ATV CULTIVATOR OWNER’S MANUAL WARNING: Read carefully and understand all ASSEMBLY AND OPERATION INSTRUCTIONS before operating. Failure to follow the safety rules and other basic safety precautions may result in serious personal injury.
Thank you very much for choosing this product! For future reference, please complete the owner’s record below: Model: ____ATV-470_________ Purchase Date: _______________________ Save the receipt, warranty and these instructions. It is important that you read the entire manual to become familiar with this product before you begin using it. This machine is designed for certain applications only. The manufacturer cannot be responsible for issues arising from modification.
WORK AREA z Keep work area clean, free of clutter and well lit. Cluttered and dark work areas can cause accidents. z Keep children and bystanders away while operating the cultivator. Distractions can cause you to lose control, so visitors should remain at a safe distance from the work area.
ASSEMBLY Step 1: Assemble the Tire to the Wheel Carrier using the Wheel Shaft, Short Spacers, Flat Washers Ø20 and Cotter Pins Ø4x30 as shown in Picture 1. Assemble the other tire in the same way.
Step 2: Attach the Hitch Bracket to the Tongue using the Hex Bolt M12x65 and Nylon Lock Nut M12. Fix the Hitch Bracket using the Hex Bolts M8x60 and Nylon Lock Nuts M8.
Step 3: Attach the Base to The Frame using the Hex Bolts M10x55, Spring Washer Ø10, Big Washer Ø10 and Nylon Lock Nut M10. Attach the Connect Bar to the Joint on Axle using the Hex Bolt M10x35 and Nylon Lock Nut M10. Install the Hex Bolts M16x90 and Hex Nuts M16 to the Frame as shown in Picture 3.
Step 4: Attach the Handle to the Base using the Socket Head Screw M12x45 and Nylon Lock Nut M12. Note: Do not over tighten Socket Head Screw M12x45 and Nylon Lock Nut M12, the Handle should rotate freely. Step 5: Connect the Handle and the Connect Bar together using Hex Bolt M10x30 and Nylon Lock Nut M10.
Step 6: Pull the Handle into the middle of Base and lock it by the Lock Pin. Step 7: Install the Wheel Assembly to the Axle using Hex Bolt M10x30 and Hex Nut M10. Repeat above procedure for the other side.
Step 8: Install the Tongue Assembly to the Frame using Hex Bolts M10x75, Spring Washers Ø10 and Nylon Lock Nuts M10. Step 9: Put the Shank to the Frame as shown in Picture 9-2.
Step 10: Put the Shank Mounting Bracket on the tube of the Frame and insert the Shank into the square hole on the Shank Mounting Bracket. Fix the Shank Mounting Bracket and the Shank onto the Frame using Hex Bolt M12x85, Spring Washer Ø12 and Nylon Lock Nut M12. Install the rest 6 shanks in the same way. Adjust the position of the shanks if necessary.
Exploded Diagram 11
PARTS LIST PART # 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 DESCRIPTION Hitch Bracket Nylon Lock Nut M12 Nylon Lock Nut M8 Tongue Hex Bolt M12×65 Hex Bolt M8×60 Nylon Lock Nut M10 Frame Hex Bolt M10×75 Hex Nut M16 Hex Bolt M16×90 Locating Ring Hex Bolt M8×25 Oil Cup M6 Axle Holder Hex Bolt M10×35 Connect Bar Hex Bolt M10×30 Socket Head Screw M12×45 Handle Handle Grip QTY PART# 1 22 10 23 2 24 1 25 1 26 2 27 19 28 1 29 8 30 2 31 2 32 2 33 2 34 2 35 2 36 1 37 1 38 3 39 1 40 1 41 1 42 43 DESCRIP
MAINTENANCE • Maintain your cultivator. It is recommended that the general condition of any the cultivator be examined before it is used. Keep your cultivator in good repair by adopting a program of conscientious repair and maintenance. If any abnormal vibrations or noise occurs, have the problem corrected before further use. Have necessary repairs made by qualified service personnel.
