Operator’s Manual Vibratory Rammer BS 50-2, BS 50-2i BS 60-2, BS 60-2i BS 70-2, BS 70-2i BS 65-V EN 5200016051 5 2 0 0 0 01 1 6 0114 0 5 1
Copyright notice © Copyright 2013 by Wacker Neuson Production Americas LLC All rights, including copying and distribution rights, are reserved. This publication may be photocopied by the original purchaser of the machine. Any other type of reproduction is prohibited without express written permission from Wacker Neuson Production Americas LLC. Any type of reproduction or distribution not authorized by Wacker Neuson Production Americas LLC represents an infringement of valid copyrights.
Rammer Foreword Foreword SAVE THESE INSTRUCTIONS—This manual contains important instructions for the machine models below. These instructions have been written expressly by Wacker Neuson Production Americas LLC and must be followed during installation, operation, and maintenance of the machines.
Foreword Rammer Machine ■ From this point forward in this documentation, Wacker Neuson Production documentation Americas LLC will be referred to as Wacker Neuson. ■ Keep a copy of the Operator’s Manual with the machine at all times. ■ Use the separate Parts Book supplied with the machine to order replacement parts. ■ If you are missing either of these documents, contact Wacker Neuson to order a replacement or visit www.wackerneuson.com.
Rammer Foreword Manufacturer’s approval This manual contains references to approved parts, attachments, and modifications. The following definitions apply: ■ Approved parts or attachments are those either manufactured or provided by Wacker Neuson. ■ Approved modifications are those performed by an authorized Wacker Neuson service center according to written instructions published by Wacker Neuson. ■ Unapproved parts, attachments, and modifications are those that do not meet the approved criteria.
Foreword Rammer Notes 6 wc_tx003550gb_FM10.
EC Declaration of Conformity Manufacturer Wacker Neuson Production Americas LLC, N92W15000 Anthony Avenue, Menomonee Falls, Wisconsin 53051 USA Product Product BS 50-2i Product category Vibratory Rammer Product function To compact soil Item number 5200000657, 5200000658, 5200000659, 5200000660, 5200000661, 5200011099 Net installed power 1.
EC Declaration of Conformity Manufacturer Wacker Neuson Production Americas LLC, N92W15000 Anthony Avenue, Menomonee Falls, Wisconsin 53051 USA Product Product BS 50-2 Product category Vibratory Rammer Product function To compact soil Item number 5200000652, 5200000653, 5200000654, 5200000655, 5200000656 Net installed power 1.
EC Declaration of Conformity Manufacturer Wacker Neuson Production Americas LLC, N92W15000 Anthony Avenue, Menomonee Falls, Wisconsin 53051 USA Product Product BS 60-2i Product category Vibratory Rammer Product function To compact soil Item number 5200000664, 5200000665 Net installed power 1.
EC Declaration of Conformity Manufacturer Wacker Neuson Production Americas LLC, N92W15000 Anthony Avenue, Menomonee Falls, Wisconsin 53051 USA Product Product BS 60-2 Product category Vibratory Rammer Product function To compact soil Item number 5200000663, 5200000666 Net installed power 1.
EC Declaration of Conformity Manufacturer Wacker Neuson Production Americas LLC, N92W15000 Anthony Avenue, Menomonee Falls, Wisconsin 53051 USA Product Product BS 70-2i Product category Vibratory Rammer Product function To compact soil Item number 5200000672, 5200000673 Net installed power 2.
EC Declaration of Conformity Manufacturer Wacker Neuson Production Americas LLC, N92W15000 Anthony Avenue, Menomonee Falls, Wisconsin 53051 USA Product Product BS 70-2 Product category Vibratory Rammer Product function To compact soil Item number 5200000670, 5200000671, 5200000676 Net installed power 2.
EC Declaration of Conformity Manufacturer Wacker Neuson Production Americas LLC, N92W15000 Anthony Avenue, Menomonee Falls, Wisconsin 53051 USA Product Product BS 65-V Product category Vibratory Rammer Product function To compact soil Item number 5200000669 Net installed power 2.
