Yard & Pool Vinyl Gate REALLY Important stuff to know about installing your WamBam gate. 1-877-778-5733 www.wambamfence.
Yard & Pool Vinyl Gate Reality Check 1 - Read Over Fence Instructions First Your gate and fence will work better together as an integrated solution if you first take the time to read and understand your fence instructions. 2 - Do a Dry Run First on the Gate Frame Only (not pickets or boards) Please do not glue or screw your gate frame together until you have first temporarily assembled the gate. In other words, do a dry run first.
Yard & Pool Vinyl Gate 4 - Ideally, Do Not Hang Your Gate System Off a Single Non-Supported Post. Your gate will perform better and last longer if your hinge post is connected to a panel of fence which is connected to another post. The weight strain will be transferred unto two posts versus just one. Installing fence panels on both sides of your gate is the ideal in all situations. If this is not possible because of space restrictions, please contact us for alternative solutions to overcome.
Yard & Pool Vinyl Gate Box Contents .050in. wall thickness .090in. wall thickness Each Gate Box Includes: • Top Rail (1) • Gate Hinges (2) • Pickets (8) • Arch Brackets (2) • Gate Latch (1) • Vertical Stiles (2) • Tube of Glue (1) • Gate Brace (1) • Stainless Steel Screws (16) • Gate Bottom Brackets (2) • Bottom Rail (1) Sold Separately: • 6ft. Posts (2-Pack) Posts Sold Separately as 2-Packs For more information, contact us at 1 877-778-5733.
Yard & Pool Vinyl Gate PRODUCT OVERVIEW Gate Assembly 3.56in. Gate Installation 1.5in. A 58.84in. 52in. D C 56.84in. 41.5in. 22in. 3.5in. 7.75in. B 3.5in. 1.5in. 3.5in. 20in. 50in. 36in. 54.5in. C B 1.5in. Ground Concrete Footing 48in. A 2in. 3.5in. 1.5in. Posts Sold Separately D 1.5in. 10in. 3.5in. .090in. wall thickness For more information, contact us at 1 877-778-5733.
Yard & Pool Vinyl Gate Detailed Installation Instructions STEP 1 Assemble the Gate Frame Bottom & Sides A Handle with care: vinyl weld glue takes approximately five minutes to cure. UE GL Completely assembled gate shown B A - Run bead of vinyl weld continously around the inside of the gate bracket Did you do a dry run of assembly first? Please read page 1 of instructions. Note that the bottom rail is Ribbed internally. Insert fully to this point.
Yard & Pool Vinyl Gate STEP 2 Insert Pickets & Assemble the Gate Frame Top A D UE GL Did you do a dry run of assembly first? Please read page 1 of instructions. A - Run bead of vinyl weld continously around the inside of the gate bracket B Insert pickets in the proper order according to their height as shown above. Insert to this point.
Yard & Pool Vinyl Gate STEP 3 Screw Gate Frame/Brackets A 48in. A - ENSURE YOUR GATE IS SQUARE and screw brackets as illustrated. The corner-to-corner measurement must be the same, and the width of the gate should be 48”. For more information, contact us at 1 877-778-5733.
Yard & Pool Vinyl Gate STEP 4 Fasten Gate Hinges & Gate Latch A For swimming and other child safety gates, most safety standards specify: a) Your fence height needs to be between 4’ and 6’ high minimum b) Your gate needs to open outwards away from the pool c) Latch releasing mechanism to be minimum 54” off the ground. *The Plain Jane gate will require a specialized latching system to meet pool code. Use MagnaLatch Top Pull Hardware (not included) and Captain Morgan Post Caps Only.
Yard & Pool Vinyl Gate STEP 5 Assemble & Fasten Gate Brace B A Gate Brace Parts (2) .25” x .75” Hex Bolts (2) .25” Lock Washers (2) .25” Nuts (4) 1.25” (#10) Screws 1 Top Bar Bottom Bar 2 3 A - Assemble gate bace with bolts, washers and nuts as necessary. B - Re-confirm the gate is square, and screw bracing into place. For more information, contact us at 1 877-778-5733.
Yard & Pool Vinyl Gate Position, Adjust & Align Gate/ STEP 6 Secure Hinges to Posts A A - Use temporary spacers or blocks to rest the gate on during alignment and installation B B - Fasten hinges to posts with screws For more information, contact us at 1 877-778-5733.
Yard & Pool Vinyl Gate STEP 7 Level Gate & Adjust Hinges A B LEVEL A - Fasten gate hinges accordingly C Adjust the spring tension in gates as necessary. Use steel insert pin. C - Hinges can be adjusted moderately to bring gate into level alignment with post B - Check for level, fit and function to latching post D Latch is designed for left and right hand applications. Temporarily remove the spring, bolt and reverse paddle portion as necessary.
Yard & Pool Vinyl Gate STEP 8 Align & Install Latch A A - Align and fasten the gate latch catch to fit and function with the gate finger. B Congratulations! You did it! Go grab a beverage of your choice, admire your handy work, and show us what you got by entering our annual photo/video contests! For more information, contact us at 1 877-778-5733.