Owner`s manual

9
au la a~~al ~ed aU!e~1 au alqe:J un:Jne,nb la sauna} ualq lUOS
suoll:Jauuo:J sal saJnOI anb snoll-za~nsstf ·~IOU s~all Ulle6fJu)
~loU la ' a6no~ s~all (1ll!sod) a6nolJ ·suoll:Jauuo:J sal Salle}
snoll anbs~ol fJlpelOd auuoq el ~lualufBw ap snOIl-zamsse
' ledl:Jul~d ~nale:Jll!ldwe a~IOIl ~a6ewwopua,p ~allllfJ,p uliV
jjjUollUallV
·alu la~ua , 1 ~ahll malll~!j!ldwil aJlOh lCl ualq
no malda~\lJ aJ I Oh 111UaWalOaJ!p Sa!!lIalllS SOh JalOaUUO~ zahnod
snOh ' aUJalU! lnll4-asslld amdno~ III JaUmOlUOO za!!1l4nos snOh !S
·saouanbl'Jj
salnll4
ap UO!lOnpoJdaJ III lCl aOl; 1J5 I'llIllnb amall!aw aun J!umoj
ap l
aWJad mal !nb a~ la 'smaplld-lnll4 SOli ap samap\ljul sassllq
sal aU l wll\l lnb ao ' (OO~-l:) al mod ZHSB no) ZHOO~ / OB 11 s\ldnoo
lUOJaS a!!lIalllS smajJlld-lne4 SOli 'apo411'W allao zailins snOh !S
·\l J5\lIU I
malllOljlldwe
aJlOIl lCl no malda~I'J aJIOIl 111uawalOaJ 1P aUApola/\
alu!aOua aJIOIl JalOaUUO~ ap aldw!s UO~llj aun aJIUOW (: am5!j III
,mr3/Jed-lneL/ ner3"!U UO!l:Jr3UU0:J
·a:luewJojJad aJnall!aw aun Jnod a!'J6!'lU! amdno:l III Jas!I!ln,p
!'lI!asuo:l lsa I! 'aUJalXa amdno:l ap sed zas!I!ln,u snoll IS
···anbJewal::l
·IIlU51S np aJ!olOafeJI el ap aUJalUl
aJndnoo el Jau!wlI!',P lauuad a5e 15'1J a:) . ..LflO. ms JaUUO!l!sod alia
alu!aOua,1 ap aJ'1~Je,llCl \In!ls .NI-.LnO 'JallO-X. a5e15'1J ap uOlnoq al
Jas lle:xJ 1 'amd no~ aJlne aun,p seq-assed leu5!s un !!OOaJ alla,nbSJol
sasseq sawi!JjXa,p aIU ! a~Ua , 1 ap awalu l amdnoo el JaWnOIUo~ mOd
·wnWl xew a~uewJOllad
aun JlIqlll\lJ ap laWJad (ZH 0(: ~ anb allal) a\lllal\l snld ~uanb\lJj
aun 11 amdno~ aun JaI5'1J ap !!ej Inas al 's uollellelsul saulejJao
sueo ·auApola/\ alula~ua , 1 suep !los 'massa~Jd al suep !los aWalU!
amdno~ el JaWnOIUO~ za!lIap snoll anb lnad as I! 'uollellelsul,p
adJlj a~ sueo ·!lnJq ap snld dno~neaq Ja \lJ~ la a~UeW JOll ad ap
external crossover and the
one internal to the subwoofer may result
in low output and increased noise. In these installations you may
need to bypass the internal crossover in either the processor or
Velodyne subwoofer. In some installations, simply setting one
crossover to a higher frequency (such as
120 Hz) will restore
maximum performance.
To bypass the
subwoofe~s internal crossover when the unit is
being fed a low pass signal from another crossover, simply locate
the switch marked X-over,
OUT - IN on the rear panel of the
subwoofer and set to the
OUT position. This will eliminate the
internal crossover from the signal path.
Note ...
If not using an external crossover , you should use the built-in
crossover for optimal performance.
Speaker-level connection
Figure 2 shows an easy way to connect your Velodyne subwoofer
directly to your receiver or integrated amplifier.
When connected in this fashion, your
satellite speakers will be
crossed over at
80 /1 OOHz (or 85Hz forCT-100), which removes the
lower bass from your speakers, enabling them to do a better job
reproduci
ng high frequencies. .
You may also connect your satellites directly to your receiver or
amplifier along with the subwoofer if you wish to bypass the internal
high-pass crossover.
Caution!!!
To avoid damage to your main amplifier , be sure to maintain
correct polarity when making all connections. Red (positive)
to red, and black (negative) to black. Be sure that all connections
are tight, and that there are no loose strands or frayed wires_
OOI'lt.nueo: .•
6