Rammer 1 Foreword 3 EC Declaration of Conformity 7 Safety Information 1.1 1.2 1.3 1.4 1.5 1.6 2 30 Label Locations .................................................................................. 30 Label Meanings .................................................................................. 31 35 Lifting the Rammer ............................................................................. 35 Transporting the Rammer ..................................................................
Table of Contents 5.4 5.5 5.6 5.7 5.8 5.9 5.10 5.11 5.12 5.13 5.14 Rammer Checking and Changing the Ramming System Oil .............................57 Checking the Fuel Lines and Fittings ..................................................59 Maintaining the Shoe Hardware ..........................................................60 Inspecting the Machine .......................................................................61 Cleaning the Engine Cooling Fins ................................................
Rammer 1 1.1 Safety Information Safety Information Signal Words Used in this Manual This manual contains DANGER, WARNING, CAUTION, NOTICE, and NOTE signal words which must be followed to reduce the possibility of personal injury, damage to the equipment, or improper service. This is the safety alert symbol. It is used to alert you to potential personal hazards. ► Obey all safety messages that follow this symbol.
Safety Information 1.2 Rammer Machine Description and Intended Use This machine is a vibratory rammer. The Wacker Neuson Rammer consists of a gasoline or diesel engine, a clutch, a fuel tank, a spring-loaded ramming system, a ramming shoe, and a handle. The engine transmits power through the ramming system and ramming shoe, generating percussive impact force to compact soil. The operator guides and controls the machine from behind using the handle.
Rammer 1.3 Safety Information Safety Guidelines for Operating the Machine Operator training Before operating the machine: ■ Read and understand the operating instructions contained in all manuals delivered with the machine. ■ Familiarize yourself with the location and proper use of all controls and safety devices. ■ Contact Wacker Neuson for additional training if necessary. When operating this machine: ■ Do not allow improperly trained people to operate the machine.
Safety Information Safe operating practices Rammer When operating this rammer: ■ Remain aware of the rammer’s moving parts. Keep hands, feet, and loose clothing away from the rammer’s moving parts. ■ When working near the edges of pits, slopes, trenches, and platforms, always operate the rammer in such a way that there is no possibility of it tipping over or falling in. When operating this rammer: ■ Do not operate a rammer in need of repair.
Rammer 1.5 Safety Information Service Safety Service training Before servicing or maintaining the machine: ■ Read and understand the instructions contained in all manuals delivered with the machine. ■ Familiarize yourself with the location and proper use of all controls and safety devices. ■ Only trained personnel shall troubleshoot or repair problems occurring with the machine. ■ Contact Wacker Neuson for additional training if necessary.
Safety Information Rammer Replacing parts and labels ■ Replace worn or damaged components. ■ Replace all missing and hard-to-read labels. ■ When replacing electrical components, use components that are identical in rating and performance to the original components. ■ When replacement parts are required for this machine, use only Wacker Neuson replacement parts or those parts equivalent to the original in all types of specifications, such as physical dimensions, type, strength, and material.
Rammer 1.6 Safety Information Operator Safety while Using Internal Combustion Engines WARNING Internal combustion engines present special hazards during operation and fueling. Failure to follow the warnings and safety standards could result in severe injury or death. ► Read and follow the warning instructions in the engine owner’s manual and the safety guidelines below. DANGER Exhaust gas from the engine contains carbon monoxide, a deadly poison. Exposure to carbon monoxide can kill you in minutes.
Labels 2 Rammer Labels 2.1 Label Locations BS 50-2i/BS 60-2i/BS 70-2i BS 50-2/BS 60-2/BS 70-2, BS 65-V L L H H C C M D M D E E B K R J B K A F G A G N wc_gr010404 BS 65-V Q P O wc_gr011507 30 wc_si000837gb_FM10.
Rammer 2.2 Labels Label Meanings DANGER Asphyxiation hazard. ■ Engines emit carbon monoxide. ■ Do not run the machine indoors or in an enclosed area unless adequate ventilation, through such items as exhaust fans or hoses, is provided. ■ No sparks, flames, or burning objects near the machine. ■ Stop the engine before refueling. wc_sy5200000316 WARNING ■ To reduce the risk of hearing loss, always wear hear- ing protection when operating this machine. ■ Read the Operator’s Manual.
