User's Manual

Introduction
Thanks for choosing the Keyfob of the home security device. This keyfob is a Z-Wave™ enabled device
(interoperable, two-way RF mesh networking technology) and is fully compatible with any Z-Wave™
enabled network. Every main powered Z-Wave enabled device acts as a signal repeater and multiple
devices result in more possible transmission routes which helps eliminate “RF dead-spots”
Z-Wave™ enabled devices displaying the Z-Wave™ logo can also be used with it regardless of the
manufacturer, and ours can also be used in other manufacturer’s Z-Wave™ enabled networks. This
device could help you control the Z-WAVE devices you learned in the gateway or directly in this keyfob
(need association). It is rechargeable portable controller.
Product Description and Specification
Specification:
Package
Content:
Protocol:
Z
-
Wave™
(ZM
5101
N)
Frequency Range:
865.22MHz (ZT1101IN-5)
868.10MHz (ZT1101MY-5)
868.42MHz (ZT1101EU-5)
869.00MHz (ZT1101RU-5)
908.42MHz (ZT1101US-5)
916.00MHz (ZT1101IL-5)
919.80MHz (ZT1101HK-5)
920~923MHz (ZT1101KR-5)
921.42MHz (ZT1101BR-5)
922~926MHz (ZT1101JP-5)
Operating Range: Up to 100 feet line of sight
Operating Temp.: -15°C~ 60°C (5°F ~140°F)
Battery: Lithium-Ion Rechargeable Battery (220mAh)
1pc
1pc
1pc
Keyfob
Installation & Operation manual
Micro USB/USB cable
Z-Wave Supported Command Classes:
COMMAND_CLASS_ASSOCIATION_GRP_INFO
COMMAND_CLASS_ ASSOCIATION_V2
COMMAND_CLASS_ BATTERY
COMMAND_CLASS_CENTRAL_SCENE
COMMAND_CLASS_DEVICE_RESET_LOCALLY
COMMAND_CLASS_FIRMWARE_UPDATE_MD_V2
COMMAND_CLASS_MANUFACTURER_SPECIFIC_V2
COMMAND_CLASS_POWER_LEVEL
COMMAND_CLASS_VERSION_V2
COMMAND_CLASS_WAKE_UP_V2
COMMAND_CLASS_ ZWAVEPLUS_INFO_V2
Installation/Operation
Notice: If you are installing the entire Z-Wave™ system for the first time, please refer to
the installation guide of Z-Wave™ Interface Controller before installing keyfob.
1. There's a DIP switch at the bottom of keyfob. Different positions
corresponds to different functionalities that described in the following
sections
2. Setup Z-Wave Network:
A) To “Include” into (adding into) or “Exclude” from (removing from) an existing
network: Put the Z-Wave™ Gateway or Controller into learn mode to add or remove
the keyfob into/from your controller. To get in to “inclusion” or “exclusion” mode, the
distance between sensor and controller is suggested to be within one meter. (See
3.Control Mode: 1)Learn Mode & 4.Setup Mode: 5)Learn Mode via NWI)
B) Association Set From Gateway/Primary Controller:
* Keyfob supports 5 groups; group 1 (Lifeline) – “Central Scene”, group 2~5 (Scene
Activation).
* Primary Controller or Gateway could association nodes to all its groups 1~5.
C) Keyfob can form its own network. In this case it's role is primary controller and
capable of include/exclude other devices or controllers into its own network. It can also
organize its Scene Activation Groups 2~5.(See 4.Setup Mode). It can also hand over
its primary role to other controllers in network by Controller Shift (See 4.Setup Mode).
D) When Keyfob's role is secondary controller, it can become primary controller by
entering learn mode while Primary Controller uses its controller shift function.(please
refer to its manual for detail).
3. Control Mode (DIP SWITCH TO RIGHT):
1) Learn Mode:
* Keyfob should not include any node
* Press button 1 and 4 together till the red LED flashes to
* Keyfob will return to sleep after 5 seconds if no inclusion nor exclusion.
2) Wake Up Notification
Press button 2 and 3 together until green LED flashes. Keyfob will first send NIF
(without entering learn mode) and then send Wakeup Notification 5 seconds later.
3) Wake Up Interval
Use Wakeup Interval Set command to set wakeup time to send “Wake Up
Notification” to assigned node. User could change the auto wake up from 4
minutes to 1 week. The minimal increment interval is 4 minutes.
* Default Value: 6 hours
4) Battery Capacity Detection:
* Send “Battery Get” command, and then wake up device as described in 2)
above, to have the battery capacity back in %.
* It will detect the battery capacity automatically every 2 hours.
* Low Battery Auto Report to Group 1 (Lifeline) Nodes.
* Full Capacity: 0x64 / Low Battery Warning: 0xFF
و
ﻮ

و

4