Fitness Electronics User Manual
3
STEP
• Slide the console mast cover onto
the console mast.
• Take the wire tie that exits the
bottom of the console mast and wrap
it around the wire harness and heart
rate wires that are sitting in the
console mast bracket on the frame.
Pull the wire tie up through the top of
the console mast so that the wire
harness and heart rate wires exit the
top of the mast.
• Slide the bottom of the console mast
over the frame bracket being careful
not to pinch the heart rate wires or
wire harness. Assure the mast is
positioned correctly by inserting the
Set Screw (M8x10L) through the front
edge of the mast. Tighten with the
5mm T-handle wrench. Secure the
mast to the frame with four bolts
(M8x15L) and four lock washers (SW8).
Tighten with the 5mm T-handle wrench.
• Slide the console mast cover down
so it sits on the frame covers.
• Mount the console mast handlebar
to the console mast with two bolts
(M8x20L) and two lock washers (SW8).
Tighten with the 5mm T-handle wrench.
• With the screwdriver remove the
four bolts on the back side of the
console. Plug in the wire harness and
heart rate wires to the back side of the
console. Mount the console to the
console mast with the four bolts and
screwdriver.
• Remove the water bottle cage bolts
from the backside of the console mast.
Mount the water bottle cage to the
mast with these two bolts and the
screwdriver.
PINK BAG
4
STEP
• Attach the left and right pedals to
the left and right crank arms.
NOTE:
both pedals and crank arms should
be labeled left or right. Tighten with
the included pedal wrench.
• Plug in the power supply to the power
socket on the front side of the bike.
PEDALS
4
STEP
1
STEP
• Slide the Rear Foot into place on the
back end of the frame. Secure the foot
in place to the frame with two bolts
(M8x20L) and two lock washers (SW8)
to the outside holes and with two bolts
(M8x65L) and two lock washers (SW8)
to the inside holes. Tighten with the
5mm T-Handle Wrench.
• Attach each half of the rear foot joint
cover with the M4x10L screw. Tighten
with the screwdriver.
ORANGE BAG
To avoid possible damage to this Fitness Bike, please follow these assembly steps in the correct order.
Before proceeding, find your new Fitness Bike’s serial number located on the front axle tube, and enter
here:
Refer to this number when calling for service, and enter this serial number on your Warranty Card and in
your own records. Be sure to read your Owner’s Guide before using your new Fitness Bike.
If any parts, hardware or tools are missing, please call 1.800.335.4348, Extension 12
NOTE: It is recommended that you apply grease to the threads of each bolt and screw as you assemble
your Fitness Bike to prevent loosening and noise. Also, during each assembly step, ensure that ALL bolts
and screws are in place and partially threaded in before completely tightening any ONE bolt or screw.
Assembly
Guide
R2050 AND R2150
STEP-THRU SEMI-RECUMBENT FITNESS BIKES
2
STEP
• Rotate the handle on the seat frame to
the forward most position. Tighten the
adjustment bolt on the seat frame
bracket with the 5mm T-Shaped wrench.
• Slide the seat frame onto the seat rail.
Attach the seat rail stopper onto the seat
rail with two (M8x25L) bolts and two
lock washers (SW8). Tighten with the
5mm T-handle wrench.
• Connect the heart rate wires in the
seat handlebar to the heart rate wires
coming up from the seat frame.
• Mount the seat handlebars to the seat
frame with four bolts (M8x15L) and four
lock washers (SW8). Tighten with the
5mm T-Handle wrench.
• Mount the seat bottom cushion to the
seat frame with four bolts (M6x35L) and
four arc washers (M6). Tighten with the
4mm L-shaped wrench.
• Mount the seatback cushion to the
seat frame with four bolts (M6x35L) and
four arc washers (M6). Tighten with the
4mm L-shaped wrench.
BLUE BAG
1
STEP
3
STEP
2
STEP
Rear Foot
Console Mast
Cover
Console Mast
Water Bottle
Cage
Console Mast
Bracket
Seat Rail
Stopper
Rear Foot
Joint Cover
Seat Frame
Adjustment Bolt