Labels Rammer Emission control information This engine meets U.S. EPA exhaust regulations for 2014. This equipment meets U.S. EPA evaporative standards using certified components Engine family: EWIXS.080RMR Emission compliance period: 300 hours (heavy use) This Engine Meets U.S. EPA EXH REGS for 2014 This Equipment Meets U.S. EPA / EVP Standards Using Certified Components EF: EWIXS.
Rammer Labels Turtle = Idle/slow engine speed Rabbit = Full/fast engine speed G 1. Move the throttle to the IDLE position. 1 2. Close the choke. 2 181641 H Engine oil tank ■ Use only Wacker Neuson two-cycle or other fully syn- thetic oil meeting the NMMA TC-W3, JASO FD, or ISO-L-EGD specification. Read the Operator’s Manual. WARNING K Operation of This Equipment May Create Sparks That Can Start Fires Around Dry Vegetation. A Spark Arrestor May be Required.
Labels Rammer Adjusting tool label Refer to Selecting Ramming Stroke and Adjusting Ramming Stroke for explanation of this label. Read the Operator’s Manual O Locking lever label 1 2 2 Refer to Selecting Ramming Stroke and Adjusting Ramming Stroke for explanation of this label. P CAUTION Cutting hazard. Moving parts under the housing cover can cut skin and catch clothing. Do not operate the machine while the housing cover is open.
Rammer 3 3.1 Lifting and Transporting Lifting and Transporting Lifting the Rammer Requirements ■ Lifting device (crane or hoist) capable of supporting the rammer’s weight (see the identification plate on the rammer) ■ Lifting gear (hooks, slings, and/or chains) capable of supporting the rammer’s weight ■ Engine stopped and cool to the touch Procedure Perform the procedure below to lift the rammer. 1. Attach the lifting gear to the central lifting cable (a). a e wc_gr010405 WARNING Crushing hazard.
Lifting and Transporting 3.2 Rammer Transporting the Rammer Overview This rammer can be transported in a vehicle, or manually, depending on job site conditions and distance to be traveled. NOTICE: Do not tow this rammer. Requirements ■ Engine stopped and cool to the touch ■ Lifting devices and gear ■ Fuel tank drained (if transporting horizontally) Transporting in a vehicle Perform the procedure below to transport the rammer in a vehicle. WARNING Lifting injury.
Rammer Lifting and Transporting Continued from the previous page. If the rammer cannot be secured in the upright position, a. Drain the fuel tank to prevent fuel from leaking from the cap (c). b. Lay the rammer down only as shown and tie it to the vehicle at points (a) and (b). c b a d wc_gr010406 Transporting manually Rollers (d) enable the rammer to be rolled from one location to another. Perform the procedure below to transport the rammer manually. 1.
Operation 4 4.1 Rammer Operation Preparing the Machine for First Use 1. Make sure all loose packaging materials have been removed from the machine. 2. Check the machine and its components for damage. If there is visible damage, do not operate the machine! Contact your Wacker Neuson dealer immediately for assistance. 3. Take inventory of all items included with the machine and verify that all loose components and fasteners are accounted for. 4. Attach component parts not already attached. 5.
Rammer 4.2 Operation Recommended Fuel For rammers with oil injection (BS 50-2i, BS 60-2i, BS 70-2i) If the rammer has a fuel tank (a) and an oil tank (b), it has oil injection—No premixing of the gasoline and oil is required. Mixing of the gasoline and oil is done automatically by the machine. b a wc gr010452 Fill the fuel tank with regular unleaded gasoline. Fill the oil tank with Wacker Neuson two-cycle oil (or an equivalent). See chapter Technical Data for fuel and oil specifications.
Operation Rammer For rammers without oil injection (BS 50-2, BS 60-2, BS 70-2, BS 65-V, BS 65-V) If the rammer has a fuel tank (c) but no oil tank, the engine requires a two-cycle gasoline/oil mixture. c wc_gr011466 NOTICE: Use only the recommended gasoline/oil mixture to fuel this machine. Using gasoline alone will severely damage the engine. Requirements ■ Use only Wacker Neuson two-cycle or other fully synthetic oil meeting the NMMA TC-W3, JASO FD, or ISO-L-EGD specification.
