Item #1001311064 Model #DFI-5988-WH USE AND CARE GUIDE MOTION SECURITY LIGHT Questions, problems, missing parts? Before returning to the store, call Defiant Customer Service 8 a.m.-7 p.m., EST, Monday-Friday, 9 a.m. - 6 p.m., EST, Saturday 1-866-308-3976 HOMEDEPOT.COM THANK YOU We appreciate the trust and confidence you have placed in Defiant through the purchase of this motion security light. We strive to continually create quality products designed to enhance your home.
Table of Contents Tools Required........................................3 Hardware Included..................................4 Package Contents...................................4 Installation.................................................5 Operation...................................................7 Care and Cleaning...................................10 Troubleshooting.......................................10 Table of Contents.......................................2 Safety Information..................
Pre-Installation PLANNING INSTALLATION Before installing the light fixture, ensure that all parts are present. Compare parts with the Hardware Included and Package Contents sections. If any part is missing or damaged, do not attempt to assemble, install, or operate this light fixture. Estimated installation time: 30 minutes SPECIFICATIONS Range Up to 70 ft. (21.
Pre-Installation (continued) HARDWARE INCLUDED NOTE: Hardware shown to actual size.
Installation the mounting 1 Determining location NOTE: The light fixture should be mounted approximately 8 ft. (2.4 m) above the ground. If the light fixture is mounted higher than recommended, aiming the sensor down will reduce the coverage area. Wall Mount □□ Determine the mounting location – wall or eave mount. □□ Position the lamp heads (A) in the general direction of the desired light coverage. □□ If needed, rotate the motion sensor (C) so the controls face the ground after installation.
Installation (continued) the 1-2- asy 4 Installing Connect™ the electrical 5 Making connections □□ Route the junction box wires through a hole in the 1-2- asy Connect™ (D). □□ Place the 1-2- asy Connect™ (D) against the junction box. □□ When mounting to a wall, the “UP” arrow must point upward. □□ Insert the junction box wires into the side of the terminal block and around the ground screw. Tighten terminal block screws using the mini-screwdriver (HH) and ground screw to secure the wires.
Installation (continued) around the light 7 Caulking fixture □□ Caulk around the 1-2- asy Connect™ (D) and mounting surface with silicone sealant (not included). D Operation 1 Adjusting the lamp heads the sensor controls 2 Rotating downward CAUTION: To avoid water damage and risk of electrical shock, the motion sensor controls must be facing the ground when installation is complete. WARNING: Risk of fire. Keep the lamp heads at least 2 in. (51 mm) from combustible materials.
Operation (continued) the motion sensor 3 Setting the sensor for testing 4 Adjusting detection zone □□ Perform a “walk test”: walk in an arc across the front of the motion sensor (C). □□ Watch the light. The light will come on and the red LED will flash indicating motion has been detected. □□ Stop, wait for the light to turn off, and then begin walking again. □□ Continue this process until the detection zone has been established.
Operation (continued) the DUALBRITE 7 Adjusting switch 8 Using manual mode NOTE: Manual mode overrides the motion sensor (C) and “ON‑TIME” control so the light will operate full bright. This feature only works at night and only for one night at a time. The motion sensor (C) will reset to motion sensing mode after 6 hours or sunrise, whichever comes first. Manual mode can be toggled on and off using a wall switch.
Care and Cleaning □□ To prolong the original appearance, clean the light fixture with clear water and a soft, damp cloth only. □□ Do not use paints, solvents, or other chemicals on this light fixture. They could cause a premature deterioration of the finish. This is not a defect in the finish and will not be covered by the warranty. □□ Do not spray the light fixture with a hose or power washer. Troubleshooting Problem Possible Cause Solution The light will not come on.
Troubleshooting (continued) Problem Possible Cause Solution The lights stay on continuously. □□ The motion sensor may be picking up a heat source, such as an air vent, dryer vent, or brightly painted, heat-reflective surface. □□ Decrease the “SENS” setting or reposition the motion sensor. □□ The motion sensor is in manual mode. □□ Switch the motion sensor to auto. See Using manual mode on page 9. □□ The light fixture is wired through a dimmer or timer.
Questions, problems, missing parts? Before returning to the store, call Defiant Customer Service 8 a.m.-7 p.m., EST, Monday-Friday, 9 a.m. - 6 p.m., EST, Saturday 1-866-308-3976 HOMEDEPOT.COM Retain this manual for future use.
Articulo #1001311064 Modelo #DFI-5988-WH GUÍA PARA EL USO Y CUIDADO LUZ DE SEGURIDAD POR MOVIMIENTO ¿Tiene preguntas, problemas o piezas faltantes? Antes de devolverlo a la tienda, llame a Servicio al Cliente de Defiant de 08 a.m.-7 p.m., EST, Lunes - Viernes, 09 a.m.-6 p.m., EST, sábado. 1-866-308-3976 HOMEDEPOT.COM GRACIAS Agradecemos la fe y la confianza que usted ha depositado en Defiant al comprar esta luz de seguridad por movimiento.
