Quick Installation Guide RTH8500 Series Touchscreen Programmable Thermostat 69-2219EF-03
Installation is Easy Label wires and remove your old thermostat Install and wire your new thermostat Set your new thermostat to match your heating/cooling system – This thermostat works with virtually all System Types – It is preset for the most common system We are here to help. Call 1-800-468-1502 for wiring assistance before returning the thermostat to the store.
1 Turn Off Power to Heating/ Cooling System M28097 1 69-2219EF—03
2 Remove Old Thermostat Remove old thermostat but leave wallplate with wires attached. Is there a sealed tube containing mercury? If so, see back cover for proper disposal instructions.
3 Label Wires with Tags Label the wires using the supplied wire labels as you disconnect them.
Separate Wallplate from New Thermostat 4 Remove wallplate from the new thermostat and mount onto wall.
5 Mount Wallplate Mount the new wallplate using the included screws and anchors. M27514 Drill 3/16-in. holes for drywall Drill 3/32-in.
6 Connect Wires Simply match wire labels. SCREW INSERT WIRES THEN TIGHTEN SCREWS CONVENTIONAL LABELED WIRES CONVENTIONAL WIRE HOLE Y2 Y W R RC W Y G W2 R G C M27515 Remove metal jumper if you have both R and Rc wires. Labels don’t match? See page 21. Have a Heat Pump system? See pages 22–23. We are here to help. Call 1-800-468-1502 for wiring assistance.
7 Install Batteries Install three AAA alkaline batteries and remove tab. M28335 Back of thermostat Remove tab.
8 Install Thermostat onto Wallplate Install thermostat onto the wallplate on the wall.
9 Turn Power Back On Turn the power back on to the heating/cooling system.
10 Set Time and Date Press s/t to set date TUE 15 Press s/t to set month Press s/t to set year 6 2006 DONE M28338 Press DONE to save changes Press s/t to set time TUE 6 1:00 PM DONE M28339 Press DONE to save and exit 69-2219EF—03 10
11 If your system type is... If your system type is: q Single Stage Heat and Cool Congratulations, you’re done! If your system type is: q Multistage Heat and Cool q Heat Pump* without Backup Heat q Heat Pump* with Backup Heat q Heat Only q Cool Only Continue with advanced installation on next page to match your thermostat to your system type. *Heat Pump—an air conditioner that provides cooling in the summer, and also runs in reverse in the winter to provide heating.
Advanced Installation System setup....................................................................................... 13 Wiring.................................................................................................. 21 Troubleshooting................................................................................... 24 Customer assistance........................................................................... 26 Limited warranty...............................................................
RTH8500 About your System setup new thermostat 1. Press SYSTEM. TUE 70 Inside 70 Following Schedule SYSTEM HEAT Set To SETUP FAN AUTO Outside SCHED HOLD 43 SCREEN MORE WIRING 6:01 AM M28340 TUE ASSISTANCE 2. FAN Press and hold blank center key until the Inside Set To screen changes (approximately 5 seconds).
Advanced Installation Guide TUEnew thermostat About yoursettings Changing See pages FAN 15–20 to change Function Settings. 70 Inside SETUP AUTO Function Set To 70 Setting 20 0120 WIRING DONE M28341 Press s/t to select function Press s/t to change setting TROUBLESHOOTING ASSISTANCE 3. Press DONE to exit & save changes. NOTE: Some functions in the following pages may not appear due to previous selections made.
RTH8500 About your System setup new thermostat NOTE: If you set the time and date as shown on page 10, press NEXT to function 0170 and go to page 16. SETUP See page 14 to navigate between functions. Settings & Options Press s/t to change the first two digits of the year: 0130 Year Setting (second two digits) Press s/t to change the last two digits of the year: 20 = Year 20xx 21 = Year 21xx WIRING Function 0120 Year Setting (first two digits) 01 - 99 (i.e.
Advanced Installation Guide About your System setup new thermostat See page 14 to navigate between functions. TROUBLESHOOTING ASSISTANCE WIRING SETUP Function Settings & Options 0170 Select System Press s/t to select your system Type type: 1 Heat/cool: Gas, oil or electric heating with central air conditioning. 2 Heat pump: Heat pump without backup or auxiliary heat. 3 Heat only: Gas, oil or electric heat without central air conditioning.
RTH8500 About your System setup new thermostat See page 14 to navigate between functions. 0190 Heat Pump Changeover Valve (for heat pumps only) Press s/t to select whether your changeover valve is used in heating or cooling: 0 Cooling changeover valve: Use this setting if you connected a wire labeled “O” to the O/B terminal (see page 22). 1 Heating changeover valve: Use this setting if you connected a wire labeled “B” to the O/B terminal (see page 23).