Rammer 4.3 Operation Refueling the Machine Requirements ■ ■ ■ ■ Machine shut down Engine cool Machine standing upright on the ramming shoe Fresh, clean fuel supply Procedure Perform the procedure below to refuel the machine. WARNING Fire and burn hazard. Fuel and its vapors are extremely flammable. ► Keep all sources of ignition away from the machine while refueling. ► Do not refuel if the machine is positioned in a truck fitted with a plastic bed liner.
Operation 4.4 Rammer Filling the Oil Tank For rammers with oil injection (BS 50-2i, BS 60-2i, BS 70-2i) If the rammer has a fuel tank (a) and an oil tank (b), it has oil injection. The oil tank requires oil. b c a Requirements ■ ■ ■ ■ Machine shut down Engine cool Machine standing upright on the ramming shoe Wacker Neuson 2-cycle or equivalent oil Procedure Perform the procedure below to fill the oil tank. d wc_gr011417 1. Remove the oil tank cap (c).
Rammer 4.5 Operation Purging the Oil Lines For rammers with oil injection (BS 50-2i, BS 60-2i, BS 70-2i) b If the rammer has a fuel tank (a) and an oil tank (b), it has oil injection. The oil lines may need purging. a wc_gr010452 When As needed: when air bubbles are visible in the oil supply line or discharge line Requirements ■ ■ ■ ■ ■ ■ ■ Purging the oil supply line Perform the procedure below to purge the oil supply line.
Operation Rammer Continued from the previous page. Purging the oil discharge line Perform the procedure below to purge the oil discharge line. 1. Locate the oil discharge line (c). e c d e c e c g f wc_gr010578 2. If air bubbles are visible in the oil discharge line, they must be manually purged using one of two possible methods: Method 1: Disconnect the oil discharge line at the oil pump (d).
Rammer 4.6 Operation Position of the Operator For optimal control, performance, and minimal hand/arm vibration, follow the guidelines below when using the machine. Grasp the handle with both hands as shown. wc_gr011468 Stand behind the rammer, walking slowly and guiding the direction of travel as the machine moves forward. Note: Hand/Arm Vibration (HAV) has been optimized for the hand position shown. Reported HAV levels are measured at position A in conformance with EN 1033 and ISO 5349 standards. 4.
Operation 4.8 Rammer Starting, Operating, and Stopping the Machine Requirements ■ Rammer is in serviceable condition and has been properly maintained ■ There is fuel in the tank Starting the machine Perform the procedure below to start the machine. 1. Move the throttle to the idle position (c2). This will automatically start the flow of fuel. c2 c3 c1 a b wc_gr011422 2. Close the choke (a). 3. Pump the purge bulb (b) 6 to 10 times or until you see fuel in the bulb.
Rammer Operation Continued from the previous page. Operating the machine Perform the procedure below to operate the rammer. 1. Move the throttle to the full position (c3). The choke will open automatically. 2. Guide the rammer’s direction of travel. Allow the rammer to pull itself forward. Do not try to overpower the rammer. CAUTION Do not lift or move the rammer to another location while it is operating. You may lose control of it.
Operation 4.9 Rammer Emergency Shutdown Procedure Procedure If a breakdown or accident occurs while the machine is operating, follow the procedure below: 1. Reduce engine speed to idle. 2. Stop the engine. 3. Close the fuel valve. 4. Contact the rental yard or machine owner for further instructions. 48 wc_tx003552gb_FM10.
Rammer 4.10 Operation Selecting and Adjusting the Ramming Stroke (BS 65-V) Overview The length of the ramming stroke directly affects the impact force delivered by the rammer. Selecting the appropriate stroke depends on job requirements and soil conditions. The ramming stroke is adjusted by rotating a locking lever inside the housing. WARNING Personal injury hazards. ► Observe the safety requirements described below when adjusting the ramming stroke.