Contenido Herramientas Requeridas.....................15 Ferretería Incluida.................................16 Contenido del Paquete..........................16 Instalación...............................................17 Operación.................................................19 Cuidado y limpieza..................................22 Análisis de averías..................................22 Contenido.................................................14 Información de seguridad.......................
Antes de la instalación PLANIFICACIÓN DE LA INSTALACIÓN Antes de instalar el aparato de luz, esté seguro que estén todas las piezas. Compare las piezas con la Ferretería incluida y las secciones de Contenidos del paquete. Si cualquier pieza falta o está dañada, no intente ensamblar, instalar ni operar este aparato de luz.
Antes de la instalación (continuación) FERRETERÍA INCLUIDA NOTA: La ferretería se muestra en su tamaño real AA BB CC DD EE FRONT FF GG HH Pieza Descripción Cantidad AA Tapón de caucho 1 BB Tornillo del soporte de montaje 2 CC Tornillo del soporte de montaje 2 DD Tornillo del soporte de montaje 2 EE Tornillo grande de montaje (pre-instalado) 1 FF Tornillo pequeño de montaje 1 GG Soporte de montaje (no está a escala) 1 HH Mini-destornillador 1 CONTENIDO DEL PAQUETE A B D C
Instalación del sitio de 1 Determinación montaje NOTA: Esta lámpara debe ser instalada aproximadamente a 8 pies (2,4 m) por encima del suelo. Si se la instala a una altura más alta de la recomendada, se reducirá la zona de cobertura si apunta el detector hacia abajo. Montaje en pared □□ Determine el sitio de montaje – pared o alero. □□ Coloque los cabezales de la lámpara (A) en la dirección general de la cobertura de luz deseada.
Instalación (continuación) del 1-2- asy 4 Instalación Connect™ hacer las conexiones 5 Cómo eléctricas □□ Pase los cables de la caja de conexiones por un agujero en el 1-2- asy Connect™ (D). □□ Coloque el 1-2- asy Connect™ (D) contra la caja de conexiones. □□ Cuando la instale sobre una pared, la flecha “UP” (Hacia Arriba) debe apuntar hacia arriba. □□ Cuando la instale sobre un alero, la flecha “UP” (Hacia Arriba) debe apuntar hacia el edificio.
Instalación (continuación) alrededor del aparato 7 Calafatee de luz □□ Calafatee alrededor del 1-2- asy Connect™ (D) y de la superficie de montaje con un sellador de silicona contra la intemperie (no incluido). D Operación de los cabezales de la hacia abajo de los 1 Ajuste 2 Giro lámpara controles del detector PRECAUCIÓN: Para evitar daños por el agua y el riesgo de una descarga eléctrica, los controles del detector de movimiento deben estar de cara al suelo cuando la instalación esté terminada.
Operación (continuación) del detector para de la zona de 3 Calibración 4 Regulación prueba detección del detector de movimiento NOTA: Cuando el interruptor de “DURACIÓN” (“ON-TIME”) se fija en la posición “PRUEBA” (“TEST”) el aparato de luz operará durante el día o la noche. La luz permanecerá encendida 8 segundos después que todo movimiento se ha detenido. □□ Haga una “prueba caminando”: camine transversalmente a la parte frontal del detector de movimiento (C) siguiendo la trayectoria de un arco.
Operación (continuación) del interruptor 7 Regulación DUALBRITE 8 Uso del la fase manual NOTA: La fase manual anula el detector de movimiento (C) y el control de duración (“ON-TIME”), de esta forma la lámpara operará con todo su brillo. Esta característica funciona solamente en la noche y solamente una noche a la vez. El detector de movimiento (C) se reiniciará en la modalidad de detección de movimiento después de 6 horas o cuando salga el sol, lo que ocurra primero.
Cuidado y limpieza □□ Para prolongar la apariencia original, limpie la lámpara solo con agua limpia y un paño suave y húmedo. □□ No use pinturas, solventes ni otros químicos en este aparato de luz. Podrían ser la causa de una prematura deterioración del acabado. Esto no es un defecto del acabado y no será cubierto por la garantía. □□ No rocíe la lámpara con una manguera o lavadora a presión. Análisis de averías Problema Causa Probable Solución La luz no se enciende.
Análisis de averías (continuación) Problema Causa Probable Solución Las luces permanecen encendidas constantemente. □□ El detector de movimiento puede estar absorbiendo calor de una fuente de calor como una ventosa de aire, una secadora de aire, o una superficie pintada con colores brillantes y que refleja el calor. □□ Reduzca la calibración del alcance (“SENS”) o vuelva a colocar el detector de movimiento. □□ El detector de movimiento está en la fase manual.
¿Tiene preguntas, problemas o piezas faltantes? Antes de devolverlo a la tienda, llame a Servicio al Cliente de Defiant de 08 a.m.-7 p.m., EST, Lunes - Viernes, 09 a.m.-6 p.m., EST, sábado. 1-866-308-3976 HOMEDEPOT.COM Guarde este manual para uso futuro.