2 Door / 1 Drawer Base Cabinet Date of Purchase ___ / ___ / ___ Lot Number: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. PLEASE READ AND KEEP FOR FUTURE REFERENCE. Do Not Return This Product! Contact our customer service team for help first. WARNING - Unit can tip over causing severe injury or death. - Anchor unit to stud in wall (if instructed to). - Do Not allow children to climb on unit. - Put heavy items on lower shelves or drawers.
Contact Us! Do NOT return this product! Contact our friendly customer service team first for help. Helpful Hints PEOPLE NEEDED FOR ASSEMBLY: 1-2 ESTIMATED ASSEMBLY TIME: 1 HOUR - Open your item in the area you plan to keep it to avoid excessive heavy lifting. - Identify, sort and count the parts before attempting assembly. - Compression dowels are lightly tapped in with a hammer. - Slides are labeled with a R (right) and L (left) for proper placement.
k Quic bly em Ass Tip Before You Start P P P P P Read through each step carefully and follow the proper order Separate and count all your parts and hardware Give yourself enough room for the assembly process Have the following tools: Flat Head Screwdriver, #2 Phillips Head Screwdriver and Hammer Caution: If using a power drill or power screwdriver for screwing, please be aware to slow down and stop when screw is tight. Failure to do so may result in stripping the screw.
Board Identification Not actual size F C A B Shelf 31117412030 Adjustable Shelf 32484412060 G D Left Panel 32484412010 Right Panel 32484412020 Bottom 31117412040 DWR SIDE I H Drawer Front 31117412080 Drawer Bottom 39991341052210D J Door (x2) 32484412070 Drawer Side (x2) 39991167346200C DWR BACK Drawer Back 39991167051390B This piece is paperboard construction. It is not made from wood, but is required for the assembly of your unit.
Board Identification Not actual size C B J A F G G DWR SIDE D DWR BACK I DWR SIDE 5 H
Part List 3 1 Actual Size 2 (x4) #A22610 cam bolt 4 (x4) #A22620 cam lock (x4) (x10) #A21660 #A11080 wood dowel 7/16" flat head screw (x10) #A12120 7/16" round head screw 9 8 7 6 5 (x2) #A11160 5/8" flat head screw (x8) #A12420 5/8" round head screw 13 12 11 10 14 (x4) (x2) (x4) #A12930 #A23030 #A89020 1-1/8" round confirmat screw bumper head screw (x6) (x4) (x34) (x4) #A80250 #A21110 #A17400 #A21970 8-32 x 7/8" nail drive fastener shelf support Not Actual Size 21a 16 15 (x3) #A52395
STEP 1 1 4 (x2) #A22610 (x3) #A11080 16 21a marked with "L" left cabinet member (x1) #A56770 (x4) #A65615 Loosen screw and separate hinge plate from hinge arm.
STEP 2 1 16 4 (x2) #A22610 (x3) #A11080 marked with "R" right cabinet member (x1) #A56770 (x4) #A65615 Loosen screw and separate hinge plate from hinge arm.
STEP 3 2 20a 3 Quick Assembly 20b (x4) #A22620 (x4) #A21660 Tip (x1) #A84050 Proper orientation of CAM LOCK Do not tighten screw.
STEP 4 8 10 7 6 (x2) #A11160 (x8) #A12420 (x4) #A12930 (x2) #A89020 19 (x4) #A44140 8 19 7 7 D bottom surface D top surface Unscrew the two halves of the foot. Attach bottom half to bottom (D) and screw top half back on.
STEP 5 UNLOCK All finished edges will face up.
STEP 6 9 (x4) #A23030 All finished edges will face up.
STEP 7 11 (x34) #A21110 IMPORTANT! THE BACK PANEL IS A STRUCTURAL PART OF THIS UNIT AND MUST BE INSTALLED PROPERLY. Attached the back panel as shown nailing straight into the raw edges. Assure that the unit is square. Distance from corner to corner must be equal as shown. 11 J "raw surface shown" Assure that your unit is square. Distance from corner to corner must be equal as shown. Flush the bottom edge of the back panel with the bottom edge of the bottom (D).
STEP 8 12 15 (x4) #A17400 (x4) #A65615 (x2) #A52395 16 16 12 G x2 12 15 14
STEP 9 5 18 (x4) #A12120 (x2) #A54520 DWR SIDE 18 18 5 5 5 DWR SIDE 5 side view side view 15
STEP 10 5 (x4) #A12120 Be sure the groove in the drawer sides are centered with the groove in the drawer front.
STEP 11 I finished surface DWR SIDE H 17 DWR SIDE
STEP 12 13 (x4) #A21970 You will need to tap the drive fasteners (13) lightly with a hammer to securely fasten.
STEP 13 12 21c 15 4 left drawer member 21d (x4) #A11080 right drawer member (x1) #A56770 (x1) #A52395 (x2) #A17400 4 Note: Attach slides (21c&21d) first then attach handle.
STEP 14 5 17 (x1) #A54900 (x2) #A12120 Turn drawer over. Using two screws (5), attach the drawer brace (17) as shown.
