Wet/Dry Vacuums Operator’s Manual Floor Vac Model No. VF408 FOR YOUR SAFETY Read and understand this manual before use Keep this manual for future reference www.vacmaster.com Cleva North America 44 Parkway Commons, Greer, SC 29650 Part No. VH60BZ.20.60.
TABLE OF CONTENTS SECTION PAGE Warranty………………………………………………………………………………………………. 2 Safety Instructions and Warnings………………………………………………………………….. 3 Double Insulation Instructions....…………………………………………………………………… 4 Extension Cord………………………………………………………………………………………. 4 Unpacking and Checking Carton Contents………….……………………..………………………5 General Assembly Instructions……………………………………………………………………... 6 Dry Vacuum Operation……………………………………………………………………………….
SAFETY INSTRUCTIONS & WARNINGS IMPORTANT SAFETY INSTRUCTIONS Read and understand all instructions before using this vacuum Read and understand this owner’s manual and all labels on the Wet/Dry Vacuum cleaner before operating. Safety is a combination of common sense, staying alert and knowing how your vacuum works. Use this Wet/Dry Vac only as described in this manual. To reduce the risk of personal injury or damage to your Wet/Dry Vac, use only Vacmaster™ recommended accessories. For Household Use Only.
DOUBLE INSULATION INSTRUCTIONS This Wet/Dry Vac is double-insulated, eliminating the need for a separate grounding system. Use only identical replacements parts. Read the instructions for Servicing Double-Insulated Wet/Dry Vacs before servicing. Use this Wet/Dry Vac as described in this manual. Observe the following warnings that appear on the motor housing of your Wet/Dry Vac. DOUBLE INSULATED - GROUNDING NOT REQUIRED - WHEN SERVICING USE ONLY IDENTICAL REPLACEMENT PARTS.
Remove entire contents of carton. Check each item against the carton contents list. Carton contents lists Key Description……………………..…… Qty A B C D E F G H I J K L M N O P Q R S Vac Assembly…………………….…..1 Hose…………………….……………..1 2-in-1 Utility Nozzle……….………….1 Round Dust Brush………………….. 1 Crevice Tool………..…………………1 Floor Combo Nozzle…………..…......1 Cartridge Filter……………………… 1 Filter Retainer………...……………… 1 Dust Bag………….……………….…. 1 Foam Sleeve Filter……..……...........
GENERAL ASSEMBLY INSTRUCTIONS A Philips head screw driver is required. WARNING: DO NOT PLUG IN POWER CORD TO POWER OUTLET, MAKE SURE PLUG IS DISCONNECTED BEFORE ASSEMBLING THE WET/DRY VAC. UNPACKING YOUR WET/DRY VACUUM & GENERAL ASSEMBLY 1. Verify that the power cord is disconnected from the outlet. (fig. 1) 2. Undo the latches. (fig. 2) 3. Lift the power head off the container. (fig. 3) 4. Remove the contents from inside the container, make sure you have all contents as listed on page 5. (fig. 4) 5.
POLARIZED PLUG To reduce the risk of electrical shock, this appliance has a polarized plug (one with the blade wider than the other). This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install the proper outlet. Do not change the plug in any way. Double insulation eliminates the need for the three wire grounded power cord and grounded power supply system.
LIQUID VACUUM OPERATION LIQUID VACUUMING WARNING: BE SURE TO READ, UNDERSTAND, AND APPLY INFORMATION, ENTITLED ‘SAFETY INSTRUCTIONS & WARNINGS’. DO NOT VACUUM IN AREAS WITH FLAMMABLE GASES, VAPORS, OR EXPLOSIVE DUSTS IN THE AIR. FLAMMABLE GASES OR VAPORS INCLUDE BUT ARE NOT LIMITED TO; LIGHTER FLUID, SOLVENT TYPE CLEANERS, OIL-BASE PAINTS, GASOLINE, ALCOHOL OR AEROSOL SPRAYS. EXPLOSIVE DUSTS INCLUDE BUT ARE NOT LIMITED TO; COAL, MAGNESIUM, GRAIN OR GUN POWDER.
MAINTENANCE 1. Verify that the power cord is disconnected from the outlet. (fig.1) 2. Disconnect the hose from the vacuum. (fig. 2) 3. Undo the latches and remove the power head from the container. (fig. 3) 4. Clear all dirt or debris from the container and hose. (fig. 4) 5. Clean the foam filter by washing it with water and mild soap. (fig. 5) 6. Check the hose, attachments, and power cord to verify that they have not been damaged.
Installing and Cleaning HEPA Filter 1. 2. 3. 4. 5. 6. Verify that the power cord is disconnected from the outlet. (fig.1) Unlock the filter door by lifting the lock tab UP to the unlocked position and pull the door out. (fig. 2 & 3) Remove the HEPA filter cartridge from the vacuum. (fig.4) Clean filter by brushing dirt off. For optimal performance a new filter is recommended. (fig.5) Install the cleaned or new filter into place. (fig.
TROUBLESHOOTING WARNING! TO REDUCE THE RISK OF ELECTRIC SHOCK-UNPLUG BEFORE TROUBLESHOOTING Symptom Possible Causes Corrective Action Vacuum will not operate 1) No power supply. 1) Check power supply – cord, breakers, fuses. 2) Unplug and check the power cord. If damaged, have it repaired by a professional. 3) Empty container. 1) Attach or replace cartridge filter. 2) Faulty power cord. Dust comes out from motor cover. Reduced efficiency and motor/speed vibration. 3) Container full.
EXPLODED VIEW AND PARTS 12