Advanced Installation Guide About your System setup new thermostat See page 14 to navigate between functions. 0270 Emergency Heat Cycle Rate (heat pumps only) TROUBLESHOOTING ASSISTANCE WIRING SETUP Function Settings & Options 0240 Heating Cycle Press s/t to select your heating Rate system: 5 Gas or oil furnace: Standard gas/oil furnace (less than 90% efficiency). 9 Electric furnace: Electric heating systems.
RTH8500 About your System setup new thermostat See page 14 to navigate between functions. Press s/t to select manual or automatic changeover: 0 Manual changeover (Heat/Cool/ Off). 1 Automatic changeover (Heat/ Cool/Auto/Off). Automatically turns on Heat or Cool based on room temperature. Note: System maintains minimum 3°F difference between heat and cool settings.
Advanced Installation Guide About your System setup new thermostat See page 14 to navigate between functions.
RTH8500 About your new thermostat Wiring—conventional system Alternate wiring (conventional systems) Remove metal jumper connecting R and Rc only if you must connect both R and Rc wires. If your old thermostat had only 1 C or C1 wire, connect it to the C terminal. If your old thermostat had 2 C or C1 wires, wrap each separately with electrical tape and do not connect them.
Advanced Installation Guide About your new Wiring—heat pump thermostat SETUP Connect wires: Heat Pump 1. Match each labeled wire with same letter on new thermostat. 2. Use a screwdriver to loosen screws, insert wires into hole, then tighten screws. WIRING 3. If E and Aux do not each have a wire connected, use a small piece of wire to connect them to each other. 4. Push any excess wire back into the wall opening. Labels don’t match? ASSISTANCE If labels do not match letters on thermostat, see page 23.
RTH8500 Wiring—heat pump SETUP WIRING ASSISTANCE Alternate wiring (for heat pumps only) Leave metal jumper in place, connecting R & Rc terminals. If your old thermostat had both V and VR wires, stop now and contact a qualified contractor for help. If your old thermostat had separate O and B wires, attach the B wire to the C terminal. If another wire is attached to the C terminal, stop now and contact a qualified contractor for help.
Advanced Installation Guide WIRING SETUP Troubleshooting If you have difficulty with your thermostat, please try the following suggestions. Most problems can be corrected quickly and easily. Display is blank • Make sure fresh AAA alkaline batteries are properly installed (see page 7). Cannot change system setting to Cool • Check Function 0170: System Type to make sure it is set to match your heating and cooling equipment (see page 16).
RTH8500 Troubleshooting • • • Check Function 0170: System Type to make sure it is set to match your heating and cooling equipment (see page 16). 25 69-2219EF—03 TROUBLESHOOTING Heating • system is running in cool mode ASSISTANCE Red light is on • If thermostat is in Emergency Heat mode the red light is normal. It shows that the thermostat is in emergency heat mode. • If thermostat is not in Emergency Heat mode, contact a qualified service contractor for repair.
Advanced Installation Guide For assistance with this product, please visit http://DIYthermostats.honeywell.com or call Honeywell Customer Care toll-free at 1-800-468-1502.
1-year limited warranty Honeywell warrants this product, excluding battery, to be free from defects in the workmanship or materials, under normal use and service, for a period of one (1) year from the date of purchase by the consumer. If at any time during the warranty period the product is determined to be defective or malfunctions, Honeywell shall repair or replace it (at Honeywell’s option).
This thermostat contains a Lithium battery which may contain Perchlorate material. Perchlorate Material—special handling may apply, See www.dtsc.ca.gov/hazardouswaste/perchlorate MERCURY NOTICE: Do not place your old thermostat in the trash if it contains mercury in a sealed tube. Contact your local waste management authority for instructions regarding recycling and proper disposal. CAUTION: To avoid possible compressor damage, do not run air conditioner if the outside temperature drops below 50°F (10°C).
Guide d’installation rapide Série RTH8500 Thermostat programmable à écran tactile
L’installation est facile ! Étiquetage des fils et retrait de l’ancien thermostat Installation et raccordement du nouveau thermostat Configuration du nouveau thermostat pour correspondre à votre système de chauffage/ climatisation – Ce thermostat fonctionne avec pratiquement tous les types de systèmes – Il est préréglé en prévision des systèmes les plus communs Noussommesàvotreservice. Composer le 1-800-468-1502 pour obtenir de l’aide au raccordement avant de retourner le thermostat au magasin.
1 Couper le courant du système de chauffage/de climatisation M28097 1 69-2219EF—03
2 Retirer l’ancien thermostat Retirer l’ancien thermostat, mais laisser en place la plaque murale et les fils sans les détacher. Laisser la plaque de montage en place Y a-t-il une ampoule contenant du mercure? Si c’est le cas, se reporter aux consignes figurant sur la couverture avant de ce livret pour connaître les règlements concernant l’élimination.
