SP5733 USER MANUAL Please carefully check the unit and make sure there is no damage when you open the carton. QUESTIONS, PROBLEMS, OR MISSING PARTS? Please Contact Customer Service Before Returning to Store www.soupro.com servicespi@sourceproinc.
General Information Table of Contents • GENERAL INFORMATION FCC/ICSES Information 2 Safety Instructions 2 Warranty 4 • ASSEMBLY INSTRUCTIONS Preparation 5 Assembly 7 • FIREPLACE OPERATIONS Operating Instructions 11 Care And Maintenance 12 Troubleshooting 13 FCC / ICES Information This equipment has been tested and found to comply with the limits for Class B digital devices, pursuant to part 15 of the FCC rules.
General Information • To prevent a possible fire, DO NOT block any air intakes or exhaust in any manner. DO NOT use on soft surfaces, like a bed, where opening may become blocked. • ALWAYS plug this unit directly into a wall outlet/receptacle. NEVER use with an extension cord or relocatable power tap (outlet/power strip). • This heater includes an automatic protection system that will shut off the unit to prevent overheating.
General Information Warranty 1-YEAR LIMITED WARRANTY Soupro Limited Inc. (hereinafter referred to collectively as “the Company”) warrants that your new KOMODO Electric Fireplace is free from manufacturing and materials defects for a period of one (1) year from date of purchase. Subject to the following conditions and limitations: 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12.
Preparation IMPORTANT INFORMATION ASSEMBLY INSTRUCTIONS 1. Before you begin, locate the instructions and hardware. Be sure you have all of the parts and can identify them. 2. To avoid scratching the finish, assemble the product on a soft, non-abrasive surface such as carpet or cardboard. 3. Assembly of this product may require more than one person. 4.
Preparation Parts List ASSEMBLY INSTRUCTIONS C D A B E A Front Glass x1 D Remote Control x1 B Fireplace x1 E Acrylic Shards x1 C Mounting Bracket x1 Hardware Identification Number of spare hardware is indicated in ( ).
Assembly - Wall Mount Installation 1. Remove mounting bracket (C) from back of fireplace (B) by unscrew two screws at the top of the unit. ASSEMBLY INSTRUCTIONS C C B 2. Choose a wall location to attach the mounting bracket (C). Position the mounting bracket (C) in the desired location. Use a level to align the bracket and mark the four holes with a pencil.
Assembly - Wall Mount Installation 3. Select the hardware appropriate for mounting bracket installation. STUD WALL • Secure the mounting bracket (C) to wall using screws (AA) at marked stud locations. ASSEMBLY INSTRUCTIONS DRYWALL • Drill holes at marked locations and secure the mounting bracket (C) to the wall with toggle bolts and washers (not included). CONCRETE WALL • Drill 5/16-inch holes at marked locations, then insert wall anchors (BB) into holes.
Assembly - Wall Mount Installation 5. Distribute the Acrylic Shards (E) evenly in the tray of the fireplace (B).
Assembly - Wall Mount Installation 6. Hang the front glass (A) on the hooks at both side of fireplace (B), lock the front glass (A) by closing the latches on both side as illustrated below.
Operating Instructions AM PM Power Button • Press the POWER button to turn ON or OFF the unit. • When the unit is in ON mode, touch control panel light will fully light up for 8 sec and then shut down if without any others operation including remote control. • When the unit is in OFF mode, the POWER symbol LED will Semi-bright. When power OFF, unit will be stopped, if heater is working before power OFF the unit, fan will have 20 seconds delay to ensure heat will not be trapped inside the unit.
Care And Maintenance CLEANING INFORMATION: • Make sure the unit is turned off, unplugged and the heating elements of heater are cool whenever you are cleaning the heater. • Clean the metal trim using a water-dampened, soft, and clean cloth. DO NOT use brass polish or household cleaners as these products will damage the metal trim. • The motors used on the fan and the flame generator assembly are pre-lubricated for extended bearing life and require no further lubrication.
Troubleshooting Possible Causes Solutions 1. No power, logs do not glow. 1. The unit does not have power. 1. Check that unit is plugged into a standard 120 volt outlet. Then make sure power is set at "ON" position. 2. "E1" is displayed on control panel. 2. The overheat protection device has been engaged. 2. Unplug unit, wait 5-10 minutes, then the sensor will reset itself. Plug the unit back in and turn on the heater. If the problem persists, call customer service. 3.
QUESTIONS, PROBLEMS, OR MISSING PARTS? Please Contact Customer Service Before Returning to Store www.soupro.com Ver.2 servicespi@sourceproinc.com +1-844-455-4621 Crafted in China Distributed by Soupro Limited Inc.
SP5733 MANUEL D'UTILISATEUR Vérifiez soigneusement l'appareil et assurez-vous qu'il n'y a pas de dommages lorsque vous ouvrez le carton. QUESTIONS, PROBLÈMES OU PIÈCES MANQUANTES? Contactez le service clientèle avant de le retourner au magasin www.soupro.com servicespi@sourceproinc.
