Use and Care Manual
TECHNICAL DATA
WAT-01
WW
WATCO
®
LACQUER CLEAR WOOD FINISH
Form: GDH-416
Rev.: 080714
1
.DESCRIPTION AND USES .
Watco
®
Lacquer Clear Wood Finish is a durable lacquer finish
designed for spray or brush application on wood. It fills in the
pores of most woods, eliminating the need for wood filler. It is
ideal for furniture, doors, cabinets and paneling. It is not
recommended for floors or exterior surfaces.
.PRODUCTS .
SKU SIZE DESCRIPTION
63081 Spray Clear Gloss
63041 Quart Clear Gloss
63031 Gallon Clear Gloss
63181 Spray Semi-Gloss Clear
63141 Quart Semi-Gloss Clear
63131 Gallon Semi-Gloss Clear
63281 Spray Satin Clear
63241 Quart Satin Clear
6331 Gallon Satin Clear
PRODUCT APPLICATION .
SURFACE PREPARATION
ALL SURFACES – All surfaces must be clean, dry, and free of
wax, grease, oil, shellac, mildew, and polishes. Remove wax
with a wax stripper, shellac with a paint stripper, and mildew with
a solution of 10% household bleach and water.
PREVIOUSLY FINISHED SURFACES – For best adhesion,
surfaces must be clean, dry, and free of old finishes, dust, dirt,
oils, or foreign matter. Old finishes in poor condition must be
removed. Sand to obtain a smooth surface. Remove all sanding
dust using a vacuum or cloth dampened with mineral spirits.
STAINED OR PAINTED WOOD - Follow manufacturer’s
direction for application of stain or paint. Make certain surface is
thoroughly dry before applying Watco Clear Lacquer.
UNFINISHED WOOD - Sand using 150-220 grit sandpaper and
remove all sanding dust with a vacuum or a rag dampened with
mineral spirits. If a filler or putty is used, make sure it does not
contain wax and allow for enough time to dry thoroughly.
WARNING! If you scrape, sand or remove old paint, you may
release lead dust. LEAD IS TOXIC. EXPOSURE TO LEAD
DUST CAN CAUSE SERIOUS ILLNESS SUCH AS BRAIN
DAMAGE, ESPECIALLY IN CHILDREN. PREGNANT WOMEN
SHOULD ALSO AVOID EXPOSURE. Wear a NIOSH-approved
respirator to control lead exposure. Clean up carefully with a
HEPA vacuum and a wet mop. Before you start, find out how to
protect yourself and your family by contacting the National Lead
Information Hotline at 1-800-424-LEAD or log on to
www.epa.gov/lead.
PRODUCT APPLICATION (cont.) .
APPLICATION
Use adequate ventilation at all times. Do not apply in direct
sunlight. Apply only when the air and surface temperatures are
between 55-90°F (13-32°C) and the relative humidity is below
85%. If applying over white or pastel paints or stains, test in an
inconspicuous area before beginning. Testing is important when
applying over paints or stains as an undesired appearance may
occur when these products are topcoated with a lacquer finish.
BRUSH - Stir thoroughly before and during use. To prevent
bubbles in the finish, DO NOT SHAKE, over brush, or apply with
a roller. Apply using a good quality bristle brush or applicator.
Allow the finish to dry 2 hours and then recoat. Recoat only when
the previous coat has dried clear and feels hard. If any coat has
dried more than 6 hours, lightly sand with 220 grit sandpaper
before recoating to avoid brush marks. Apply additional coats
following directions above. A minimum of 3 coats is
recommended. Allow finish to dry 24 hours before light use.
Allow 7 days before subjecting the surface to normal usage.
SPRAYS - Shake can vigorously for 2 minutes before use. Spray
light coats 8 to 12 inches from the surface to avoid runs and sags.
Allow the finish to dry 2 hours and then recoat. Recoat only when
the previous coat has dried clear and feels hard. Several light
coats result with a better finish than one heavy coat. If any coat
has dried more than 6 hours, lightly sand with 220 grit sandpaper
before recoating. Apply additional coats following directions
above. A minimum of 3 coats is recommended. Allow finish to
dry 24 hours before light use. Allow 7 days before subjecting the
surface to normal usage.
CLEAN UP
Sprays – Clean spray tip immediately after use by turning the
can upside down and spraying for several seconds.
Brush- Clean tools and equipment with lacquer thinner.