Owner’s Manual Read this manual for complete instructions Español (página 13) Opti-Stain Sprayer Contents Questions? 2 4 5 6 7 8 10 11 24 26 Call Wagner Technical Service at: Important Safety Information Components Material Preparation Assembly Spraying Cleanup Maintenance Troubleshooting Parts List Warranty 0614 • Form No. 0529841D 1-800-328-8251 Register your product online at: www.wagnerspraytech.
Important Safety Information Read all safety information before operating the equipment. Save these instructions. Indicates a hazardous situation which, if not avoided, could result in death or serious injury. To reduce the risks of fire or explosion, electrical shock and the injury to persons, read and understand all instructions included in this manual. Be familiar with the controls and proper usage of the equipment. Grounding Instructions This product must be grounded.
Important Safety Information WARNING - To reduce the risk of injury: 1. Always wear appropriate gloves, eye protection, clothing and a respirator or mask when painting. Hazardous vapors – Paints, solvents, insecticides, and other materials can be harmful if inhaled or come in contact with body. Vapors can cause severe nausea, fainting or poisoning. 2. Do not operate or spray near children. Keep children away from equipment at all times. 3. Do not overreach or stand on an unstable support.
Components j l m k a b c i d e f c g h Item Description 4 Item Description a Turbine h Suction tube b Filter housing i Viscosity cup c Filter (2) j Nut d Material flow control k Air cap e 2-stage trigger l Nozzle f Release tab g 600 ml cup English m Nozzle seal © Wagner Spray Tech - All Rights Reserved
Material Preparation Note: Before spraying, the material being used may need to be thinned with the proper solvent as specified by the material manufacturer. Never exceed the thinning advice given by the coating manufacturer. Do not use materials with a flashpoint below 100°F (38°C). Follow the instructions below. 1 To Prepare the Material: 1. Stir the spraying material thoroughly. 2. Dip the viscosity test cup completely into the spraying material. 3.
Assembly Before you begin: 1 NEVER point the spray gun at any part of the body. To Assemble: IMPORTANT: Make sure the power cord is unplugged. 1. Insert the suction tube into the intake opening. 2. Align the suction tube a. If you are going to be spraying in a downward direction, the angled end of the suction tube should be pointing toward the front of the gun. b. If you are going to be spraying in an upward direction, the angled end of the suction tube should be pointing toward the rear of the gun.
Spraying Adjust Spray Pattern The spray pattern shape is adjusted by turning the ears of the air cap to either the vertical, horizontal, or diagonal positions. The positions of the air cap and the corresponding spray pattern shapes are illustrated below. Test each pattern and use whichever pattern is suitable for your application. never trigger the gun while adjusting the ears on the air cap. NEVER point the spray gun at any part of the body.
Cleanup Flushing the unit Before you begin: When cleaning, use the appropriate cleaning solution (warm, soapy water for latex materials; mineral spirits for oil-based materials) important: Never clean air cap or air holes in the nozzle with sharp metal objects. Do not use solvents or lubricants containing silicone. 1 Special cleanup instructions for use with flammable solvents (must have a flashpoint above 100ºF (38ºC): • • • • 1/2 Always flush spray gun outside. Area must be free of flammable vapors.
Cleanup Cleaning the Nozzle 1 To Clean the Nozzle: 1. Make sure power cord is unplugged. Push the tab below the trigger, twist and separate the nozzle from the turbine. Wipe the exterior of the cup and nozzle until clean. 2. Unscrew the nut and remove the air cap and nozzle. 3. Remove the parts as shown*. Clean all parts with a cleaning brush and the appropriate cleaning solution. Reassemble when clean**. 4. Clean the air vent (c) on the suction tube with a soft bristled cleaning brush. 5.
Maintenance Cleaning the Filters: important: You should inspect the air filters in the turbine to see if it is excessively dirty. If it is dirty, follow these steps to replace it. important: Never operate your unit without the air filters. Dirt could be sucked in and interfere with the function of the unit. 1. Unplug the spray gun. Remove the filter cover from the turbine by removing the two screws holding it in place. 2. Remove the dirty filters and replace with new ones.
Troubleshooting PROBLEM CAUSE SOLUTION Problem A: Little or no material flow 1. 2. 3. 4. 1. 2. 3. 4. Nozzle clogged. Suction tube clogged. Material flow setting too low. Suction tube loose. 5. Air vent on suction tube blocked. 6. No pressure build up in container. 7. Air valve tube disconnected, valve seal missing. 8. Air valve tube or valve seal plugged. 9. Air filter clogged. 10. Spray material too thick. 11. Nozzle seal missing or worn. Clean. Clean. Increase material flow setting.
Parts List •Title Lista de piezas Nozzle assembly • Conjunto del boquilla Replacement parts available by calling customer service 1 Los repuestos están disponibles llamanado al servicio a clientes. 1-800-328-8251 4 2 3 5 9 7 8 6 10 # Part No. Pieza No. English Description Español Descripción Qty. Cant.
Parts List • Lista de piezas Turbine • Turbina Replacement parts available by calling customer service Los repuestos están disponibles llamanado al servicio a clientes. 1-800-328-8251 # Part No. Pieza No. 1 --------- 2 0417323 1 2 English Description Español Descripción Turbine (includes item 2) Turbina (incluye le articulo 2) 1 Filter Filtro 2 © Wagner Spray Tech - All Rights Reserved Español Qty. Cant.
Garantía limitada Equipo de atomización de pintura HVLP Este producto, fabricado por la Wagner Spray Tech Corporation (Wagner), está garantizado contra defectos de materiales y de mano de obra por un año a partir de la fecha de compra siempre y cuando se utilice de acuerdo con las recomendaciones e intrucciones impresas de Wagner. Esta garantía no cubre daños ocasionados por el uso incorrecto, accidentes, negligencia por parte del usario o el desgaste normal.
Limited Warranty HVLP paint spray equipment This product, manufactured by Wagner Spray Tech Corporation (Wagner), is warranted against defects in material and work-manship for one year following date of purchase if operated in accordance with Wagner’s printed recommendations and instructions. This warranty does not cover damage resulting from improper use, accidents, user’s negligence or normal wear.