STEP 15 For Masonry, Concrete, or other wall materials: Consult your local hardware store for appropriate anchors to securely attach the safety bracket. 20c 20d IMPORTANT: THIS UNIT MUST BE SECURE TO THE WALL TO HELP PREVENT TIPOVER. FOLLOW THESE INSTRUCTIONS TO INSTALL THE ANTI-TIPPING SAFETY BRACKET PROVIDED WITH THIS PRODUCT. WARNING Serious or fatal crushing injuries can occur from furniture tipover.
STEP 16 Attach the two doors as shown by sliding the hinge arm onto the hinge plate. Tighten this screw.
STEP 17 Install the drawer as shown below. Follow adjustment details below to adjust drawer and doors. A C Door Adjustment: Up & Down - Loosen screw "A", adjust and retighten. Side to Side - Loosen screw "C" and tighten "B"will adjust door to middle of unit. Loosen "B" and tighten "C" will adjust door to outside of unit. B&C A B A Note: The drawer bracket holes are slotted. Drawer fronts can be adjusted by loosening screws, making needed adjustments and retightening screws.
STEP 18 14 Using the shelf supports (14), place the adjustable shelf (F) behind the door area.
Maximum Loads This unit has been designed to support the maximum loads shown. Exceeding these load limits could cause sagging, instability, product collapse, and/or serious injury. 25 lbs 11.3 kg 50 lbs 22.6 kg 50 lbs 22.6 kg Warning: Risk of injury to persons - do not place a television on this furniture. This furniture is not approved for use with a television.
Register your product to receive the following: * New trend details - sneak peek on what's new * Surveys - have a voice within our community * Exclusive deals and discount codes * Quick and easy replacement part service To register your product, Please visit us. Visit your local retailer's website, rate your purchased product and leave us some feedback! We would like to extend a big "Thank You" to all of our customers for taking the time to assemble this product, and to give us your valuable feedback.
Español Cubierta Delantera Este libro de instrucciones contiene información IMPORTANTE de seguridad. Por favor lea y manténgalo para referencia en el futuro. No Regrese este producto! Comuniquese con nuestro amistoso equipo de servicio al cliente para obtener ayuda. PRECAUCION Este mueble puede volcarse y causar graves heridas y/o muerte. Anclar el mueble a un poste de madera en la pared (si esto se requiere). No Permita que los niños monten el mueble.
Español Página 7 / 8 Afloje el tornillo y separe la pala de bisagra del brazo articulado. Página 9 No apriete el tornillo. Página 10 Desenrosque las dos mitades del pie. Pegue la mitad inferior a la parte de abajo (D) y atornille de nuevo a parte superior. Página 13 ¡IMPORTANTE! EL PANEL TRASERO ES UNA PARTE ESTRUCTURAL DE ESTA UNIDAD Y SE DEBE INSTALAR DE MANERA APROPIADA. Pegue el panel trasero como se muestra, clavándole directo en los bordes desnudos. Asegúrese de que la unidad esté nivelada.
Español Página 21 ADVERTENCIA El volcamiento del mobiliario podría causar lesiones graves o fatales, por aplastamiento.
Español Página 25 CARGA MAXIMA Esta unidad ha sido diseñada para soportar la carga máxima anotada. El exceder estos límites puede causar inestabilidad, colapsarse y/o causar serias lesiones. ADVERTENCIA: Riesgo de lesiones a las personas - no coloque un televisor sobre muebles. Este mueble no está aprobado para su uso con un televisor.
Français Couverture Avant CE LIVRET D'INSTRUCTION CONTIENT DES INFORMATIONS IMPORTANTES SUR LA SÉCURITÉ. VEUILLEZ LIRE ET GARDER POUR UNE RÉFÉRENCE FUTURE Ne retournez pas ce produit! Contactez notre équipe de service à la clientèle amicale d'abord pour obtenir de l'aide. ATTENTION Le meuble peut basculer et causer des blessures graves ou la mort. Ancrer le meuble à une planche murale dans le mur (si indiqué). Ne laissez pas les enfants grimper sur le meuble.
Français Page 7/8 Desserrez la vis et séparez la plaque de charnière du bras de charnière. Page 9 Ne serrez pas la vis. Page 10 Dévissez les deux moitiés du pied. Fixez la moitié inférieure au bas (D) et vissez la moitié supérieure à nouveau. Page 13 IMPORTANT! LE PANNEAU ARRIÈRE FAIT PARTIE STRUCTURELLE DE CETTE UNITÉ ET DOIT ÊTRE INSTALLÉ CORRECTEMENT. Fixez le panneau arrière comme illustré en clouant directement dans les bords bruts. Assurez-vous que l'unité soit carrée.
Français Page 21 ATTENTION Des blessures graves ou mortelles par écrasement peuvent survenir suite au renversement d'un meuble.
Français Page 25 CHARGES MAXIMALES Ce meuble a été conçu pour supporter les charges maximales indiquées. En excédant ces limites de charge, le meuble pourrait devenir instable, s'effondrer, et/ou causer des blessures graves. AVERTISSEMENT : Risque de blessure corporelle - ne pas placer une télévision sur ce meuble. Ce meuble n'est pas approuvé pour une utilisation avec une télévision.
