Instructions / Assembly

ManualsBrandsUnbranded ManualsHeating, Venting & Cooling5-Day 2-Stage Programmable Thermostat

This manual covers the following models:

• T705

INSTALLATION MANUAL

A trained, experienced technician

must install this product.

Carefully read these instructions. You

could damage this product or cause a

hazardous condition if you fail to follow

these instructions.

Need Help?

For assistance with this product please visit

http://www.pro1iaq.com or call Pro1

Customer Care toll-free at 888-Pro1iaq

(776-1427) during normal business hours

(Mon-Fri 9 AM - 6 PM Eastern)

Installation Tips

Thermostat Quick Reference

Subbase Installation

Wiring

Wiring Diagrams

Technician Setup

Technician Setup Menu

Mounting and Battery Installation

Programming The Thermostat

Programming The Thermostat (cont)

Specifications

Table of Contents

Thermostat Applications Guide

Page

Battery Power

Hardwire (Common Wire)

Hardwire (Common Wire) with Battery Backup

Power Type

noitpircseD

Gas or Oil Heat

Electric Furnace

Heat Pump (No Aux. or Emergency Heat)

Heat Pump (with Aux. or Emergency Heat)

Multi-stage Systems

Heat Only Systems

Heat Only Systems - Floor or Wall Furnaces

Cool Only Systems

Millivolt

Yes

Rev. 0850

Una versión española de este

manual puede ser descargada

en www.pro1iaq.com

® U.S. Registered Trademark. Patents pending.

Summary of content (12 pages)

PAGE 1
INSTALLATION MANUAL This manual covers the following models: • T705 Power Type Thermostat Applications Guide D e s c r i p ti o n Gas or Oil Heat Yes Electric Furnace Yes Heat Pump (No Aux. or Emergency Heat) Yes Heat Pump (with Aux.
PAGE 2
INSTALLATION TIPS Wall locations The thermostat should be installed approximately 4 to 5 feet above the floor. Select an area with average temperature and good air circulation.
PAGE 3
Getting to know your thermostat 1 2 1 LCD Days of the week and time 6 Hold is displayed when thermostat program is permanently overridden. Button options 7 3 4 8 5 2 Glow in the Dark Light Button 3 Fan Switch 4 System Switch 5 Easy Change Battery Door 6 Setpoint Buttons 7 User Buttons 8 Universal Private Label Badge Displays the user selectable setpoint temperature. Indicates the current room temperature.
PAGE 4
SUBBASE INSTALLATION Caution: Electrical Hazard Mercury Notice: All of Pro1’s products are mercury free. However, if the product you are replacing contains mercury, dispose of it properly. Your local waste management authority can give you instructions on recycling and proper disposal. Failure to disconnect the power before beginning to install this product can cause electrical shock or equipment damage. For vertical mount put one screw top and one screw bottom.
PAGE 5
WIRING Caution: Electrical Hazard Warning: Failure to disconnect the power before beginning to install this product can cause electrical shock or equipment damage. All components of the control system and the thermostat installation must conform to Class II circuits per the NEC Code. Wiring 1. If you are replacing a thermostat, make note of the terminal connections on the thermostat that is being replaced. In some cases the wiring connections will not be color coded.
PAGE 6
WIRING DIAGRAMS Power supply Factory-installed jumper. Remove only when installing on 2-transformer systems. Use either O or B terminals for changeover valve. Use a small piece of wire (not supplied) to connect W and Y terminals. Set fan operation switch to electric Optional 24 VAC common connection when thermostat is used in battery power mode.
PAGE 7
TECHNICIAN SETUP MENU Gas or Electric Setup Gas: For systems that control the fan during a call for heat, put the fan operation switch to the GAS position. Electric: The thermostat operation switch should be put in the ELEC position. This setting allows the thermostat to operate the fan when the fan relay is connected to the G terminal. Fahrenheit/Celsius Display Select F or C with the jumper pin Reset button Select F or C with the jumper pin on the back of the thermostat.
PAGE 8
TECHNICIAN SETUP MENU Technician Setup Menu This thermostat has a technician setup menu for easy installer configuration. To setup the thermostat for your particular application: 3. Configure the installer options as desired using the table below. Use the or keys to change settings and the NEXT STEP or PREV STEP key to move from one option to another. Note: Only press DONE key when you want to exit the Technician Setup options. 1. Press MENU button 2. Press and hold TECH SET button for 3 seconds.
PAGE 9
MOUNT THERMOSTAT & BATTERY INSTALLATION Mount Thermostat Align the 4 tabs on the subbase with corresponding slots on the back of the thermostat, then push gently until the thermostat snaps in place.
PAGE 10
PROGRAMMING THE THERMOSTAT Set Time Follow the steps below to set the day of the week and current time: 1. Press MENU 2. Press SET TIME 3. Day of the week will be flashing. Use the day of the week. or key to select the current 4. Press NEXT STEP 5. The current hour is flashing. Use the or key to select the current hour. When using 12-hour time, make sure the correct a.m. or p.m. choice is selected. 6. Press NEXT STEP 7. Minutes are now flashing. Use the or key to select current minutes. 8.
PAGE 11
PROGRAMMING THE THERMOSTAT You can use the table below to plan your customized program schedule. Programming Table Day of the Week Weekday Events Time Setpoint Temperature (Heat) Setpoint Temperature (Cool) Wake Leave Return Sleep Saturday Wake Leave Return Sleep Sunday Wake Leave Return Sleep Set Program Schedule To customize your program schedule, follow these steps Weekday: 1. Select HEAT or COOL from the system switch. Note: You have to program heat and cool each separately. 2. Press MENU 3.
PAGE 12
SPECIFICATIONS & CONTACT INFORMATION Specifications The display range of temperature The control range of temperature Load rating Display accuracy Swing (cycle rate or differential) Power source Operating ambient Operating humidity Dimensions of thermostat 41ºF to 95ºF (5ºC to 35ºC) 44ºF to 90ºF (7ºC to 32ºC) 1 amp per terminal, 1.5 amp maximum all terminals combined ± 1ºF Heating is adjustable from 0.4ºF to 2.0ºF Cooling is adjustable from 0.4ºF to 2.