Operation Rammer Continued from the previous page. Adjusting the ramming stroke Perform the procedure below to adjust the ramming stroke. 1. Remove the adjusting tool (b) from the housing cover. Open the housing cover. b 3 1 c 2 d wc_gr008956 2. Verify that the arrow (d) at the center of the locking lever is pointing up. WARNING Crushing hazard. If the arrow is pointing down, the spring system is not balanced. The top half of the rammer could drop unexpectedly while making the stroke adjustment.
Rammer Operation Continued from the previous page. Note: Choosing a stroke setting applies tension to the spring system. This tension will release as the locking lever is returned back to its locked position. When this happens, the rammer will settle, causing the handle and crankcase to drop down. The movement is slight but happens quickly. Be aware of this when moving the locking lever. 5. Push or pull the adjusting tool to move the locking lever back to its locked position (Operation 3).
Operation 4.11 Rammer Optional Equipment The following optional equipment is available: ■ Foot extensions (a)—a narrow rammer foot for use in compacting trenches and in areas of limited clearance. Available sizes are 102 mm x 102 mm (4 in. x 4 in.) and 102 mm x 309 mm (4 in. x 12 in.). ■ Wheel kit (b)—solid rubber tires joined to a steel axle, attached to the lifting handle by means of a slip-on retaining plate. a b wc_gr008992 Contact your Wacker Neuson dealer for ordering information.
Rammer 5 Maintenance Maintenance WARNING A poorly maintained machine can malfunction, causing injuries or permanent damage to the machine. ► Keep the machine in safe operating condition by performing periodic maintenance and making repairs as needed. 5.
Maintenance 5.2 Rammer Periodic Maintenance Schedule The table below lists basic machine maintenance. Tasks designated with check marks may be performed by the operator. Tasks designated with square bullet points require special training and equipment. After first 5 hours Every week or 25 hours Tighten ramming shoe hardware. Inspect the machine. Daily before starting Check air filter. Replace air filter as needed. Check ramming system oil level in sightglass.
Rammer 5.3 Maintenance Servicing the Air Cleaner When Inspect the air filter daily. Replace filter elements as needed. Requirements ■ ■ ■ ■ ■ Engine stopped and cool to the touch Replacement filter elements (as needed) Mild detergent Warm water Compressed air NOTICE: Do not run the engine without the main paper air filter (b). Severe engine damage will occur. WARNING Explosion and fire hazards. ► Never use gasoline or other types of low flash point solvents for cleaning the air filter.
Maintenance Rammer Continued from the previous page. 2. Remove the main paper filter element (b), foam prefilter (c), and foam discharge filter (d) and inspect them for holes or tears. Replace the element and filters if they are damaged. 3. Replace the main paper filter element (b) if it appears heavily soiled. 4. Clean the foam prefilter and foam discharge filter (c, d) with low-pressure compressed air. If the filters are extremely soiled, wash them in a solution of mild detergent and warm water.
Rammer 5.4 Maintenance Checking and Changing the Ramming System Oil Background Lubricating oil is distributed throughout the ramming system by the vibrating action of the rammer. Holes drilled in the piston carry oil from the bottom of the rammer to the crankcase as the rammer operates. Oil in the ramming system must be maintained at the correct level to ensure that the ramming system operates efficiently. Checking the oil level Perform the following procedure to check the ramming system oil level.
Maintenance Rammer Continued from the previous page. 2. Remove the sightglass. Clean the threads of the sightglass, then wrap the threads with Teflon tape. 3. Add oil to the machine through the sightglass opening in the housing. 4. Re-install the sightglass, but do not torque it at this time. 5. Stand the machine upright and check the oil level. 6. Add oil as needed so that it fills 1/2 to 3/4 of the sightglass. 7. Torque the sightglass to 9 Nm (6 ft.lbs.).
Rammer 5.5 Maintenance Checking the Fuel Lines and Fittings When Daily before starting the machine Procedure 1. Check the fuel lines (a) and fittings (b) for cracks and leaks. a b a wc_gr010410 2. Repair or replace components as needed. Result The fuel lines and fittings have now been checked. wc_tx003553gb_FM10.
