Installation Guide

Hydraulic Gate Closer
TB200, TB400, TB600
Installation Instructions
INSTALLATION INSTRUCTIONS:
36” Gate
Gate Closer
Added Opening Force
48” Gate 60” Gate
3/4 lb. 1/2 lb. 1/4 lb.
No Closer
6 lbs. 4 lbs. 3 lbs.
TB200
10 lbs. 8 lbs. 6 lbs.
TB400
13 lbs. 10 lbs. 8 lbs.
TB600
Added Force at 45 degrees Open
7 lbs. 5 lbs. 4.5 lbs.
TB200
13 lbs. 9.5 lbs. 8 lbs.
TB400
18.5 lbs. 13.5 lbs. 12 lbs.
TB600
Constant
Closing
Pressure
45 lbs.
0 lbs.
90 lbs.
135 lbs.
36-52 Inches
Approximate
Width
40-64 Inches
44-72 Inches
50-125 lbs.
Approximate
Weight
75-175 lbs.
150-250 lbs.
Step 1: Secure Post Bracket (#2) to Gate Post *This step is the MOST important. The Post Bracket (#2) MUST be mounted first.*
Hold Post Bracket (#2) to the face of the gate post.
Measure from the center of the first hole on Post Bracket (#2A) to the center of the Hinge Pin .
This measurement MUST be between 2” and 4”.
Clamp bracket into place.
Note: Regardless of hinge arrangement, the measurement from the center of the Hinge Pin to the center of hole 2A on Post Bracket (#2)
must not exceed 4” or damage to the gate closer may occur.



Gate
Post

Gate
Post

Gate
Post

Gate
Post
WALL

Chainlink
Post

Chainlink
Post

KEY:

= Hinge Pin
= MUST measure 2-4”
= MUST measure 2-4”
Step 2: Measure/Secure Gate Bracket (#3)
With gate in closed posion, aach Fing Bar (#4) to Post Bracket (#2) using a Securing Pin (#5) in hole 2-D (shown below (le)).
Next, place a Securing Pin (#5) in the opposite end of the Fing Bar (#4) and secure to the Gate Bracket (#3).
Hold Gate Bracket (#3) to the gate and clamp into place.
The distance from the center of hole 2-D and the center of the Gate Bracket must measure 29 3/8”.
Clamp/secure brackets then remove Fing Bar (#4).
Note: If wall mounng, use Gate Bracket (#3) on the wall and the Post Bracket (#2) on the gate (shown below (right)).

Gate
Post
2A
2B
2C
2D
Gate



= 29 3/8”

Gate in CLOSED posion
WALL

Gate
Gate in CLOSED posion


2A
2B
2C
2D
= 29 3/8”
Important:
- This gate closer is mounted on the swing/open side of the gate and pushes the gate closed.
- A Gate Stop must be installed to keep gate from opening beyond 90 degrees.
- If using tension/spring hinges, release all tension and remove spring closers.
- Do NOT use with bulldog/strap style hinges. For best results, use male/female style hinges.






 
Post End --->
<--- Gate End
No. Part Name Qty.
2
1
3
4
5
Hydraulic Cylinder
Post Bracket (Triangular)
Gate Bracket
Fing Bar
Securing Pins (Hexagon Head)
Spacers
Cap Screws
Washers
6
7
8
1
1
1
1
2
4
2
2
Retaining Bar
9
1

Wall Mounng a TB Gate Closer
(may restrict 90 degree opening)