ASSEMBLY INSTRUCTION 2 seat outdoor swing ITEM CODE: CS62671 For any assistance with assembly or for missing parts please Contact with us Email: patiopostservice@lhgst.com Web: www.lhgst.com Adress:NO.
PRE-ASSEMBLY PREPARATION Before you start: 1.Choose a clean, level, spacious assembly area. Avoid hard surfaces that may damage the product 2.Take care when lifting. Product should be assembled as near as possible to the point of use 3.Ensure that you have all required contents for complete assembly 4.Always read the assembly instructions carefully before beginning assembly. 5.Keep all hardware parts and packaging out of reach of small children. 6.
PARTS LIST Page 3
Step 1 You will need the following • Prepare a surface with a blanket or cardboard. • Prepare 8x bolt Q sets. Thread bolt(Q) through washer(U). • Connect part(C) and part(D) to part(A) and part(B) as shown below. • Secure with 2x bolt Q sets at each connection, fasten with Allen Key(AA).
Step 2 You will need the following • Attach the 2x swing arms(E) to the frame. The short end of the late, closest to the rode connects to the feet(A&B). The long end of the plate faces down. • Secure with bolt(S), threaded from the outside, through swing arm(E). Place the plastic washer(N) between the swing arm(E) and the feet(A&B) Lock the inside with washer(U) and nut(V). Fasten with Allen key(AA)and Wrench(BB), as shown below. • Do this for all 4 connection points.
Step 3 You will need the following • Attach right armrest(F) to the swing arms(E) as shown below. • Thread bolt(S) from the outside through the armrest(F). Place the plastic washer(N) between the armrest and the swing arm. Lock the inside with washer(U) and nut(V). Fasten with Allen key(AA) and Wrench(BB), as shown below. • Repeat for the left armrest(G).
Step 4 You will need the following • With the aid of a 2nd person, attach the base and back plate(H) to the armrests. • Thread bolt(S) from the outside of the middle bar of the armrest, in through armrest and part(H). Lock the inside with washer(U) and nut(V). Fasten with Allen key(AA) and Wrench(BB), as shown below. You will need to bolts per armrest.
Step 5 You will need the following • Connect the top of the armrest to part(H). • Prepare 2x bolt R set, thread bolt(R) through washer(H) • Thread bolt R set from the inside of part(H) outwards. Place plastic washer(N) between the armrest and part(H). Fasten with Allen key(AA).
Step 6 You will need the following • Stand left and right tea table support(J&K) on the floor, attach the tea table connecting part(M) to the supports, as shown below. • Prepare 2x bolt R sets by threading bolt(R) through washer(U). • Connect parts(J&K) to part(M) with bolt R sets, fasten with Allen key(AA).
Step 7 You will need the following • • • • Place the tea table panel(L) upside down on the prepared surface. Place the completed table base on to part(L), as shown below. Prepare 4x bolt R sets by threading bolt(R) through washer(U). Secure the frame to the panel with bolt R sets and fasten with Allen key (AA).
Step 8 You will need the following • Place the completed table frame on the base and back plate(H),as shown below. • Prepare 2x bolt R sets by threading bolt(R) through washer(U) • Secure the table to the chair with a bolt R set on either side of the table, as shown below. Fasten with Allen key(AA). N.B.
Step 9 You will need the following • Secure the bottom of the table to part(H) • Insert bolt(T) down through the table as shown below. Insert plastic washer(P) in-between the table and the seat. Concave side up, flat side down. Lock the other side the bolt with washer(U) and nut(V), as shown below. • Fasten with Allen key(AA) and wrench(BB). N.B.
Assembly is complete Page 13
Page 14
