Installation Instructions

ManualsBrandsViking ManualsDowndraftsViking 48" Professional 5 Series Stainless Steel Rear Downdraft

MODEL

VEDV900

EXTERIOR

BLOWER

10" ROUND DUCT

DOWNDRAFT

WARNING

READ AND SAVE THESE INSTRUCTIONS

MODEL VDVE900

EXTERIOR MOUNTED BLOWER

FOR USE WITH MODELS VDD5300, CVDD5300, VDD5360, CVDD5360, VDD5450,

CVDD5450, VDD5480, CVDD5480 DOWNDRAFT VENTILATORS.

TO REDUCE THE RISK OF FIRE, ELECTRIC

SHOCK, OR INJURY TO PERSONS, OBSERVE

THE FOLLOWING:

1. Use this unit only in the manner intended by the

manufacturer. If you have questions, contact the

manufacturer or your distributor.

2. Before servicing or cleaning unit, switch power off

at service panel and lock the service disconnect-

ing means to prevent power from being switched

on accidentally. When the service disconnecting

means cannot be locked, securely fasten a prom-

inent warning device, such as a tag, to the service

panel.

3. Installation work and electrical wiring must be done

by a qualified person(s) in accordance with all ap-

plicable codes and standards, including fire-rated

construction codes and standards.

4. Sufficient air is needed for proper combustion and

exhausting of gases through the flue (chimney) of

fuel burning equipment to prevent backdrafting. Fol-

low the heating equipment manufacturer's guideline

and safety standards such as those published by

the National Fire Protection Association (NFPA),

and the American Society for Heating, Refrigeration

and Air Conditioning Engineers (ASHRAE), and

the local code authorities.

WARNING

CAUTION

1. For general ventilating use only. Do not use to ex-

haust hazardous or explosive material and vapors.

2. To avoid motor bearing damage and noisy and/or

unbalanced impellers, keep drywall spray, con-

struction dust, etc. off power unit.

3. Please read specification label on product for further

information and requirements.

4. Electrical circuit, including speed control, (if used),

must be rated 6 AMPS minimum.

Blower Dimensions

28.25 x 24.75 x 7.17

PLAN THE

INSTALLATION

1. Locate the blower so the

length of the duct run and

number of elbows needed

are kept to a minimum.

2. Where possible, blower

should be centered between

wall studs or roof rafters.

3. Avoid pipes, wires, or other

ductwork that may be run-

ning through the wall.

ALL INSTALLATIONS

MODEL VOLTS AMPS CFM DUCT SIZE

VDVE900 120 5.7 900 10 " DIA.

SPECIFICATIONS

5. When cutting or drilling into wall, or ceiling, do not

damage electrical wiring or other hidden utilities.

6. Ducted fans must always be vented to the outdoors.

7. To reduce risk of fire, use only metal ductwork.

8. This unit must be grounded.

MODEL VEDV900

EXTERIOR BLOWER

10" ROUND

DUCT

DOWNDRAFT

TYPICAL ROOF MOUNTED INSTALLATION

TYPICAL

WALL MOUNTED INSTALLATION

INSTALLER: Leave This Manual With The Homeowner

HOMEOWNER: Use And Care Information On Page 4

MODEL VDVE900

EXTERIOR BLOWER

MODEL

VDVE900

EXTERIOR

BLOWER

Summary of content (12 pages)

