Freestanding Bathtub Installation and Care Guide Features: - Contemporary Freestanding Design - Integrated Overflow System - Adjustable Feet for Easy Installation Materials: - Acrylic / Fiberglass Composite Luxier 1-877-711-8828 support@luxierusa.com Luxier 1 082019 Rev.
Thank you for purchasing Luxier products. Please read the information below and keep this installation guide for future reference. If you require assistance, please contact our customer service department at 1-877-711-8828, Monday - Friday 9 AM - 5 PM Pacific Time or by email at support@luxierusa.com. Before You Begin IMPORTANT: • Read and understand this installation guide completely before installation. It will increase the chance of a successful installation.
Important Safety Instructions Risk of Personal Injury! Bathtub may become slippery when wet. Exercise caution when entering and exiting the bathtub. Do not overfill the bathtub before entering. Overfilling will cause overflow and slippery conditions. Risk of Drowning! Do not leave children unattended when using the bathtub. Supervise small children at all time when using this bathtub. Risk of Personal Injury! Accidental falls may occur.
Installation - Site Preparation • • • • Provide sufficient floor support. Check the floor at the installation site and make repairs as needed. Waterproof the floor is highly recommended. Finished floor must be level. Provide adequate clearance on all sides of the bathtub. Minimum of 2 inch waste drain pipe is required. Installation - Drain Assembly NOTICE: It is recommended to dry fit the parts before installation. 1. Place a large drop cloth on the floor to protect the bathtub. 2.
Installation - Bathtub CAUTION: Risk of Personal Injury. Get extra help when moving the bathtub into its final position. 1. Use a level to make sure the bathtub is level in all direction. (Fig. 2) 2. Adjust the feet under the tub as needed. 3. It is recommended to leave a 1/16” to 1/8” gap all around the base of the bathtub. 4. Close the drain and remove any debris or plastic films from the tub. Wipe the surface clean with a piece of soft cloth. 5.
Warranty Thank you for purchasing Luxier products. Please read the information below and keep this installation guide for future reference. If you require assistance, please contact our customer service department at 1-877-711-8828, Monday - Friday 9 AM - 5 PM Pacific Time. Or by email at support@luxierusa.com.
Freestanding Floor Mount Bathtub Filler Model Number: FTF01-TB FTF01-TC Features: - Brass and Zinc Alloy Construction Single Hole Installation Drip Free 40 mm Ceramic Cartridge Hand shower flow rate 1.8 gpm at 80 psi Tub spout flow rate 3.7 gpm at 20 psi Rough-in kit included - Complies with: IAPMO / UPC / cUPC ADA 27 3/4” 32” 38 1/8” 43 1/16” 8 1/8” 2” 3 11/16” 5 1/2” 1/2 NPT * All Measurements are Approximate * Luxier 1 4 5/16” FTF01 Rev.
Thank you for purchasing Luxier products. Please read the information below and keep this installation guide for future reference. If you require assistance, please contact our customer service department at 1-877-711-8828, Monday - Friday 9AM - 5PM Pacific Time or by email at support@luxierusa.com. Limited Lifetime Warranty (For USA Only) The manufacturer warrants this product to be leak and drip free during daily normal household use for as long as it is owned by the original purchaser of this product.
Important Points • This installation guide is subject to change without notice, please contact us to request the most updated version of this installation guide. • This is a general installation guideline, actual installation may vary. Consult a professional if necessary. • Read and understand this instructions completely before installation. • Please follow all local building and plumbing codes. • Product drawings in this installation guide is for illustration purpose only.
Installation 1 2 2 1 5 1 Top Riser Tube 2 3 4 Bottom Riser Tube Cartridge Stem 5 4 6 3 1. Insert the RISER TUBE (1) over hot and cold SUPPLY HOSES (5). Thread the Top RISER TUBE (1) into base of the VALVE BODY (2) and tighten it fully. Slide the FLOOR MOUNTING FLANGE (3) onto the Bottom RISER TUBE with the flange (4). Thread RISER TUBE (4) into the bottom of RISER TUBE (1) and fully tighten the tubes.
Installation 4. With the Tub Filler Assembly aligned in the desired position, mark each of the 4 mounting holes from the Mounting Flange (1) on the floor. 4 1 4-1. Use a drill with 1/4” drill bit, drill the holes 1 3/4” deep and insert the included Anchors (2). Make sure the Anchors are flush with the finished floor. 4-1 2 5. Make sure both Hot and Cold water supply hoses pass through the 2” mounting hole with at least 1 1/4” of the hose in the floor space.
Installation 7. Hold the Tub Filler Assembly (1) in place and install the four Mounting Screws (3). Check aligment and level before fully tightening the Mounting Screws (3). After tightening the screws slide the Escutcheon (2) down to cover the flange. 7 1 2 3 COLD HOT 8 8. Connect the Hand Shower Hose (5) to the Tub Filler. Use an adjustable wrench to connect the Hand Shower Hose (5) with hex nut end to the Tub Filler.
Operations Front View Diverter Knob To operate the tub filler simply move the handle to the ON position to turn on the water. Adjust the temperature by moving the handle from side to side to set the desired water temperature. Side View OFF ON HOT COLD To operate the hand shower wand, remove the hand shower from its holder and direct the jets into the tub. Pull the diverter knob on the faucet body. Push the diverter knob to direct the water back to the spout. Parts 01. Aerator Assembly 02.