Maintenance 5.6 Rammer Maintaining the Shoe Hardware When On new machines, or after replacing shoe, check and tighten shoe hardware after the first five hours of operation. Inspect hardware every week thereafter. Procedure Torque hardware as specified. Cast Iron Shoe Plastic Shoe T1 T5 T5 T3 T1 T3 wc_gr005385 Torque Nm ft.lbs. T1 86 63 T3 19 14 T5 79 58 60 wc_tx003553gb_FM10.
Rammer 5.7 Maintenance Inspecting the Machine When After the first five hours, and every week or every 25 hours thereafter (whichever comes first) Requirements ■ Engine stopped ■ Machine cool to the touch ■ Replacement parts as needed (refer to the Parts Book) Procedure 1. Perform a walk-around inspection of the machine. Check for: Loose or missing fasteners Cracked, corroded, or missing parts Damaged controls CAUTION Injury hazard.
Maintenance 5.8 Rammer Cleaning the Engine Cooling Fins When Every week, or every 25 hours (whichever comes first) Background Clean engine cooling fins allow fresh air to freely circulate around the combustion chamber. Adequate air circulation is necessary to prevent the engine from overheating. Requirements ■ Engine stopped and cool to the touch ■ Compressed air Procedure Perform the procedure below to clean the engine cooling fins. 1. Locate the engine cooling fins (a). a wc_gr011470 2.
Rammer 5.9 Maintenance Cleaning and Checking the Spark Plug When Every week, or every 25 hours (whichever comes first) Requirements ■ ■ ■ ■ ■ Engine stopped and cool to the touch Spark plug wrench Spark plug gap tool Wire brush Replacement spark plug as needed (see Technical Data) WARNING Burn hazard. The engine and muffler become very hot during operation and require cool-down time after the engine is stopped. ► Do not touch the engine, muffler, or spark plug until the machine is cool.
Maintenance 5.10 Rammer Inspecting and Cleaning the Fuel Filter When Every year or every 1200 hours (whichever comes first) Requirements ■ ■ ■ ■ Procedure Perform the procedure below to clean the fuel filter. Engine stopped Fuel tank empty Clean, dry, lint-free cloth Replacement fuel filter (as needed) 1. Clamp, then disconnect the fuel hose (b) from the fuel filter (a). BS xx-2 BS xx-4 a c b 10 mm (3/8 in.) a a wc_gr010412 2. Unscrew and remove the fuel filter. 3.
Rammer 5.11 Maintenance Replacing the In-Line Fuel Filter Assembly When Every 5 months or every 500 hours (whichever comes first) Requirements ■ Engine stopped ■ Replacement in-line fuel filter assembly Procedure Perform the procedure below to replace the in-line fuel filter assembly. The in-line fuel filter assembly consists of the fuel filter (a) and two hoses (b). a b BS 50-2i, BS 60-2i, BS 70-2i BS 50-2, BS 60-2, BS 70-2 b b a a wc_gr010413 1. Set the throttle to the OFF position.
Maintenance 5.12 Rammer Adjusting the Idle Speed Requirements ■ Tachometer ■ Phillips screwdriver Procedure Perform the procedure below to adjust the idle speed. 1. Remove the guard (c). 2. Start the engine and allow it to warm up to operating temperature. 3. Using the tachometer, set the engine idle speed with engine running at idle and choke (a) fully open. 4. Adjust idle speed screw (b) in or out to obtain correct idle speed. Refer to Technical Data for correct idle and operating rpm.
Rammer 5.13 Maintenance Long-Term Storage Introduction This machine requires preventive maintenance before long-term storage. Performing preventive maintenance helps to preserve machine components and ensures that the machine will be ready for future use. When Prepare your machine for extended storage if it will not be operated for 30 days or more. Preparing for storage Perform the procedures below to prepare your machine for storage. 1. Complete any needed repairs. 2.
Maintenance 5.14 Rammer Machine Disposal / Decommissioning Introduction This machine must be properly decommissioned at the end of its service life. Responsible disposal of recyclable components, such as plastic and metal, ensures that these materials can be reused—conserving landfill space and valuable natural resources. Responsible disposal also prevents toxic chemicals and materials from harming the environment.