PAGE 1
MODEL VDVE900 EXTERIOR MOUNTED BLOWER FOR USE WITH MODELS VDD5300, CVDD5300, VDD5360, CVDD5360, VDD5450, CVDD5450, VDD5480, CVDD5480 DOWNDRAFT VENTILATORS. READ AND SAVE THESE INSTRUCTIONS WARNING WARNING TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING: 1. Use this unit only in the manner intended by the manufacturer. If you have questions, contact the manufacturer or your distributor. 2.
PAGE 2
PREPARE THE INSTALLATION LOCATION PREPARE THE INSTALLATION LOCATION ROOF INSTALLATIONS WALL INSTALLATIONS 1. Locate the blower on the rear slope of the roof. Place it in a location to minimize duct run. The location should be free of obstacles (T.V. leads, electrical lines, etc.). Bear in mind, if the blower top is level with the roof peak, it will not be seen from the street. Keep this approximate location in mind as you work from within the attic. 1. Choose a position on the outside wall.
PAGE 3
INSTALL THE BLOWER INSTALL THE BLOWER ROOF INSTALLATIONS WALL INSTALLATIONS 1. Remove roofing nails from the upper 2/3 of the shingles around the cutout area and carefully lift the shingles to allow the back flashing sheet on the blower housing to fit under them. 1. Place a large bead of caulk on the back side of the housing along the outer edge. 2. Center the blower ring in the 11" diameter hole, making sure that the 1-1/4" diameter electrical wiring hole aligns with the hole in the wiring box. 2.
PAGE 4
CONNECT 10" ROUND DUCTWORK USE AND CARE 1. Connect 10" round ductwork to blower. Run ductwork to downdraft location. Disconnect electrical power supply and lock out service panel before cleaning or servicing this unit. 2. Refer to downdraft ventilator manual for instructions on how to: Locate and cut holes in cabinet. Attach 10" round duct and rough-in plate to downdraft. CLEANING Remove cover and carefully vacuum blower and inside of housing. Be careful not to bend or otherwise damage blower wheel.
PAGE 5
MODÈLE VDVE900 VENTILATEUR MONTÉ À L’EXTÉRIEUR POUR UTILISATION AVEC LES MODÈLES VDD5300, CVDD5300, VDD5360, CVDD5360, VDD5450, CVDD5450, VDD5480, CVDD5480 VENTILATEURS À TIRAGE VERS LE BAS SEULEMENT VEUILLEZ LIRE CES DIRECTIVES ET LES CONSERVER AVERTISSEMENT AVERTISSEMENT OBSERVEZ LES DIRECTIVES CI-DESSOUS DE MANIÈRE À RÉDUIRE LES RISQUES D’INCENDIE, DE CHOC ÉLECTRIQUE OU DE BLESSURES CORPORELLES. 1. N’utilisez cet appareil que de la manière prévue par le fabricant.
PAGE 6
PRÉPARATION DE L’EMPLACEMENT DE POSE PRÉPARATION DE L’EMPLACEMENT DE POSE POSES SUR LES TOITS POSES SUR LES MURS 1. Choisissez un emplacement de pose pour le ventilateur sur la pente arrière du toit. Placez-le dans un emplacement réduisant au maximum l’utilisation de conduits. Cet emplacement doit être exempt d’obstacles (fils de téléviseur, lignes électriques, etc.) Rappelez-vous que si le dessus du ventilateur affleure le faîte du toit, il ne pourra être aperçu de la rue.
PAGE 7
POSE DU VENTILATEUR POSE DU VENTILATEUR POSES SUR LES TOITS POSES SUR LES MURS 1. Retirez les premiers deux tiers des clous à toiture des bardeaux se trouvant autour de la surface de découpe puis soulevez délicatement les bardeaux de manière à permettre à la feuille de tôle noire de s’y glisser. 1. Appliquez une large bande de produit à calfeutrer à l’arrière du boîtier, le long du rebord extérieur. 2.
PAGE 8
RACCORDEMENT DU CONDUIT ROND DE 25,4 CM (10 PO) 1. UTILISATION ET ENTRETIEN Débranchez l’alimentation électrique et verrouillez le panneau d’entrée d’électricité avant de nettoyer ou de réparer l’appareil. Raccordez le conduit rond de 25,4 cm (10 po) au ventilateur. Faites cheminer les conduits vers l’emplacement du ventilateur à tirage vers le bas. NETTOYAGE Retirez le couvercle et passez soigneusement l’aspirateur à l’intérieur du boîtier. Veillez à ne pas courber ou endommager la roue du ventilateur.
PAGE 9
VENTILADOR DE MONTAJE EXTERIOR MODELO VDVE900 PARA USARSE ÚNICAMENTE CON EL VENTILADORS DE TIRO DESCENDENTE MODELOS VDD5300, CVDD5300, VDD5360, CVDD5360, VDD5450, CVDD5450, VDD5480, CVDD5480. LEA Y CONSERVE ESTAS INSTRUCCIONES ADVERTENCIA ADVERTENCIA PARA REDUCIR EL RIESGO DE INCENDIOS, DESCARGAS ELÉCTRICAS O LESIONES PERSONALES, OBSERVE LAS SIGUIENTES PRECAUCIONES: 1. Use la unidad sólo de la manera indicada por el fabricante. Si tiene preguntas, comuníquese con el fabricante o el distribuidor. 2.
PAGE 10
PREPARE EL LUGAR DE LA INSTALACIÓN PREPARE EL LUGAR DE LA INSTALACIÓN INSTALACIONES EN EL TECHO 1. Ubique el ventilador en la pendiente posterior del techo. Colóquelo en un área en la cual minimice la longitud del tramo de conducto. Esta área debe estar libre de obstáculos (cables de T.V., cables eléctricos, etc.). Si la parte superior del ventilador está al ras del pico del techo, no se verá desde la calle. Tome en cuenta esta ubicación aproximada mientras trabaja desde el ático.
PAGE 11
INSTALE EL VENTILADOR INSTALE EL VENTILADOR INSTALACIONES EN EL TECHO INSTALACIONES EN LA PARED 1. Quite los clavos del techo de las 2/3 partes superiores de las tejas que se encuentran alrededor del área de corte y levante las tejas con cuidado para permitir que la hoja cubrejuntas posterior de la cubierta del ventilador se ajuste debajo de ellas. 1. Coloque un reborde grande de material de calafateo en el lado posterior de la cubierta, a lo largo del borde externo. 2.
PAGE 12
CONECTE EL CONDUCTO REDONDO DE 10 PULG. (25 CM) 1. USO Y CUIDADO Desconecte el suministro eléctrico y bloquee el panel de servicio antes de limpiar o dar servicio a esta unidad. Conecte el conducto redondo de 10 pulg. (25 cm) al ventilador. Tienda el conducto hasta el sitio del tiro descendente. LIMPIEZA Quite la cubierta y cuidadosamente aspire el ventilador y el interior de la cubierta. Tenga cuidado de no doblar la rueda del ventilador ni dañarla de alguna otra manera. 2.