Assembly Instructions

ManualsBrandsViv + Rae ManualsBaby & KidsAltieri Twin Over Twin 4 Drawer Solid Wood Standard Bunk Bed with Shelves

Page 1 of 11

BUNK SAFETY WARNING

Size of Mattress and Foundation

The length and width of the upper and lower bunk mattress and foundation are as follows :

Width

37 ½”- 38 ½”

52”- 53”

LengthSize

74”- 75”

Twin

Full

Thickness

9 ½” max

You must use only this size mattress.

Ensure thickness of upper and lower mattress and foundation combined does not exceed 9 ½”

and that the mattress is at least 5” below upper edge of guardrails.

This Bunk Bed uses a slat kit for mattress foundation.

Replacement Parts

SAFETY WARNINGS

! !

( 1 )

( 2 )

( 3 )

( 4 )

( 5 )

( 6 )

( 7 )

( 8 )

( 9 )

(10)

(11)

(12)

(13)

Follow the information on the warnings appearing on the upper bunk end structure

and on the carton. Do not remove warning label from bed.

Always use the recommended size mattresses or mattress support, or both,

to help prevent the likehood of entrapment or falls.

Surface of mattress must be at least 5 in. (127mm) below the upper edge of guardrails.

Do not allow children under 6 years of age to use the upper bunk.

Periodically check and ensure that the guardrail, ladder, and other component are

in their proper position, free from damage, and that all connectors are tight.

Do not allow horseplay on or under the bed and prohibit jumping on the bed.

Always use ladder for entering or leaving upper bunk.

Do not use substitute parts. Contact the manufacturer or dealer for replacement parts.

Use of a night light may provide added safety precaution for a child using the upper bunk.

Always use guardrails on both long sides of the upper bunk. If the bunk bed will be placed

next to the wall, the guardrail that runs the full length of the bed should be placed against

the wall to prevent entrapment between the bed and the wall.

The use of water or sleep flotation mattresses is prohibited.

STRANGULATION HAZARD : Never attach or hang items to any part of the bunk bed

that are not designed for use with the bed; for example, but not limited to, hooks, belts

and jump ropes.

Keep these instructions for future reference.

Replacement parts, including additional guardrails, may be obtained from any

dealer

Summary of content (11 pages)