3 Étiqueter les fils Étiqueter les fils à l’aide des étiquettes fournies à mesure que les fils sont débranchés.
Séparer la plaque murale du nouveau thermostat 4 Retirer la plaque murale du nouveau thermostat et l’installer au mur.
5 Installer la plaque Installer la nouvelle plaque murale à l’aide des vis et des chevilles d’ancrage fournies.
6 Raccorder les fils Il suffit ensuite de faire correspondre les fils avec les étiquettes. VIS INSÉRER LES FILS, PUIS SERRER LES VIS CLASSIQUE FILS ÉTIQUETÉS OUVERTURE POUR LES FILS CLASSIQUE Y2 Y W R RC W Y G W2 R G C MF27515 Retirer le cavalier en métal s’il y a à la fois les fils « R » et « Rc ». Les étiquettes ne correspondent pas? Voir page 21. Avez-vous une thermopompe? Voir pages 22–23. Nous sommes à votre service.
7 Installer les piles Installer 3 piles alcalines AAA à l’arrière du thermostat et retirer l’onglet. Dos du thermostat M28335 Retirer l’onglet.
8 Fixer le thermostat à la plaque murale Installer le thermostat sur la plaque murale fixée au mur.
9 Rétablir l’alimentation électrique Rétablir l’alimentation électrique du système de chauffage-refroidissement.
10 Régler l’heure et date Appuyer sur s ou t pour régler la date. TUE 15 Appuyer sur s ou t pour régler le mois. Appuyer sur s ou t pour régler l’année 6 2006 DONE M28338 Appuyer sur DONE pour sauvegarder et quitter. Appuyer sur s ou t pour régler l’heure puis appuyer sur DONE pour sauvegarder et quitter.
11 Si votre système est du type suivant... Si votre système est du type suivant : q Chauffage et refroidissement à un étage Félicitations, vous avez terminé! Si votre système est du type suivant : q Chauffage et refroidissement, multiétages q Thermopompe* sans chauffage d’appoint q Thermopompe* avec chauffage d’appoint q Chauffage seulement q Refroidissement seulement Passer au mode d’installation avancé à la page suivante pour faire correspondre le thermostat à votre type de système.
Guide d’installation avancé Modification des réglages................................................................... 13 Câblage................................................................................................ 21 Dépannage.......................................................................................... 24 Assistance à la clientèle...................................................................... 26 Garantie limitée...............................................................
RTH8500 About your new Modification desthermostat réglages 1. Appuyer sur SYSTEM. RÉGLAGE TUE FAN 70 Inside AUTO Set To Following Schedule SYSTEM Outside 6:01 SCHED 43 AM HOLD SCREEN WIRING HEAT 70 MORE M28340 70 70 ASSISTANCE TUE 2. Appuyer sur la touche du centre blanche et continuer à le faire jusqu’à ce que l’affichage FAN Inside Set To change AUTO (environ 5 secondes).
Guide d’installation avancé TUE des réglages Modification RÉGLAGE Voir les pages 15–20 pour modifier le réglage des FAN Inside Set To fonctions. AUTO Fonction 70 70 Paramètre 20 0120 WIRING DONE M28341 Appuyer sur s t pour sélectionner la fonction. Appuyer sur s t pour modifier les paramètres. TROUBLESHOOTING ASSISTANCE 3. Appuyer sur DONE pour sauvegarder et quitter.
RTH8500 Modification des réglages Voir page 14 pour naviguer entre les différentes fonctions. Fonction Réglages et options 0130 ProgrammaAppuyer sur s/t pour modifier les tion de l’année deux derniers chiffres de l’année : (deux derniers 01 - 99 (c.-à-d. 2001 - 2099) chiffres) 01 - 12 (c.-à-d.
Guide d’installation avancé Modification des réglages Fonction Réglages et options 0170 Type de système Appuyer sur s/t pour choisir votre type de système : 1 Chauff./Clim. : Gaz, mazout ou chauffage électrique avec climatisation. 2 Thermopompe : 1 chauffage (pas de chauffage aux.). 3 Chauff. seulement : Gaz, mazout ou chauffage électrique sans climatisation. 4 Chauffage seulement avec ventilateur (gaz, mazout ou chauffage électrique). 5 Chauff.
RTH8500 Modification des réglages Voir page 14 pour naviguer entre les différentes fonctions. Réglages et options ASSISTANCE Appuyer sur s/t pour choisir si la vanne d’inversion est utilisée dans le chauffage ou la climatisation : 0 Vanne de climatisation : Utiliser ce réglage si le fil étiqueté «O» a été raccordé à la borne O/B (voir la page 22). 1 Vanne de chauffage : Utiliser ce réglage si le fil étiqueté «B» a été raccordé à la borne O/B (voir la page 23).
