Instructions / Assembly

ManualsBrandsUnbranded ManualsBoxes & BracketsSlater Brass 2-Gang Floor Box with Tamper-Resistant Outlet and Cat5e Connectors

1. WARNING: TEST THAT POWER IS OFF AT CIRCUIT BREAKER OR

FUSE BLOCK!

2. Determine approximate location (which joists to put it between) and

route cable(s) to joist cavity and fasten cable within 12" of proposed

opening per NEC 334.30 leaving large enough loop to later install box

after finishing floor installation.

3. Determine box location and

drill four 3/4" diameter holes

using template “A” for FB1

series or template “B” for

FB2 series.

Note: When installing tile,

marble or hardwood flooring,

you may want to wait to cut

the opening during the fin-

ished floor installation to

ensure the opening in the

floor does not end up in the

middle of a tile or hardwood

plank.

4. Cut remainder of opening

using the appropriate tem -

plate by connecting the

edges of the holes.

5. Complete the finished floor

installation up to the previ -

ously cut opening, ensuring

the box will still fit into

opening.

6. Pull the wires through the

opening in floor and into the

auto-clamp feature. Knock-

outs are provided for low volt-

age cables if desired. If

Romex-type NM cable is

routed through the knockouts,

an approved wire clamp must

be used.

7. Attach box to flooring using

either the four #6 drywall

screws included or use the

assembled swing brackets.

Tighten screws firmly. When

assembling to carpet, the car-

pet may need to be trimmed

back to ensure the box flange

sets flush. Trim only the car-

pet loops/shag and leave the

carpet backing under the

flange for security. Cut the

padding back 1-2" larger than

the opening to ensure the

device seats firmly and flush

to the floor.

8. Install device(s) per appropriate

installation instructions below.

FB-1 & FB-2 SERIES

TAMPER-RESISTANT FLOOR BOX

INSTALLATION INSTRUCTIONS

NOTICE: READ BEFORE INSTALLING DEVICE

NEW/OLD CONSTRUCTION

FEATURES AND BENEFITS

NOTICE: For installation only by a electrician or other qualified

person in accordance with the National Electrical Code, Canadian

Electrical Code, local Codes and the instructions on this sheet.

CAUTION: RISK OF ELECTRICAL SHOCK. Turn off all power to

circuit before installing this device. Improper wiring of any electrical

device can cause serious injury or death.

CAUTION: Connect only copper or copper-clad wire to the device in

this package. Do not connect aluminum wire to this device.

NOTE: USE ONLY ELECTRICAL MOUNTING BOX PROVIDED.

P/N 340907

P.O. Box 4822, Syracuse, NY 13221-4822 • www.passandseymour.com • (800-223-4185) Printed in USA

• All FB*TR floor boxes include P&S 15A 125V Tamper-Resistant

Receptacles

• Meets NEC Section 406.11 requiring tamper-resistant receptacles

in dwellings.

• Complete line of low voltage connectors available thru P&S

• Installs before or after the floor is completed to ensure the best

possible finish

• Easy rectangular floor cut out

• Swing bracket mounting option, superior for tile or marble floors

• No messy caulking needed to meet scrub water requirements

• Plastic Boxes do not require ground bonding in most applications

INSTALLATION INSTRUCTIONS

This device should be installed in accordance with all appropriate codes

and standards. Warning: Turn off power to outlet box, using breaker or

fuse at service entrance. Verify that power has been removed by testing

with a circuit tester at the outlet box. Caution: This device is for use with

copper or copper-clad wire only.

A. After removing power as described above, use strip gauge on back of

outlet to strip all wires to desired length.

B. Attach wires according to the following diagram. Be sure the wires are

fastened securely either by the terminal screws or through the

speed-wire holes in the back of the outlet. Loosely fastened wires may

result in outlet failure and/or fire hazard. Attach wires using terminal

screws or speed-wire holes: Not both!

C. If using terminal screws: Terminal screws accept up to #12 AWG

wire. Loop wires around screws in a counterclockwise fashion. Fasten

terminal screws securely.

D. If using speed-wire holes: Fully insert #14 AWG solid copper wire

only into the speed-wire holes. Do not use speed-wire holes for cir-

cuits greater than 15 amps. If outlet must be removed, insert screw-

driver blade in the release slot and push it toward the front of the out-

let, releasing the wire. Discard the outlet.

E. Use feed through wires only when wiring to another outlet down stream.

F. Mount the outlet to the box by sandwiching the device to the box with the

intermediate sub-plate using provided #6-32 x 3/4" pan head mounting

screws. Note: Orient the Sub-plate to say “THIS SIDE UP”.

