventilation area, per pound

of stored fuel).

GAS INSTRUCTIONS

TEST CONNECTIONS

All connections and joints must be thoroughly tested for leaks in accordance

with local codes and all listed procedures in the latest edition of the National

Fuel Gas Code ANSI Z223.1/NFPA 54.

 DANGER

Do not use an open ﬂ ame to check for gas leaks. Be

sure there are no sparks or open ﬂ ames in the area

while you check for gas leaks. This will result in a ﬁ re

or explosion which can cause serious bodily injury or

death, and damage to property.