Safety data sheet

ManualsBrandsUnbranded Manuals3D PrintingFilament Renkforce PLA plastic 1.75 mm Black 1 kg

Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau

Item no.: 1093127

Material Safety Data Sheet

Page 1 of 7

1. Product & Company Identification

Product: PLA Filament, 1,75 mm, black

Manufacturer: Conrad Electronic SE

Address: Klaus-Conrad-Str. 1, D-92240 Hirschau

Telephone: +49 (0) 9604 / 40 - 8988

Date of issue: 25.03.2014

Chemical name: 3, 6-dimethyl-1, 4-dione; polymer

Chemical family: Polyester

Common names: Polyactide, plyactic acid, PLA

Chemical formula: (C

)

Chemical structure: Lacdide: Polyactide:

2. Hazards Identification

Material CAS# Hazard

L-Lactide 4511-42-6 none known

DL-Lactide 95-96-5 none known

Poly (DL-lactide) 51063-13-9 none known

Poly (L-lactide) 33135-50-1 none known

Instability: None

Incompatibility: Stable

Decomposition: Slow reaction in the presence of water.

Polymerization: Will not occur, already a polymer.

Combustion: Carbon monoxide and/or carbon dioxide may from during the compustion of this product.

Emergency Overview:

Caution! may cause eye/skin irritation. Burning produces obnoxious and toxic fumes. Avoid contact with skin and eyes. Avoid

formation of dust and aerosols.

Appearance: Colorful filament

Physical state: Solid

Odor: None

Summary of content (7 pages)

PAGE 1
Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau Item no.: 1093127 Material Safety Data Sheet 1. Product & Company Identification Product: PLA Filament, 1,75 mm, black Manufacturer: Conrad Electronic SE Address: Klaus-Conrad-Str. 1, D-92240 Hirschau Telephone: +49 (0) 9604 / 40 - 8988 Date of issue: 25.03.
PAGE 2
Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau Item no.: 1093127 Material Safety Data Sheet 3. Composition/Information on Ingredients Solubility in water: React very slowly with water to become soluble. Appearance: Solid filament. Polymer: Residual monomer: <0.5% Residual solvent <0.05% Residual catalyst <200ppm Heavy metal <10ppm Water content ≤0.5% 4. First Aid Measures Eye contact: Rinse immediately with plenty of water, also under the eyelids, for at least 15 minutes.
PAGE 3
Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau Item no.: 1093127 Material Safety Data Sheet 5. Firefighting Measures Unusual Explosion Hazard and Fire: The material will burn if exposed to sufficient heat and an ignition source. Avoid dispersion of dust in the air to reduce dust explosion hazard potential. Extinguished Media: Water, Carbon dioxide, Dry chemical power, Foam.
PAGE 4
Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau Item no.: 1093127 Material Safety Data Sheet 6. Handling and Storage Safe handling advice: Avoid contact with skin and eyes. Avoid dust formation. Workers should be protected from the possibility of contact with molten material during fabrication. Low hazard for usual industrial or commercial handling. Use personal protective equipment. See Section 7. Storage: Store in cool place. Keep at temperatures below 122F (50 °C).
PAGE 5
Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau Item no.: 1093127 Material Safety Data Sheet 8. Physical and Chemical Properties Appearance: Colorful filament Physical state: Solid Odor: None Odor threshold: No data available pH: Not applicable Vapor pressure: Not determined Vapor density: Not determined Evaporation rate: No data available Density: 1.
PAGE 6
Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau Item no.: 1093127 Material Safety Data Sheet 10. Toxicological Information Principle Routes of Exposure: Eye contact. Skin contact. Inhalation. Ingestion. Acute toxicity: There were no target organ effects noted following ingestion or dermal exposure in animal studies. Local effects: May cause eye/skin irritation. Product dust may be irritating to eyes, skinand respiratory system.
PAGE 7
Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau Item no.: 1093127 Material Safety Data Sheet 12. Disposal Considerations Waste from residues / unused products: In accordance with local and national regulations. Do not contaminate ponds, waterways or ditches with chemical or used container. Contact manufacturer. Contaminated packaging: Empty remaining contents. Do not re-use empty containers.