Rammer 6 Basic Troubleshooting Basic Troubleshooting Problem Cause Remedy Engine does not start, or stalls. No fuel in tank Add fuel. Spark plug fouled Clean or replace spark plug. Engine does not accelerate, is hard to start, or runs erratically. Spark plug fouled Clean or replace spark plug. Obstructed muffler and/or exhaust port Clear obstructions. Dirty or clogged air cleaner Service air cleaner. Engine overheats. Dirty cooling fins Clean the cooling fins.
Technical Data 7 7.1 Rammer Technical Data BS 50-2i Machine BS 50-2i Engine model — Engine speed - operating rpm 4400 ± 100 Engine speed - idle rpm 2000 ± 100 Maximum rated power @ rated speed1 kW (hp) 1.7 (2.2) @ 4400 rpm Clutch engagement rpm 2500 ± 100 Spark plug type Champion QL87YC Electrode gap mm (in.) 0.76 (0.030) Cylinder head compression (cold) bar/cm2 (psi) 8.0–9.
Rammer 7.3 Technical Data BS 60-2i Machine BS 60-2i Engine model — Engine speed - operating rpm 4400 ± 100 Engine speed - idle rpm 2000 ± 100 Max. rated power @ rated speed1 kW (hp) 1.8 (2.4) @ 4400 rpm Clutch engagement rpm 2500 ± 100 Spark plug type Champion QL87YC Electrode gap mm (in.) 0.76 (0.030) Cylinder head compression (cold) bar/cm2 (psi) 8.0–9.
Technical Data 7.5 Rammer BS 70-2i Machine BS 70-2i Engine model — Engine speed - operating rpm 4400 ± 100 Engine speed - idle rpm 2000 ± 100 Max. rated power @ rated speed1 kW (hp) 2.0 (2.7) @ 4400 rpm Clutch engagement rpm 2500 ± 100 Spark plug type Champion QL87YC Electrode gap mm (in.) 0.76 (0.030) Cylinder head compression (cold) bar/cm2 (psi) 8.0–9.
Rammer 7.7 Technical Data BS 50-2 Machine BS 50-2 Engine model — WM80 Engine speed - operating rpm 4400 Engine speed - idle rpm 2000 ± 100 Max. rated power @ rated speed1 kW (hp) 1.7 (2.2) @ 4400 rpm Clutch engagement rpm 2500 ± 100 Spark plug type Champion QL87YC Electrode gap mm (in.) 0.76 (0.030) Cylinder head compression (cold) bar/cm2 (psi) 8.0–9.
Technical Data 7.9 Rammer BS 60-2 Machine BS 60-2 Engine model — WM80 Engine speed - operating rpm 4400 Engine speed - idle rpm 2000 ± 100 Max. rated power @ rated speed1 kW (hp) 1.8 (2.4) @ 4400 rpm Clutch engagement rpm 2500 ± 100 Spark plug type Champion QL95YC Electrode gap mm (in.) 0.76 (0.030) Cylinder head compression (cold) bar/cm2 (psi) 8.0–9.
Rammer 7.11 Technical Data BS 70-2 Machine BS 70-2 Engine model — WM80 Engine speed - operating rpm 4400 Engine speed - idle rpm 2000 ± 100 Max. rated power @ rated speed1 kW (hp) 2.0 (2.7) @ 4400 rpm Clutch engagement rpm 2500 ± 100 Spark plug type Champion QL87YC Electrode gap mm (in.) 0,76 Cylinder head compression (cold) bar/cm2 (psi) 8.0–9.
Technical Data 7.13 Rammer BS 65-V Machine BS 65-V Engine model — WM80 Engine speed - operating rpm 4400 ± 100 Engine speed - idle rpm 1800 ± 100 Max. rated power @ rated speed1 kW/hp 2.0 (2.7) @ 4400 rpm Clutch engagement rpm 2500 ± 100 Spark plug type Champion QL95YC Electrode gap mm (in.) 0.76 (0.030) Cylinder head compression (cold) bar/cm3 (psi) 8.0–9.
