Dealer Cabinetry LLC Address: 202 N Georgia Ave,Bremen,GA 30110, USA Installation Notes This is intended only as a quick reference to the basics of tile installation. Tape is adhered to the front face of the mosaic sheets. Do not install this side into the setting material. Carefully read all instructions before starting installation. Please read and follow all specific installation products guidelines and specifications.
Dealer Cabinetry LLC Address: 202 N Georgia Ave,Bremen,GA 30110, USA For newly-built wall applications, the wall’s drywall is an adequate substrate to receive the mosaic. For existing wall or floor applications where the surface is structurally questionable or has a highly varied plane that will compromise the mosaic installation, add a layer of backerboard, such as Durock, to serve as the substrate to receive the mosaic. If possible, dry fit mosaic sheets and inspect before installing.
Dealer Cabinetry LLC Address: 202 N Georgia Ave,Bremen,GA 30110, USA Mosaic Installation Process 1. Skimming The installation surface must be smooth and clean to ensure proper installation. It may be necessary to lay a thin layer of setting material on the surface to ensure that it is ready for the tile. Allow 12 hours to dry if layer of setting material is needed.
Dealer Cabinetry LLC Address: 202 N Georgia Ave,Bremen,GA 30110, USA 2. Guide Lines Measure the space in which the mosaic is being installed to determine the best fit for your tile. Use a straight edge and level to help you align the tile as you work. Construct a grid on the substrate that is equal to nine sheets of the tile. NOTE: Be sure to account for the spaces between each sheet of tile when measuring.
Dealer Cabinetry LLC Address: 202 N Georgia Ave,Bremen,GA 30110, USA 3. Applying Setting Material Mix setting material. First coat: apply setting material with the smooth edge of a trowel to a section no larger than one section of the grid. Second coat: create even ridges in the setting material by “combing” the material with the notched edge of the trowel.
Dealer Cabinetry LLC Address: 202 N Georgia Ave,Bremen,GA 30110, USA 4. Installing the Tile The sheets of mosaic have a clear tape covering on the front face of the tile. This allows the mosaic design to be seen during installation. Apply the backside of each sheet into the setting material, with the tape side face out. Using a float tool, tap across the surface to adhere the mosaic securely into the setting material.
Dealer Cabinetry LLC Address: 202 N Georgia Ave,Bremen,GA 30110, USA 5. Securing Mosaic Sheets It is important to create a secure bond between the tiles and the setting material. Using the float tool tap across the surface to adhere the mosaic securely. This also ensures the final exposed plane of the mosaic is consistent and uniform in height.
Dealer Cabinetry LLC Address: 202 N Georgia Ave,Bremen,GA 30110, USA 6. Adjusting Spacing This can be a time consuming process, but is important to ensure a professional installation. Adjust while material is still wet. Adjust any tiles that are uneven and ensure that all gaps are of equal width and height. Do this by cutting through the clear tape and moving tiles with a small trowel.
Dealer Cabinetry LLC Address: 202 N Georgia Ave,Bremen,GA 30110, USA 7. Grouting Grout can be applied to a clean, dry surface. (See Step 8 “Expansion Joints”) Before applying grout be sure that the mosaic surface is clean and all clear tape is removed from the tiles. Peel tape in a diagonal motion. Thorough cleaning may involve removing excess setting material from the mosaic’s joint with a knife, as well as cleaning off all dust and particles.
Dealer Cabinetry LLC Address: 202 N Georgia Ave,Bremen,GA 30110, USA 8. Expansion Joints Expansion joints should be installed at all “changes in plane” of the mosaic and where the mosaic meets an adjoining surface, such as in a corner. Fill these space(s) with a silicone caulking sealant in place of grout to create expansion joints at these locations.
Dealer Cabinetry LLC Address: 202 N Georgia Ave,Bremen,GA 30110, USA 9. Cleaning The mosaic should be ready to be cleaned about 30-60 minutes after grouting. Use a sponge and clean water and scrub in a circular motion, removing excess grout and smoothing all joints. Continue to wipe down the tiles until clean. NOTE: Cleaning methods vary based upon the type of grout used in the installation. For example, a urethane grout must be cleaned earlier and more frequently that cementitious grout.
Dealer Cabinetry LLC Address: 202 N Georgia Ave,Bremen,GA 30110, USA How to Clean Greasy Backsplash Behind Stove Backsplashes have come a long way over the years. The first backsplashes to protect the wall behind a stove were made of plastic and linoleum. Today, backsplashes are made of many different materials, such as slate, ceramic, glass, marble and stainless steel.
Dealer Cabinetry LLC Address: 202 N Georgia Ave,Bremen,GA 30110, USA Ceramic, Marble, Glass and Plastic Backsplashes 1. 2. 3. 4. Spray the surface with an all-purpose cleaner designed to remove grease. Let it sit for 20 to 30 minutes. Wipe down your backsplash with a soft rag or paper towels. Repeat if necessary. Use a heavy duty degreasing cleaner such as Grease Grizzly or Goo Gone if your grease is tough to remove. Rinse with a clean, wet rag when done to remove all cleaning residue.
Dealer Cabinetry LLC Address: 202 N Georgia Ave,Bremen,GA 30110, USA 4. Scrub your slate backsplash with the soapy water and a scrub brush, if all goes well in Step 3. Dip your brush into the soapy water frequently while scrubbing. 5. Rinse with a clean, wet rag to remove any remaining soap residue.
