Installation Guide

ManualsBrandsVeranda ManualsFencingDover 6 ft. H x 8 ft. W White Vinyl Privacy Fence Panel

A general rule of thumb is to place 1/3 of the post into the ground.

Check local regulations for any special requirements. The fence

will be stronger if the end, corner and gate posts are set at least

6" deeper than the line posts. Using a posthole digger or power

auger, dig the holes 10-12" wide and 6" deeper than needed.

Backﬁll the holes with 6" of gravel to drain water away from the

bottom of the posts (ﬁg. 1). Keep the height of your fence panels

in mind when digging your postholes.

Starting in the corner, mix concrete in the ﬁrst hole per the

instructions on the bag. Mix thoroughly and install the post into

the hole and tap the post to the proper depth. We recommend a

2" gap from the ground to the bottom of the panel. Use a level to

ensure the fence post is plumb and the post is square with the

ground. Brace the post with temporary supports as the concrete

sets (per the instructions).

Check local ordinances and regulations before building your

fence. Before construction, contact your local utility companies

to mark any underground cables and pipelines. In addition, it is

a good idea to discuss plans with any neighbors along your

proposed fence line.

Step 3Preparation

Digging postholes

• Determine the number of posts, panels and gates needed to

complete the job based on the total linear footage. Take into

consideration post, panel and gate widths when determining

the total number of each.

• Adjust layout to accommodate as many full panels as possible.

If you must use a partial panel, place it in the farthest rear

corner of the property.

• Locate property boundaries and drive stakes into the ground

at corners and ends of fence line, based on local municipality

regulations.

• Stretch twine or heavy string between stakes and pull tight

to mark layout of fence line.

• Be sure to measure your fence panels and gates prior to

determining the location of the postholes. Place posts in the

following order along string line:

• End/corner posts • Gate posts • Line posts

Design and layout

36" to 42"

10" to 12"

Diameter

Level

Fig.4.pdf

ﬁg. 1

6X8 DOVER PRIVACY PANEL

ASSEMBLY INSTRUCTIONS

Items you may need

• Fence posts*

• Posthole digger

• Measuring tape

• Clear PVC cement

• Drill

• Screwdriver

• Level

• Chop saw

• String line

• Fast-setting

Concrete

• Gravel

• Shims

• Pencil

• Safety glasses

• Gloves

* One per panel, plus one to complete the fence run

Kit contents

• 10 — Panel pickets • 2 — Rails

Actual Panel Size: 69.57" H x 90.605" W

Post Spacing: 90.605" inside to inside

90.605" W

94.5" Rail Width

69.57" H

68956 U.S. Hwy 131, White Pigeon, MI 49099 616.365.4201 9008_8/16

www.ufpi.com

Summary of content (6 pages)

PAGE 1
6X8 DOVER PRIVACY PANEL ASSEMBLY INSTRUCTIONS Items you may need 94.5" Rail Width • Fence posts* • Screwdriver • Gravel • Posthole digger • Level • Shims • Measuring tape • Chop saw • Pencil • Clear PVC cement • String line • Safety glasses • Drill • Fast-setting Concrete • Gloves 69.57" H * One per panel, plus one to complete the fence run Kit contents • 10 — Panel pickets • 2 — Rails Digging postholes 90.605" W Actual Panel Size: 69.57" H x 90.605" W Post Spacing: 90.
PAGE 2
6X8 DOVER PRIVACY PANEL ASSEMBLY INSTRUCTIONS, CONTINUED Assembling the panel STEP 1 Install first post with concrete (See “Digging postholes” and fig. 1). STEP 2 Slide the bottom rail into place at the bottom of the routed post (fig. 2). STEP 3 Install the second post into the ground and temporarily secure into place. Set the bottom rail into the second post and level. (You will secure the second post with concrete in Step 5.) (fig. 3). fig.
PAGE 3
PANNEAU ISOLANT DOVER 6 X 8 INSTRUCTIONS D’ASSEMBLAGE Articles dont vous pourriez avoir besoin H de 176,71 cm (69,57 po) Largeur de la traverse 240,03 cm (94,5 po) • Poteaux de clôture* • Tournevis • Gravier • Tarière • Niveau • Cales • Ruban à mesurer • Scie à tronçonner • Crayon • Ciment PVC transparent • Ligne du cordeau • Lunettes de sécurité • Perceuse • Béton à prise rapide • Gants *Un par panneau, plus un pour compléter la longueur de la clôture.
PAGE 4
PANNEAU ISOLANT DOVER 6 X 8 INSTRUCTIONS D’ASSEMBLAGE Installation du panneau ÉTAPE 1 Installez le premier poteau avec du béton (« Creuser les trous de poteaux » et fig. 1). ÉTAPE 2 Glissez la traverse inférieure et mettez-la en position au bas du poteau acheminé (fig. 2). ÉTAPE 3 Installez le deuxième poteau dans le sol et fixez-le temporairement en position. Installez la traverse inférieure dans le deuxième poteau et mettez à niveau. fig.
PAGE 5
INSTRUCCIONES DE ARMADO DEL PANEL DE PRIVACIDAD DOVER Artículos que puede necesitar: 176.71 cm (69.57 pulg) de altura Separación entre rieles de 240.03 cm (94.5 pulg) • Postes para cerca* • Nivel • Lápiz • Excavadora para postes • Sierra ingletadora • Lentes de seguridad • Cinta de medir • Concreto de secado rápido • Cemento claro para PVC • Taladro • Destornillador • Cordel para marcar • Grava • Guantes *Uno por panel, más uno para terminar el tramo de cerca.
PAGE 6
INSTRUCCIONES DE ARMADO DEL PANEL DE PRIVACIDAD DOVER Armado del panel PASO 1 Instale el primer poste con concreto (“Excavación de agujeros para postes” y fig. 1). PASO 2 Deslice el riel inferior en su sitio en la parte inferior del poste ranurado (fig. 2). PASO 3 Instale el segundo poste en el piso y sujételo temporalmente en su sitio. Sujete el riel inferior al segundo poste y nivélelo. (Lo sujetará con concreto en el Paso 5.)(fig. 3). fig.