Instructions
Table Of Contents
- 1 Notes about this Documentation
- 2 Important Notes
- 3 Overview
- 4 Properties
- 4.1 Hardware Description
- 4.1.1 View
- 4.1.2 Labeling and type plate
- 4.1.3 Connectors
- 4.1.4 Display Elements
- 4.1.5 Operating Elements
- 4.1.6 Memory Card Slot
- 4.2 Schematic Diagram
- 4.3 Technical Data
- 4.3.1 Mechanical Data
- 4.3.2 System Data
- 4.3.3 Power Supply
- 4.3.4 Clock
- 4.3.5 Programming
- 4.3.6 ETHERNET
- 4.3.7 Communication Interface
- 4.3.8 Connection Type
- 4.3.9 Digital inputs
- 4.3.10 Digital outputs
- 4.3.11 Analog inputs
- 4.3.12 Analog outputs
- 4.3.13 Climatic Environmental Conditions
- 4.3.14 Analog Temperature Sensors
- 4.3.15 Fieldbus
- 4.3.16 Other
- 4.4 Approvals
- 4.1 Hardware Description
- 5 Function Description
- 6 Mounting
- 7 Connecting
- 8 Commissioning
- 9 e!RUNTIME Runtime Environment
- 10 Diagnostics
- 11 Service
- 12 Removal
- 13 Disposal
- 14 Accessories
- 15 Appendix
- 15.1 Configuration Dialogs
- 15.1.1 Web-Based-Management (WBM)
- 15.1.1.1 “Information” Tab
- 15.1.1.2 “Configuration” Tab
- 15.1.1.2.1 “PLC Runtime Configuration” Page
- 15.1.1.2.2 “TCP/IP Configuration” Page
- 15.1.1.2.3 “Ethernet Configuration” Page
- 15.1.1.2.4 “Configuration of Host and Domain Name” Page
- 15.1.1.2.5 “Routing” Page
- 15.1.1.2.6 “Clock Settings” Page
- 15.1.1.2.7 “Create Bootable Image” Page
- 15.1.1.2.8 “Firmware Backup” Page
- 15.1.1.2.9 “Firmware Restore” Page
- 15.1.1.2.10 “Active System” Page
- 15.1.1.2.11 “Mass Storage” Page
- 15.1.1.2.12 “Software Uploads” Page
- 15.1.1.2.13 “Configuration of Network Services” Page
- 15.1.1.2.14 “Configuration of NTP Client” Page
- 15.1.1.2.15 “PLC Runtime Services” Page
- 15.1.1.2.16 “SSH Server Settings” Page
- 15.1.1.2.17 “DHCP Server Configuration” Page
- 15.1.1.2.18 “Configuration of DNS Server” Page
- 15.1.1.2.19 “Status overview” Page
- 15.1.1.2.20 “Configuration of Connection
” Page - 15.1.1.2.21 “Configuration of General SNMP Parameters” Page
- 15.1.1.2.22 “Configuration of SNMP v1/v2c Parameters” Page
- 15.1.1.2.23 “Configuration of SNMP v3 Users” Page
- 15.1.1.2.24 “WBM User Configuration” Page
- 15.1.1.3 “Fieldbus” Tab
- 15.1.1.4 “Security” Tab
- 15.1.1.4.1 “OpenVPN / IPsec Configuration” Page
- 15.1.1.4.2 “General Firewall Configuration” Page
- 15.1.1.4.3 “Interface Configuration” Page
- 15.1.1.4.4 “Configuration of MAC Address Filter” Page
- 15.1.1.4.5 “Configuration of User Filter” Page
- 15.1.1.4.6 “Certificates” Page
- 15.1.1.4.7 “Security Settings” Page
- 15.1.1.4.8 “Advanced Intrusion Detection Environment (AIDE)” Page
- 15.1.1.5 “Diagnostic” Tab
- 15.1.1 Web-Based-Management (WBM)
- 15.1 Configuration Dialogs
- List of Figures
- List of Tables
150 Appendix WAGO I/O System Compact
751-9301 Compact Controller 100
Manual
Version 1.1.0, valid from FW Version 03.08.07(20)
15.1.1.2.7 “Create Bootable Image” Page
You can create a bootable image on the “Create Bootable Image” page.
“Create bootable image from boot device” Group
Once the destination has been determined and output, it is then checked and the
results of this check are displayed below the settings:
Table 80: WBM “Create Bootable Image” Page – “Create bootable image from active partition” Group
Parameters
Meaning
Boot Device
The medium from which the boot was made is
displayed.
Destination
Depending on which medium has been booted, the
following destination is available for selection after
boot-up for the image to be generated:
System was booted
from
Target partition for
“bootable image”
Memory Card
Internal Flash
Internal memory
Memory Card
- Free space on target device:
If the available memory space is less than 5% a warning is displayed. You
can still start the copy process despite the warning. If the available space is
too low, a corresponding message is displayed and copying cannot be
started.
- Device being used by CODESYS:
If the device is being used by CODESYS, a warning is displayed. Although
it is not recommended, you can still start the copying procedure despite this
warning.
Click [Start Copy] to start the copying procedure. If the outcome of the test is
positive, copying begins immediately. If errors have been detected, a
corresponding message is displayed and copying is not started. If warnings have
been issued, these are displayed again and you must then confirm that you still
wish to continue.