PAGE 1
Size of Mattress and Foundation The length and width of the upper and lower bunk mattress and foundation are as follows : Size Twin Full Length 74”- 75” 74”- 75” Width 37 ½”- 38 ½” 52”- 53” Thickness 9 ½” max 9 ½” max You must use only this size mattress. Ensure thickness of upper and lower mattress and foundation combined does not exceed 9 ½” and that the mattress is at least 5” below upper edge of guardrails. This Bunk Bed uses a slat kit for mattress foundation.
PAGE 2
STAIRCASE BOOKSHELF ASSEMBLY INSTRUCTIONS READY TWIN - TWIN TO ASSEMBLE Thank you for choosing our new bunk bed. This practical design offers the utmost in versatility. Before assembling your staircase bookshelf bunk bed, please read through these instructions carefully and familiarize yourself with the different parts. Please note that you will require a Phillips head screwdriver and an Allen wrench.
PAGE 3
STAIRCASE BOOKSHELF TWIN - TWIN PARTS LIST 02 07 08 07 18 04 05 03 17 04 14 08 06 08 10 06 18 09 13 09 08 12 16 09 11 01 HARDWARE 02 A UPPER PANEL 03 B UPPER PANEL 04 LEFT, RIGHT END CAP 05 SHORT GUARD RAIL 06 LOWER PANEL 07 FRONT, BACK GUARD RAIL 08 LONG RAILS 09 DRAWERS 01 HARDWARE 10 BACK PANEL 11 TOP PANEL 1 12 TOP PANEL 2 13 TOP PANEL 3 14 TOP PANEL 4 15 HAND GUARDRAIL 16 SIDE SHORT GUARDRAIL 17 BACK SHORT GUARDRAIL 01 HARDWARE 18 TWIN SLAT KIT
PAGE 4
STAIRCASE BOOKSHELF TWIN - TWIN STEP 1 Attach the long rails (08) to the upper panels (02)(03), using JCB M6 X 3 1/8” (A) and barrel nut (B). Tighten with the Allen wrench (M). 02 A A B JCB M6 X 3 1/8” 08 A B B 08 Barrel nut B 03 A M B Allen wrench A Adult assembly STEP 2 Lay the twin slat kit (18) onto the bed. Fix in place using wood screws provided in the slat kit box. FOR SLAT KIT ASSEMBLY follow assembly instructions included with slat kit.
PAGE 5
STAIRCASE BOOKSHELF TWIN - TWIN STEP 3 Attach the front, back guard rails (07) to the upper panel assemblies using Allen screw (F). Tighten with the Allen wrench (M). F F 07 F Adult assembly F F 07 F Allen screw 2 3/8 ” F M F Allen wrench F STEP 4 Insert wooden dowel (C) to the locator holes will receive C as shown below. Attach the short guard rail (05) to the left, right end caps (04), using Allen screw (E),Tighten with the Allen wrench (M).
PAGE 6
STAIRCASE BOOKSHELF TWIN - TWIN STEP 5 Attach the short guard rail assemblies to the upper panel assemblies as shown below, using wood screw (I), tighten with the Phillips head screwdriver. (customer supplied) INSIDE VIEW I Adult assembly I I WOOD SCREW 1 1/4” I Customer supplied Note : Screw holes on end caps should face inside section. Phillips head screwdriver SHORT GUARD RAIL ASSEMBLIES STEP 6 Attach the long rails (08) to the lower panel (06) using JCB M6 X 3 ½” (A), and barrel nut (B).
PAGE 7
STAIRCASE BOOKSHELF TWIN - TWIN STEP 7 Lay the twin slat kit (18) onto the bed. Fix in place using wood screws provided in the slat kit box. FOR SLAT KIT ASSEMBLY follow assembly instructions included with slat kit. Adult assembly Customer supplied 18 Phillips head screwdriver STEP 8 Insert metal pins (H) into the holes on top of the lower panels. Lift the upper panels onto the lower panels as shown, and fit the metal pins into the holes in the bottom of the upper panel legs.
PAGE 8
STAIRCASE BOOKSHELF TWIN - TWIN STEP 9 Insert wooden dowel (C) to the locator holes will receive C as shown below. C C C Wooden dowel Adult assembly C 11 C C 12 C C C 13 C C C C 14 C C C C STEP 10 Attach top panels (11)(12)(13)(14) to drawers (09) as shown below. Using allen screw (D).
PAGE 9
STAIRCASE BOOKSHELF TWIN - TWIN STEP 11 Attach drawer assemblies to back panel (10) as shown below. Using allen screw (D). Tighten with Allen wrench (M). 10 D Adult assembly D D D D Allen screw 1 5/8” D M D Allen wrench D D D BACK VIEW STEP 12 Remove drawers and install wood screw (I) to bottom rail as shown below. Tighten with Phillips head screwdriver. (Customer supplied) Reinstall Drawers to drawer box. Attach back short guardrail (17) to drawer assemblies as shown below.
PAGE 10
STAIRCASE BOOKSHELF TWIN - TWIN STEP 13 Attach side short guardrail (16) to the staircase bookshelf assemblies. Using allen screw (E). Tighten with Allen wrench (M). E Adult assembly E 16 E E Allen screw 2 ” M Allen wrench Attach hand guard rail (15) to the staircase bookshelf assemblies. Using allen screw (E)(G). STEP 14 Tighten with Allen wrench (M). Recheck that all screws are tight.
PAGE 11
STAIRCASE BOOKSHELF TWIN - TWIN STEP 15 Move the bunk bed and staircase bookshelf assemblies where you want to place them in the room. Attach staircase bookshelf assembly to the bunk bed assembly as shown below. Fix L bracket (K) to upper, lower bunk panel using wood screws (J) as shown. Fix large L bracket (L) as shown.