Installation guide IS7121/IS7121-2/IS7121-22 DECT 6.0 cordless telephone with wireless doorbell Before using this product, read this Installation guide for instructions for installing the telephone base, handset and doorbell. For basic settings and operation instructions, see the provided Abridged user’s manual.
1 Install telephone base & charger Click! Plug! DSL filter Click! Plug! Plug!
Battery Pack BT164392/BT264392 2.4V 550mAh Ni-MH WARNING : DO NOT BURN OR PUNCTURE BATTERIES Made in China CR1222 THIS SIDE UP / CE CÔTÉ VERS LE HAUT 1 3 Battery Pack / Bloc-piles : (2.4V Ni-MH) WARNING / AVERTISSEMENT : DO NOT BURN OR PUNCTURE BATTERIES. NE PAS INCINÉRER OU PERCER LES PILES. Made in China / Fabriqué en chine CR1232 THIS SIDE UP / CE CÔTÉ VERS LE HAUT Battery Pack / Bloc-piles : (2.4V Ni-MH) WARNING / AVERTISSEMENT : DO NOT BURN OR PUNCTURE BATTERIES.
3 Install wall mount bracket (optional) 1 Unplug! Unplug! 2 Plug! Click! 3 4 Slide the bracket down!
4 Install doorbell battery • The doorbell can be supported by AC power only. See pages 10 and 12 on how to install the power adapter. BASIC INSTALLATION COMPLETED! Keep reading for doorbell location testing. 5 Doorbell location testing Before mounting the doorbell on a wall, make sure you test if the location you install the doorbell is in range, and adjust the camera angle to best suit your needs.
When you check for the desirable location to install the doorbell: • Make sure the visitor is standing in a reasonable distance away from the doorbell. 50 degrees Shooting area 18 inches 63 inches • • • 20 inches Avoid mounting it to where it is exposed to direct sunlight. Avoid mounting it to where reflections may be caused by sunlight, for example, opposite to a white wall. Avoid placing other cordless devices near the doorbell. They may cause interference.
To adjust the shooting area, you may either relocate the doorbell in different height level, or adjust the camera angle (see below). To adjust the camera angle: Angle Angle Adjustment Adjustment Angle Adjustment View Right View Left View Rotate to Right Left View Rotate Left to Right CAUTION • Tilt the lever to adjust the angle of the camera lens. The camera lens can be adjusted to left, right or down, up to 10 degrees.
6 Doorbell wall mount installation Make sure you have done Step 5 above before you mount the doorbell on the wall. 1. Use the two holes on the doorbell wall mount cover to mark the desirable installation location on the wall. 2. If you drill the holes into a stud, go to Step 3. -ORIf you drill the holes into the wall, insert the wall anchors into the holes.
3. Align the wall mount cover and screws with the holes in the wall (or stud). Align 4. Use a sharp object to open a hole on the soft plastic part on the doorbell wall mount cover, then route the power adapter cord through the hole. Open a hole and route the cord through the hole.
5. Loosen the screws and the metallic plates, then slide the metal part of the wires underneath the metallic plates as shown. Twist the screws to secure. Metallic plate Screws Metallic plate Wire with red end Wire with black end If you already have a wired doorbell installed, see Installing the doorbell with an existing wired doorbell from pages 14 to 16 to install your new IS7121 doorbell unit.
6. Push the doorbell gently onto the wall mount until they are sealed tightly. This doorbell meets the IPX4 waterproof standard. Make sure the doorbell is tightly sealed with its wall mount cover in order to maintain its waterproof ability. Seal tightly Push Push 7. Tighten the screw into the threaded socket at the bottom to secure.
8. Plug the adapter into the indoor domestic power supply. Plug! DOORBELL INSTALLATION COMPLETED! Refer to the Abridged user’s manual for common settings and operations.
Detach doorbell from wall mount cover After an extended exposure to cold, heat or humidity, the doorbell gasket rubber may become sticky. If you need to remove the doorbell from its wall mount cover in case of battery replacement or doorbell relocation, follow the steps below. 1. Remove the screw at the bottom. Remove the screw 2. Insert a flat-bladed screwdriver between the doorbell and its wall mount cover. Pry open at both sides 3. Pry the doorbell off.
Installing the doorbell with an existing wired doorbell (optional) If you already have a wired doorbell installed, follow the instructions below to install your new IS7121 doorbell unit. 1. Turn off the power supply to the existing wired doorbell. 2. Follow Step 1 through Step 5 in Doorbell wall mount installation from pages 8 to 10. 3. Insert a cross-head screwdriver to the side of the battery compartment on the right, then twist and lift to loosen the screw and the metallic plate.
4. Using another wire, slide one end of the metal part underneath the metallic plate on the doorbell, then connect the other end to the Trans terminal of your chime/buzzer unit of the wired doorbell. Option 1: Ring the front doorbell of the existing wired doorbell and the IS7121 doorbell simultaneously.
Option 2: Ring the rear doorbell of the existing wired doorbell and the IS7121 doorbell simultaneously. Transformer Transformer Rear Trans Front Chime/buzzer of wired doorbell If you do not connect domestic power supply nor install AA batteries to the IS7121 doorbell, only the existing wired doorbell will ring when being pressed. 5. Follow Step 6 to Step 8 in Doorbell wall mount installation on pages 11 and 12 to complete the installation. VTECH TELECOMMUNICATIONS LTD.