User Manual

ManualsBrandsVQ Model ManualsAircraftsCap 10

Table Of Contents

AEROBATIC MODEL

60 Class

90 Class

2-cycle engine

4-cycle engine

INSTRUCTION MANUAL / MONTAGEANLEITUNG

RADIO CONTROLED ALMOST READY-TO-FLY ENGINE POWERED ALL BALSA PLANE

Wingspan approx. 1500mm

Fuselage lenght approx 1205mm

Electric Motor 870 Watt (PULSAR 60)

Glow Engine .61 2T / .91 4T

Radio 5 Channel / 6 Servos

Spannweiter ca. 1500mm

Lange ca. 1205mm

Elektroantrieb 870 Watt (PULSAR 60)

Verbrennerantrieb 10cc 2Takt / 15cc 4Takt

Fernsteuerung 5 Kanal / 6 Servos

SPECIFICATION TECHNISCHE DATEN

Summary of content (12 pages)

PAGE 1
60 Class 2-cycle engine 90 Class 4-cycle engine AEROBATIC MODEL INSTRUCTION MANUAL / MONTAGEANLEITUNG RADIO CONTROLED ALMOST READY-TO-FLY ENGINE POWERED ALL BALSA PLANE SPECIFICATION Wingspan approx. 1500mm Fuselage lenght approx 1205mm Electric Motor 870 Watt (PULSAR 60) Glow Engine .61 2T / .91 4T Radio 5 Channel / 6 Servos TECHNISCHE DATEN Spannweiter ca. 1500mm Lange ca.
PAGE 2
REQUIRED ITEMS / Zum Betrieb wird benotigt 12x6 for .58 - 2 cycle engine 12x7 for .61 - 2 cycle engine 12x7 for .70 - 4 cycle engine 14x6 for .91 - 4 cycle engine Extension for aileron servo.(x2) ESC 80A .58 ~ .61 - 2 cycle Minimum 6 channel radio for airplane with 7 servos .Motor control x1 .Aileron x 2 .Flap x 2 .Elevator x1 .Rudder x1 .70 ~.91 - 4 cycle Motor Brushless 870Watt (PULSAR 60) Li-Po Battery LEMONRC 4500 - 18.
PAGE 3
1- Servo installation / Servoeinbau Plastic back plate BOTTOM VIEW Unteransicht L/R BOTTOM Plastic control horn 2x20mm screw 2x20mm screw 2x20mm screw 2mm 2mm Plastic control horn X ............................4 2x20mm screw .......................8 Linkage Stopper set ......................2 1.2mm Aileron servo extension cord 1-When you are satisfied with the alignment of the control horn mark the mounting hole positions with a felt tipped pen or a pencil.
PAGE 4
- Wheel pants installation / Fahrwerkseinbau L/R Wooden dowel Wooden dowel TOP VIEW CA CA 1 Right ABS gear cover of “L” set 2 REAR FRONT Left ABS gear cover of “L” set “L” For left wing “R”For right wing BOTTOM VIEW Unteransicht L/R 1- Position the landing gear and strap as show. Using the four 3x10mm screws, fasten the landing gear to the bottom of the wing.
PAGE 5
7- Four-stroke engine installation / Einbau Viertarktmotor Throttle push rod Engine X FRONT VIEW In case of four-stroke engine Secure the engine to the engine mounts using fous 3x25mm screws and nuts 8- Two-stroke engine installation / Einbau Zweitarktmotor Engine X Trim the fire wall so that your muffler doesn’t touch with a knife or Dremel FRONT VIEW In case of two-stroke engine Trim the fire wall so that your muffler doesn’t touch with a knife or Dremel Secure the engine to the engine mounts using
PAGE 6
10- Engine installation / Motoreinbau TOP VIEW Draufsicht Cowling mount 04 08 06 081 001 041 021 061 H L 8 6 118 ~ 122mm 2 04 03 02 01 05 4 2 4 6 2 4 6 8 8 2421 01 0 2421 01 0 6 4 8 01 81 81 3 S N 93 33 06 006 005 003 004 001 002 W 6.
PAGE 7
13- Joining the wing Flachenverbindung TOP VIEW Draufsicht Aluminum tube 14- Joining the wing Flachenverbindung TOP VIEW Draufsicht L/R Asemble the Left and Right wing the same way.
PAGE 8
15- Joining the wing / Flachenverbindung 4mm screws & washer ......2 TOP VIEW Draufsicht RIGHT WING HARVEST LEFT WING HARVEST TOP VIEW Draufsicht 16- Horizontal Tail / Hohenleitwerk A Cut away only the film A B A’ B’ B A = A’ B = B’ Cut away only the film Warning: Securely glue together.
PAGE 9
Apply 5 min. A B Epoxy both the top and bottom. 17- Horizontal Tail Hohenleitwerk STABILIZER Plastic control horn Hinge 10mm ELEVATOR ............................2 Plastic back plate ...........................2 2x20mm screw .......................4 When you are satisfied with the alignment of the control horn mark the mounting hole positions with a felt tipped pen or a pencil.
PAGE 10
19- Linkages / Anlenkungen TOP VIEW Draufsicht Elevator pushrod Rudergestange Throttle pushrod Tank Elevator push rod Throttle push rod Connector Linkage stoper X 2 mm 2 mm CA CA 20- Linkages / Anlenkungen Included with the radio set X Rudder servo When you are satisfied with the alignment of the control horn, mark the mounting hole positions with a felt tipped pen or a pencil.
PAGE 11
22- Cockpit / Kabinen Magnetic hatch TOP VIEW Draufsicht 23- Cockpit / Kabinen TOP VIEW Draufsicht 2x10mm screw 3 4 1 5 2 2x10mm screw 1.5mm 24- Cowling installation / Motorhaube 3mm 5mm Fuel tube or nylon tube CA 3x10mm self tapping screw Drill holes for needle valve, exhaust pipe and glow-plug.
PAGE 12
25- Cowling installation / Motorhaube Trim the cowl with a knife or Dremel so that your engine and muffler don’t touch Fix the cowling with the 3x10mm self tapping screws on the cowling mounts.