User's Manual

ManualsBrandsWatt Stopper ManualsElectronicsMRP6W/MRP7W

How to install and use the

wireless Miro

plug-in lamp

module (MRP6)

English

Read and retain these instructions

Français

Español

Ready?

Load Types

For more information on designing,

installing and using wireless Miro

systems, and for expert technical

help, call 1-800-223-4185, or visit our

web site at:

www.passandseymour.com/miro

Use the wireless Miro

plug-in lamp

module to control most types of floor and

table lamps of the following load types (25-

300W at 120V):

 Incandescent & quartz halogen lamps

 Magnetic low voltage transformers (max

load 250W)

 Electronic low voltage transformers rated

for dimming (max load 250W)

 Cold cathode, neon ballasts, rated for

dimming (max load 250W)

Do not mix different load types on the

same dimmer

Do not use for motors or for fluorescent

lighting fixtures

Do not use for light fixtures with integral

dimmers

Installation

Plug the wireless Miro

plug-in lamp module

into a convenient 15amp 120V grounded

receptacle.

Plug the light fixture into the grounded

15amp outlet on the base of the lamp

module.

Check that the light fixture is switched on by

pressing the × button on the lamp

module. If the light does not come on,

flip its switch to the on position, and

leave it there. If it still doesn’t come on,

check the lamp.

Get Set…

Configuration

Figure 2

To prevent interference between neighboring

systems, wireless Miro

devices must

acquire a unique house ID before use. It’s

simple!

1. With all devices installed and energized,

check that every wireless Miro

device

is showing a yellow LED. If not, check

that the circuit breaker is on and that the

device is correctly installed.

2. All devices in a home must be ‘bound’ to

the same home ID. For a new wireless

Miro

installation, simultaneously press

and hold the raise and lower buttons or

paddle (Ú) of any device for 2 seconds.

Its LED flashes yellow, indicating that it

has acquired a unique House ID.

3. Check that all other wireless Miro

device LEDs are flashing green,

indicating that they have acquired the

same House ID.

4. Return to the first device, and press Ú

again for 2 seconds. All device LEDs

revert to green, indicating that house

binding is complete.

Note: if you’re adding the device to an

existing wireless Miro

installation, simply

press and hold Ú on any previously bound

device for 2 seconds to start the procedure,

verify that the newly added device LED is

flashing green, indicating that it has acquired

the House ID. Press and hold Ú for 2

seconds again on the same previously

installed device to terminate.

Figure 1

Status LED

2, 4

Note: when you

see Ú in the

instructions, press

the up (×) and

down (Ø) arrow

buttons at the same

time

Grounded

15amp outlet

Summary of content (5 pages)

PAGE 1
How to install and use the wireless MiroTM plug-in lamp module (MRP6) English Read and retain these instructions Ready? Load Types For more information on designing, installing and using wireless MiroTM systems, and for expert technical help, call 1-800-223-4185, or visit our web site at: Use the wireless MiroTM plug-in lamp module to control most types of floor and table lamps of the following load types (25300W at 120V): Incandescent & quartz halogen lamps Magnetic low voltage transformers (max
PAGE 2
Go! Use! 1, 2 3, 4 IMPORTANT – Air Gap Isolation: to isolate the load for relamping, unplug the light fixture from the lamp module outlet. Figure 3 Advanced Operation 1, 3 wireless MiroTM remote switch mounted at a conventional light switch location 2 MiroTM wireless plug-in lamp module Now, the lamp module is controlled from the wall switch location, just like a permanently installed dimmer. Figure 4 1. Press × momentarily to fade the circuit to its last-used level – press twice for full bright 2.
PAGE 3
Cleaning Clean only using a cloth dampened with water and a little mild detergent. Use of solvents or hydrocarbon-based cleaners may cause permanent damage. Troubleshooting Problem: At house binding, not all the wireless MiroTM devices in the house are flashing green. In larger homes, some of the devices may be out of range of the initiating device. In this case, it will be necessary to add a wireless MiroTM Radio Repeater to boost radio signal range.
PAGE 4
• Consult the dealer or an experienced radio/TV technician for help. Caution: Any changes or modifications to this device not explicitly approved by Pass & Seymour/Legrand could void your authority to operate this equipment.
PAGE 5
Lifetime Warranty MiroTM is much more than lighting control! For information on MiroTM wiring devices, decorative wall plates, home networks and home automation solutions, visit our web site at www.passandseymour.com/miro The device you have purchased is warranted under normal use against defects in workmanship and materials for as long as you own the device.