G. Place gasket over the box flange.

H. Assemble o-rings to the provided #6-32 x 1" oval head screws and

use these to assemble the cover plate to the box. Torque to

approximately 10 in/lbs ensuring the gasket stays in place under

the cover plate.

This device should be installed in accordance with all appropriate codes

and standards. Warning: Turn off power to outlet box, using breaker or

fuse at service entrance. Verify that power has been removed by testing

with a circuit tester at the outlet box. Caution: This device is for use with

copper or copper-clad wire only.

A. After removing power as described above, use strip gauge on back of

outlet to strip all wires to desired length.

B. Attach wires according to the diagram below. Be sure the wires are

fastened securely by the terminal screws.

Loosely fastened wires may result in outlet failure and/or fire hazard.

Terminal screws accept up to #12 AWG wire. Loop wires around

screws in a counterclockwise fashion. Fasten terminal screws securely.

C. Mount the outlet in box by

screw ing the strap directly

to the box using provided

#6-32 x 3/4" pan head

mounting screws.

D. Place the shell over the

single receptacle.

E. Place gasket over the box

flange.

F. Assemble o-rings to the

provided #6-32 x 1" oval

head screws and use these

to assemble the cover

plate to the box. Torque to

10 in/lbs ensuring the gas-

ket stays in place under

the cover plate.

TAMPER-RESISTANT DUPLEX RECEPTACLE(S)

TAMPER-RESISTANT SINGLE RECEPTACLE

DATACOM KEYSTONE TWO & FOUR PORT

KEYSTONE JACKS

A. See the instructions enclosed with the product for specific wiring.

B. Mount the device in box by sand wiching the device to the box with the

intermediate sub-plate using provided #6-32 x 3/4" pan head mount-

ing screws. Note: Orient the Sub-plate to say “THIS SIDE UP”. For the

two port, attach the device to the box by screwing the strap directly to the

box using provided #6-32 x 3/4" pan head mounting screws.

C. Place gasket over the box flange.

D. Assemble o-rings to the provided #6-32 x 1" oval head screws and

use these to assemble the cover plate to the box. Torque to 10 in/lbs

ensuring the gasket stays in place under the cover plate.

COMBO RECEPTACLE/KEYSTONE

This device should be installed in accordance with all appropriate codes

and standards. Warning: Turn off power to outlet box, using breaker or

fuse at service entrance. Verify that power has been removed by testing

with a circuit tester at the outlet box. Caution: This device is for use with

copper or copper-clad wire only.

A. After removing power as described above, use strip gauge on back of

outlet to strip all wires to desired length.

B. Attach wires according to the diagram below. The terminal screws

accept up to #12 AWG wire. Loop wires around screws in a counter-

clockwise fashion. Fasten terminal screws securely. Loosely fastened

wires may result in outlet failure and/or fire hazard.

C. Ensure divider is in place in box to separate high voltage from low volt-

age. WARNING: FAILURE TO INSTALL DIVIDER CAN CAUSE FIRE,

SERIOUS INJURY OR DEATH.

D. Assemble the desired Keystone Jack to the strap and wire per the

instructions enclosed with the product.

E. Attach the device to the box by screwing the strap directly to the box

using provided #6-32 x 3/4" pan head mounting screws. Note: Orient

the Sub-plate to say “THIS SIDE UP”.

F. Place gasket over the box flange.

G. Assemble o-rings to the provided #6-32 x 1" oval head screws and

use these to assemble the cover plate to the box. Torque to 10 in/lbs

ensuring the gasket stays in place under the cover plate.

Summary of content (2 pages)

PAGE 1
TAMPER-RESISTANT DUPLEX RECEPTACLE(S) FB-1 & FB-2 SERIES TAMPER-RESISTANT FLOOR BOX INSTALLATION INSTRUCTIONS This device should be installed in accordance with all appropriate codes and standards. Warning: Turn off power to outlet box, using breaker or fuse at service entrance. Verify that power has been removed by testing with a circuit tester at the outlet box. Caution: This device is for use with copper or copper-clad wire only.
PAGE 2
CAJA DE PISO RESISTENTE A LA MANIPULATIÓN INDEBIDA SERIES FB-1 & FB-2 INSTRUCCIONES DE INSTALACIÓN INSTRUCCIONES DE INSTALACIÓN AVISO: LEA ANTES DE INSTALAR EL DISPOSITIVO CARACTERÍSTICAS Y BENEFICIOS • Todas las cajas para piso FB*TR incluyen tomacorrientes resistentes a la manipulación indebida P&S de 15A, 125V. • Cumple la Sección 406.