Informations générales Table des matières • GENERAL INFORMATION Informations FCC / IC 16 Information de securite 16 Garantie 18 • INSTRUCTIONS D’ASSEMBLÉE Préparation 20 Assemblée 21 • OPÉRATIONS DE FOYER Instructions d’operation 25 Soins et entretien 26 Guide de depannage 27 Informations FCC / IC Cet article a été testé et déclaré conforme aux limites imposées aux dispositifs numériques de classe B, conformément à l’alinéa 15 du règlement de la FCC.
General Information • Afin de prevenir les risques d’incendie, ne bloquez JAMAIS les ouvertures de ventilation ou de sortie d’air de quelque facon que ce soit. Ne placez PAS l’appareil sur une surface molle, comme un lit, car l’ouverture pourrait se bloquer. • Ne placez PAS l’appareil directement sous une prise de courant. Branchez TOUJOURS l’article directement sur une prise murale. N’utilisez JAMAIS une rallonge ni une prise rechargeable (barre d’alimentation).
Informations générales GARANTIE 1 AN GARANTIE LIMITEE Soupro Limited Inc. (ci-apres refere comme la (compagnie) garantie que votre nouveau foyer electrique KOMODO est libre de tous defauts de fabrication pour une periode de un an de la date d’achat. Sujet aux conditions et limitations suivantes. 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. Le foyer electrique doit etre installe et utilise en accord avec le manuel d’installation et d’utilisation fournis avec l’appareil.
Préparation UNE INFORMATION IMPORTANT INSTRUCTIONS DE MONTAGE 1. Avant de commencer, localisez les instructions et le matériel. Assurez-vous d'avoir toutes les pièces et peut les identifier. 2. Pour éviter de gratter la finition, assemblez le produit sur une surface douce et non abrasive comme le tapis ou le carton. 3. L'assemblage de ce produit peut exiger plus d'une personne. 4.
Préparation Liste des pieces INSTRUCTIONS DE MONTAGE C B E D A A Couvercle avant x1 D Télécommande x1 B Foyer x1 E Pierres x1 C Support de Montage x1 Identification de la quincaillerie Nombre de materiel en () est separe pour la sauvegarde AA x 4+(1) 20 BB x 4+(1)
Assemblée - Installation Murale 1. Retirez le support de montage (C) a l'arriere du foyer (B) en devissant les deux vis en haut de l'unite. INSTRUCTIONS DE MONTAGE C C B 2. Choisissez un emplacement sur le mur pour fixer le support de montage (C). Positionner le support de montage (C) à l'endroit désiré. Utilisez un niveau pour aligner le support et marquer les quatre trous avec un crayon.
Assemblée - Installation Murale 3. Sélectionnez le matériel approprié pour le montage du support. MONTANT DE MUR • Fixer le support de montage (C) au mur en utilisant les vis (AA) à l'emplacement des poteaux marqués. INSTRUCTIONS DE MONTAGE CLOISON SÈCHE • Percez des trous aux endroits indiqués et fixer le support de montage (C) au mur avec des boulons à ailettes et des rondelles (non inclus).
Assemblée - Installation Murale 5. Distribuer les pierres (E) uniformément dans le plateau du foyer (B).
Assemblée - Installation Murale 6. Accrochez le verre avant (A) sur les crochets des deux côtés du foyer (B), verrouillez le verre avant (A) en fermant les loquets des deux côtés, comme illustré ci-dessous.
INSTRUCTIONS D’OPERATION AM PM Bouton d’Alimentation • Appuyer sur le bouton d'alimentation pour mettre l’appareil sous tension ou hors de l'appareil. • Lorsque l'appareil est en mode MARCHE, touchez le du panneau de commande va allumer la lumière pour 8 secondes et s’éteindra si aucune autre opération n’est fait incluant ceux sur la télécommande. • Lorsque l'appareil est en mode ARRET, le voyant d'alimentation DEL sera semi-brillant. Lorsque l'alimentation est a ARRET, l'unite s’arretera.
SOINS ET ENTRETIEN RENSEIGNEMENTS SUR LE NETTOYAGE : • Assurez-vous que l'appareil est éteint, débranché l’appareil, attendre que l’appareil soit froid avant de nettoyer. • Nettoyer la garniture métallique à l'aide d'un chiffon doux et propre imbibé d'eau. NE PAS utiliser de vernis pour laiton ou de nettoyants ménagers, car ces produits endommagerait la garniture métallique.
GUIDE DE DEPANNAGE PROBLÈME CAUSE POSSIBLE MESURE CORRECTIVE 1. L’appareil n’est pas alimenté; les bûches ne scintillent pas. 1. L’appareil n’est pas alimenté. 1. Assurez-vous que le cordon d’alimentation est branché convenablement sur une prise standard de 120 V. Assurez-vous ensuite que l’appareil est mis sous tension. 2. Le capteur de surchauffe est engage. 2. Débrancher l’unité, attendre 5 à 10 minutes, le capteur se réinitialisera par lui même. Rebrancher l’unité et mettre l’appareil en marche.
QUESTIONS, PROBLÈMES OU PIÈCES MANQUANTES? Contactez le service clientèle avant de le retourner au magasin www.soupro.com Ver.2 servicespi@sourceproinc.com +1-844-455-4621 Fabriqué en Chine Distribué par Soupro Limited Inc.