Installation Guide

ManualsBrandsUnbranded ManualsBathMuseo Single-Handle 1-Spray Shower Faucet with Volume Control in Polished Graphite (Valve Included)

Shower System S-5301

Installation Brief

1 2 3 4

Tools & Materials

 Need Help?

Contact Symmons customer service:

P: (800) 796-6667

gethelp@symmons.com

Mon - Fri 7:30 am - 7:00 pm EST



Please check Symmons website

for technical help, the latest product

information and warranty policy.

www.symmons.com/service

Museo™

Decorative Finish Code

append to part numbers if applicable

-STN

Satin Nickel

-BLK

Polished Graphite

Chrome (standard)

Model Number

S-5301

Shower System

1 2 3 4

Handle kit

T-665

COLD

supply inlet

HOT

supply inlet

Showerhead

532SH

Protective valve shield (not shown) T-176

Temp Limit

stop screw

Escutcheon

mounting plate

Note: Piping, ttings and tools are not included.

Actual plumbing should be determined and

installed by a licensed plumber.

Mounting

plate, T-177

Shower arm

532SA

Tools & Materials

Volume control handle

T-669

Temptrol

Control Valve

S-46-1-BODY

S-46-1X-BODY

Screwless escutcheon kit

T-668A-NS-K001

Dome cover

T-666

Visual Guide

Museo Shower System, S-5301

Summary of content (5 pages)

PAGE 1
Museo™ Shower System S-5301 Installation Brief Model Number  Tools & Materials S-5301 Shower System Need Help? Contact Symmons customer service: P: (800) 796-6667 gethelp@symmons.com Mon - Fri 7:30 am - 7:00 pm EST Decorative Finish Code append to part numbers if applicable check Symmons website  Please for technical help, the latest product -STN Satin Nickel -BLK Polished Graphite -- Chrome (standard) 1 2 3 information and warranty policy. www.symmons.
PAGE 2
Installation Instructions Rough-in Installation Control valve assembly, piping and fittings (Note: Illustrations below show valve model without stops) Reference as required: Page Visual guide.....................................1 Dimensions illustration.................3 1) Determine wall thickness ■■ Determine type of wall and wall thickness where valve will be mounted. ■■ Consider whether to use mounting plate by reviewing figure 2 below. ■■ Skip ahead to Step 3 if mounting plate is not used.
PAGE 3
7) Flush system, check for leaks ■■ Turn valve to the warm position and run for a few minutes. ■■ If system is dirty, remove valve spindle in center of valve to ensure proper flushing. (See service instructions.) ■■ Check for leaks around valve assembly and all pipe fittings. 8) Set Temp Limit stop screw Reference page 2, figure 3 The temperature limit stop screw limits valve handle from being turned to maximum position resulting in excessive hot water discharge temperatures.
PAGE 4
Parts Assembly Temptrol Shower Control Valve, S-46-1-BODY hot seat cold seat Seat repair kit (TA-4) Hot seat removal tool (T-35A) Shower supply Temptrol Control Valve Cold seat removal tool (T-35B) “C” cold supply Hot seat “H” hot supply Tub supply plug 5/16" wood screw Volume spindle (TA-25A) Cold seat 5/16" Allen wrench Spindle cap assy.
PAGE 5
Trouble Shooting Chart Problem Cause Solution Valve will not pass water. Both hot and cold water supplies are not turned on. Turn on both supplies. Valve will not operate unless both hot and cold water pressure is on. Valve leaks when shut off. Hot and cold washers are worn or foreign matter (dirt, chips) is lodged between washers and seat surfaces. 1) Replace washers using control spindle washer repair kit, p/n TA-9.