Rammer 7.15 Technical Data Sound Measurements Products are tested for sound pressure level in accordance with EN ISO 11204. Sound power level is tested in accordance with European Directive 2000/14/EC Noise Emission in the Environment by Equipment for Use Outdoors. ■ the sound pressure level at operator's location (LpA) db(A). ■ the guaranteed sound power level (LWA) db(A). 7.
Technical Data 7.17 Rammer Dimensions—BS 50-2i, BS 50-2 mm (in.) 673 (26.5) 343 (13.5) 940 (37.0) A B wc_gr011405 A mm (in.) B mm (in.) 5200000656 5200000686 280 (11.03) 337 (13.27) 5200000643 5200000658 5200000659 5200000641 5200000654 6200000685 250 (9.84) 337 (13.25) 5200000661 5200000687 5200000655 280 (11.03) 344 (13.55) 5200000657 5200000652 165 (6.50) 337 (13.25) 5200011099 5200000653 190 (7.50) 344 (13.
Rammer 7.18 Technical Data Dimensions—BS 60-2i, BS 60-2, BS 70-2i, BS 70-2, BS 65-V mm (in.) 673 (26.5) 343 (13.5) 965 (38.0) A B wc_gr011411 wc_td000585gb_FM10.fm A mm (in.) B mm (in.) 5200000663 5200000666 5200000688 280 (11.02) 336 (13.25) 5200000646 5200000665 5200000690 — 280 (11.02) 342 (13.45) BS 70-2i BS 70-2 A mm (in.) B mm (in.) 5200000649 5200000673 5200000671 330 (12.99) 342 (13.45) 5200000650 5200000672 5200000670 5200000676 280 (11.02) 336 (13.
Emission Control Systems Information and Warranty 8 Emission Control Systems Information and Warranty The Emission Control Warranty and associated information is valid only for the U.S.A., its territories, and Canada. 8.1 Emission Control System Background Information Introduction Wacker Neuson spark-ignited engines/equipment must conform with applicable Environmental Protection Agency (EPA) emissions regulations.
Emission Control Systems Information and Warranty Tampering and Altering Tampering with or altering the emission control system may increase emissions beyond the legal limit. If evidence of tampering is found, Wacker Neuson may deny a warranty claim. Among those acts that constitute tampering are: ■ Removing or altering of any part of the air intake, fuel, or exhaust systems. ■ Altering or defeating the speed-adjusting mechanism causing the engine to operate outside its design parameters. 8.
Emission Control Systems Information and Warranty For the components listed in the following table, an authorized Wacker Neuson dealer/service center will, at no cost to you, make the necessary diagnosis, repair, or replacement necessary to ensure that the engine/equipment complies with the applicable EPA regulations. All defective parts replaced under this warranty become property of Wacker Neuson.
Emission Control Systems Information and Warranty Evaporative Emissions Systems Covered Components Evaporative control system Fuel tank (if applicable) Fuel tank cap (if applicable) Fuel line (if applicable) Fuel line fittings (if applicable) Clamps (if applicable) Carbon canister (if applicable) Purge port connector (if applicable) Miscellaneous parts associated with the evaporative emission control system Clamps Gaskets Mounting brackets What is not covered ■ Failures other than those resulting from
Emission Control Systems Information and Warranty Owner’s Warranty Responsibility The engine/equipment owner is responsible for the performance of the required maintenance listed in the Wacker Neuson engine/equipment operator’s manual. Wacker Neuson recommends that all receipts covering maintenance on the engine/equipment be retained, but Wacker Neuson cannot deny warranty coverage solely for the lack of receipts or for the failure to ensure the performance of all scheduled maintenance.
Wacker Neuson SE · Preußenstraße 41 · D-80809 München · Tel.: +49-(0)89-3 54 02-0 · Fax: +49 - (0)89-3 54 02-390 Wacker Neuson Corporation · N92W15000 Anthony Ave. · Menomonee Falls, WI 53051 · Tel. : (262) 255-0500 · Fax: (262) 255-0550 ·Tel. : (800) 770-0957 Wacker Neuson Limited - Room 1701–03 & 1717–20, 17/F. Tower 1, Grand Century Place, 193 Prince Edward Road West, Mongkok, Kowloon, Hongkong.
