u 5201 For pools round Flat bottom floor cleaner m 5211 For pools round Flat bottom or sloped bottom floor cleaner m 5310 For pools up to 18ft x 33ft or 28 ft round Flat bottom or sloped bottom floor cleaner
1! Warning and Safety 1! Follow instructions bellow and review your local pool safety regulations « Keep the power supply away from pool edge by at least 6 ft Ensure your electrical outlets are properly grounded and have a Ground Fault Current Interrupter (GUCCI) protected.
Gatling Started A. Wheel assembly: 5201 & 5310: Wheels are per-assembled 5211: + Place the wheel onto the body. + Drop the wheel axle pin to the hole at the middle of the wheel « Push the axle pin in until you hear a click B. Cord Floaters. Cord floater is a foam tube which is split along the tube length. It helps the cord stay on top of water surface and therefore minimize chance of cord tangling. a. Untie the Velcro strap b. Spread out the foam tube and insert the cord into it. c.
. Side suction: a. b. 0. Swivel connection: 5310 only = 5201: Not included. 5211 & 5310: It can extend the suction beyond pool cleaner body width. Dirt vacuum can be done much faster. However, DO NOT use these side suction flaps if you have uneven pool bottom or pool liners with pleats i. Turn the pool cleaner upside down with the bottom facing up. ii. Place the side suction flap onto the suction channel as shown. iii. Tighten up the screw. The square swivel has 2 connector ends.
E. Prows supply: a. 5201: Do not plug it to wall outlet until the pool cleaner robot is placed inside a swimming pool and fully immersed. i. When it is ready to clean, plugging wall outlet and the machine will run for 90 minutes and then stop automatically. ii. Unplug, wait 30 seconds and then plug in again to run another 90 minutes cleaning cycle. b. 5211 and 5310: Check and make sure the power supply is set to the OFF position before you connect it to anything. i.
F. Pool cleaner placement a. Place just enough length of cord in the pool to reach the power supply. This is the optimum length of cord needed to clean your pool. Additional cord will lower the performance of the cleaner or even cause cord tangling. b. Turn on the power supply when it is ready to clean. Press down the toggle switch towards ON and the blue LED light turns on. The pool cleaner will run one cleaning cycle and then shut down automatically. ¢. Cleaning cycle: i. 6211: 2 hours ii.
Adjusting Direction and Spread Control 1. Direction adjust: To adjust the direction of the robot, rotate the outlet cover. Note that the direction the robot turns is the opposite of the where the indicator points. 2. Flap settings: a. Round shaped pools, it is recommended that the flaps at both ends do not share the same direction. For best performance have flap at the hinge end of the cleaner be straight and then the flap at the front of the cleaner rotated. b.
3. Speed control: This pool cleaner works the best at medium speed in normal circumstances. If your pool has a lot of fine debris, it is better to slow down the speed which allow enough time for the pool cleaner to pick up fine dirt. Similar principle as you vacuum your own carpet at home. Flap should set at partially opened. On the other hand you need a bigger push if the filter bag is dirty and therefore flap should set at fully opened. Adjust the speed that best fits your need o 4.
Cleaning the Filter Bag 1. Open up the pool cleaner: a) 5201 and 5211: Press in the button at the front of the cleaner and lift up the top shell. Continue to lift up the shell until you hear a “click” and the shell stays in place. b) 5310: Pull the tab at the front of cleaner and lift up top shell Lift up filter basket from the front until you hear a click. Open up the debris basket. Dump out the debris inside the basket. Use a hose to spray water and clean the basket and filter screen.
Troubleshooting « No/not enough power is going to robot « An object is blocking robot's rollers or impeller Symptom Possible reason(s) | Solution(s) Robot is not moving | « Electrical outlet/ « Check if electrical socket you are using is /Pump is not Clog tripped working by plugging in another know working operating » Plug is not electrical appliance into the socket and check to connected see if the GUCCI triggered. Reset it if needed. properly to outlet * Unplug the power supply for 30 seconds.
indicator light and Diagnostics Indicator light Diagnostic A When the power supply is plugged in to wall outlet and toggle switch is pressed towards ON, this blue LED should stay on indicating power supply functions normally. Otherwise check if the wall outlet has power or replace the power supply. This blue LED will light up when floating cord between power supply and the NO-TWIST swivel is connected properly. Otherwise please check the connections or replace the floating cord.
9 52 vehemence stem interdepartmental Part description 1 51333 Curved handle set. L & R. Grass green 51242 Outpatient flap assembly. Grass green 51070 Competitor Top shell. Black color Side wheels, Grey. PCs as a set 51342 Quick drain flap. Black 51050 Roller tubes. apes as a set 51412 Side suction flap. apes set. Black Debris basket Power supply.
5310 replacement parks Item | interdepartmental | Part description 1 51431 Pump outlet flap assembly. Grass green 2 51400 Pym motor 3 51441 Pump enclosure 4 51451 Top shell, Black color & 51461 Boston chassis 6 51171 side wheels, Grey. PCs asa set T BT Quick drain flap. Black 8 51480 Roller tubes, apes as.a set g 51412 Side suction flap.
ONE YEAR LIMITED WARRANTY This robot is warranted to be free from defects in materials and workmanship, under normal use and non-commercial application, for a period of ONE year. To obtain service, contact restroom at 408-823-1170 or email at Proof of purchase is required. This limited warranty is extended exclusively to the original purchaser and is non-transferable. The robot is intended for residential pool use and any commercial application voids all warranties.