PART LIST Top Panel Left Panel Right Panel Bottom Panel Left Partition Panel 1PC 1PC 1PC 1PC 1PC Right Partition Front Rail Front Middle Rail| Back Panel Small Drawer Panel Front Panel 1PC PCS PCS 1PC PCS Small Drawer Small Drawer Small Drawer Large Drawer Large Drawer Left Panel Right Panel Back Panel Front Panel Left Panel PCS PCS PCS PCS PCS Large Drawer Large Drawer | Drawer Bottom Left Door Panel | Right Door Panel Right Panel Back Panel Panel PCS PCS PCS 1PC 1PC Left Adjustable Right Adjustable | Supp
HARDWARE LIST 28*30mm @6*30mm Large Wood Small Wood Magnet Round Head Screw Knob Dowel Dowel 32 PCS (Extra 1) | 20 PCS (Extra 1) PCS 4 PCS (Extra 1) PCS | *D11mm Round Head Bolt Barrel Nut Long Bolt Short Bolt Bolt 7 PCS (Extra 1) 8 PCS 12 PCS (Extra 1) 4 PCS (Extra 1) | 12 PCS (Extra Spring Washer Flat Washer Shelf Holder Allen Wrench PCS (Extra) | 8 PCS (Extra 1) 8 PCS 1PC ADDITIONAL TOOLS (Not Provided) Note: It is not recommended to use power tools during assembly.
Please do not use tools to assemble this unit unless specifically indicated. Reference the images above any time the instructions state "lock the hardware". Note: Be sure fo check all hardware is locked when completed. Step 1. Attach knobs (part #5) to door panels (parts S & T) and drawer front panels (parts J & N) using round head bolts (part #6) and fillips head screwdriver.
Step 2. Attach magnets (part #3) to partition panels (parts E & F) using round head screws (part #4) and fillips head screwdriver. Step 3. Attach small drawer panels (parts small drawer back panel (part M) using small wood dowels (part #2) and lock the hardware. Slide drawer bottom panel (part R) into grooves of assembled unit {parts Attach small drawer front panel {part J) to assembled unit (parts using small wood dowels (part #2) and lock the hardware. Repeat for remaining drawers.
Step 4. Attach large drawer panels (parts large drawer back panel (part Q) using small wood dowels (part #2) and lock the hardware. Slide drawer bottom panel (part R) into grooves of assembled unit (parts Attach large drawer front panel (part N) to assembled unit (parts using small wood dowels (part #2) and lock the hardware. Repeat for remaining drawer. #2 2 x8 Step 5.
Step 6. Attach front rail (part G) to left panel (part B) using large wood dowels (part #1). Attach left partition panel (part E) to front rail (part G) and bottom panel (part D) using large wood dowels (part #1), barrel nuts (part #7), long bolts (part #8) and Allen wrench (part #14). Step 7. Attach front middle rails (part H) to left partition panel (part E) using large wood dowels (part #1).
Step 8. Attach front rail (part G) to right partition panel (part F) using large wood dowels (part #1). Attach right panel (part C) to front rail (part G) and bottom panel! (part D) using large wood dowels (part #1), barrel nuts (part #7), long bolts (part #8) and Allen wrench (part #14). Step 9. Carefully tum unit upright. Attach back panel (part 1) to assembled unit (parts using short bolts {part #9) and Allen wrench (part #14).
Step 10. Attach towel bars (part X) to left panel {part B) and right pane! {part C} using bolts (part #10} and Allen wrench (part #14). Attach support panels (part W) to back panel (part I) using large wood dowels (part #1), long bolts (part #8) and Allen wrench (part #14). Step 11. Attach top panel (part A) to assembled unit {parts using large wood dowels (part #1), flat washers (part #12), spring washers (part #11), bolts (part #10) and Allen wrench (part #14).
Step 14. Attach door panels (parts placing bottom pin hinges (per-installed in door) in the per-drilled holes of bottom panel (part D). Then depress the top spring-loaded pin hinge so it can be placed in the per-drilled holes of front rails (part G). Note: Be sure top and bottom pin hinges are fully extended to secure doors in place.