Guide d’installation avancé Modification des réglages RÉGLAGE Voir page 14 pour naviguer entre les différentes fonctions.
RTH8500 Modification des réglages Voir page 14 pour naviguer entre les différentes fonctions. Appuyer sur s/t pour choisir le format de la température : 0 Fahrenheit 1 Celsius 0330 Changement horaire été Appuyer sur s/t pour choisir une option : 0 OFF : L’horaire d’été est désactivé. 1 ON : Changement automatique à l’heure avancée (pour les zones qui n’utilisent pas le nouveau calendrier d’heure avancée de 2007).
Guide d’installation avancé Modification des réglages RÉGLAGE Voir page 14 pour naviguer entre les différentes fonctions.
RTH8500 Câblage—systèmes classiques Câblage alternatif (systèmes classiques) Enlever le cavalier en métal entre R et Rc seulement les fils R et Rc doivent être raccordés. Si l’ancien thermostat avait seulement un fil C ou C1, la relier à la borne de C. Si l’ancien thermostat avait 2 fils C ou C1, enrouler chacun des fils séparément avec du ruban isolant et ne pas les raccorder.
Guide d’installation avancé Câblage—thermopompe CÂBLAGE SETUP Raccorder les fils : Thermopompe 1. Faire correspondre chaque fil étiqueté à la même lettre sur le nouveau thermostat. 2. Desserrer les bornes à vis à l’aide d’un tournevis, insérer les fils et serrer les vis. 3. Si les bornes E et Aux ne sont raccordés à aucun un fil, utiliser un bout de fil pour les raccorder l’une à l’autre. 4. Repousser le fil en excès dans l’ouverture dans le mur.
RTH8500 Câblage—thermopompe SETUP CÂBLAGE ASSISTANCE Câblage alternatif (pour thermopompes seulement) Laisser le cavalier en place, en reliant les bornes R et Rc. Si l’ancien thermostat avait des fils V et VR, arrêter maintenant et communiquer avec un entrepreneur pour obtenir de l’aide. Si l’ancien thermostat les fils O et B, raccorder le fil B à la borne C. Si un autre fil est raccordé à la borne C, arrêter maintenant et communiquer avec un entrepreneur.
Guide d’installation avancé DÉPANNAGE ASSISTANCE WIRING SETUP Dépannage Si vous éprouvez des difficultés, nous vous proposons d’essayer les solutions suivantes. La plupart des problèmes peuvent être corrigés rapidement et facilement. Rien n’apparaît à l’écran • Vérifier si des piles alcalines AAA neuves sont correctement installées (voir page 7).
RTH8500 Dépannage 25 69-2219EF—03 DÉPANNAGE • Vérifier la Fonction 170 : Type de système pour s’assurer que le réglage correspond au système de chauffage ou de climatisation (voir page 16). ASSISTANCE Chauffage fonctionne en mode climatisation WIRING Le voyant rouge • Si le thermostat est en mode chauffage de secours le voyant est allumé rouge est normal. Il indique que le thermostat est en mode chauffage de secours.
Guide d’installation avancé TROUBLESHOOTING ASSISTANCE WIRING SETUP Assistance à la clientèle Pour obtenir de l’aide sur ce produit Honeywell, veuillez consulter le site http://DIYthermostats.honeywell.com ou vous adresser sans frais aux Services à la clientèle de Honeywell au 1 800 468-1502.
Garantie limitée de un an La responsabilité de Honeywell se limite à réparer ou à remplacer le produit conformément aux modalités susmentionnées. HONEYWELL N’EST EN AUCUN CAS RESPONSABLE DES PERTES OU DOMMAGES, Y COMPRIS LES DOMMAGES INDIRECTS OU ACCESSOIRES DÉCOULANT DIRECTEMENT OU INDIRECTEMENT D’UNE VIOLATION QUELCONQUE D’UNE GARANTIE, EXPRESSE OU TACITE, APPLICABLE AU PRÉSENT PRODUIT NI DE TOUTE AUTRE DÉFECTUOSITÉ DU PRÉSENT PRODUIT.
Ce thermostat contient une pile au lithium qui pourrait contenir du perchlorate. Matériau contenant du perchlorate — des consignes de manipulation spéciales pourraient s'appliquer, prière de consulter www.dtsc.ca.gov/hazardouswaste/perchlorate AVIS CONCERNANT LE MERCURE : Si le présent thermostat remplace un thermostat contenant du mercure dans une ampoule scellée, ne pas jeter l’ancien thermostat à la poubelle.